5.45×39mm

, 7.62×51mm NATO, 7.62×39mm, 5.56×45mm NATO, 5.45×39 mm. The 5.45×39 mm cartridge was developed in the early 1970s by a group of Soviet designers and engineers under the direction of M. Sabelnikov. Further group members were: L. I. Bulavsky, B. B. Semin, M. E. Fedorov, P. F. Sazonov, V. Volkov, V. A. Nikolaev, E. E. Zimin and P. S. Korolev. The 5.45×39 mm couples a sensible case volume (1.75 ml) to bore area (23.99 mm2/0.2399 cm2) ratio with ample space for loading relatively long slender projectiles that can provide good aerodynamic efficiency and external ballistic performance for the projectile diameter. The Soviet original military issue 7N6 cartridge variant introduced in 1974 is loaded with full metal jacket bullets that have a somewhat complex construction. The long boat-tail projectile's jacket is clad in gilding metal. The unhardened steel (steel 10) rod penetrator core is covered by a thin lead inlay which does not fill the entire point end, leaving a hollow cavity inside the nose. The bullet is cut to length during the manufacturing process to give the correct weight. The 7N6 uses a boat-tail design to reduce drag and there is a small lead plug crimped in place in the base of the bullet. The lead plug, in combination with the air space at the point of the bullet, has the effect of moving the bullet's center of gravity to the rear; the hollow air space also makes the bullet's point prone to deformation when the bullet strikes anything solid, inducing yaw. The brown-lacquered steel case is Berdan primed. Its length makes it slightly longer than the 7.62×39 mm case which measures exactly . The primer has a copper cup and is sealed with a heavy red lacquer. The propellant charge is a ball powder with similar burning characteristics to the WC844 powder used in 5.56×45mm NATO ammunition. The 7N6 cartridge weight is . Tests indicate the free recoil energy delivered by the 5.45×39 mm AK-74 assault rifle is , compared to delivered by the 5.56×45 mm NATO in the M16 assault rifle and delivered by the 7.62×39 mm in the AKM assault rifle. Military 5.45×39 mm ammunition was produced in the former Soviet Union, and in the GDR, and is produced in Bulgaria, Poland and Romania. In the former Soviet Union this ammunition is produced in Russia, Armenia, and Azerbaijan. Ukraine used to produce Soviet small arms ammunition before the Russians took over the Luhansk Cartridge Plant in 2014, but managed to resume production of 5.45×39 mm in 2024 and start producing 5.56×45 mm NATO ammunition as well. Kazakhstan plans on producing several types of small arms ammunition including the 5.45×39 mm, with mass production expected to begin in 2024. Use in the Soviet-Afghan War When the AK-74 saw service during the Soviet-Afghan War, the original 5.45×39 mm 7N6 ball round quickly became known amongst the Afghan mujahideen as the "poison bullet": it caused more damage to internal tissue and organs in comparison to the 7.62×39 mm round used by the AK-47 and AKM (thanks to tumbling caused by the air space in the tip). Wounded fighters, often left untreated for days coupled with a severe shortage of antibiotics, quickly developed infections including gangrene, leading the mujahideen to mistakenly believe that the Soviets made use of poisoned bullets. Use in Russo-Ukrainian War During April 2024 of the Russo-Ukrainian War, Ukrainian forces used predominately 5.45×39 mm ammunition according to American national Jonathan Poquette, a member of the Chosen Company, attached to the Ukrainian 59th Motorized Brigade. He cited a number of reasons, firstly an unorganised donation of rifles that fired NATO standard 5.56×45mm NATO. Some units received these weapons, others did not. Secondly, the donation of 5.56×45 mm NATO ammunition recently along with other aid from the West was lacking. The third reason is the fact that Ukraine was part of the Soviet Union, meaning that weapons firing 5.45×39 mm ammunition were more widely available. Further, Russian forces use it as their standard ammunition. Saying that "if you go and you attack a Russian position and you need to resupply, the Russians are usually going to have 5.45×39 mm." ==Cartridge dimensions==

The 5.45×39 mm has a 1.75 mL (27 gr ) cartridge case capacity. 5.45×39 mm maximum C.I.P. cartridge dimensions. Americans would define the shoulder angle at ≈ 20.3°. The common rifling twist rate for this cartridge is 255 mm (1 in 10 inches), 4 grooves, Ø lands = 5.40 mm, Ø grooves = 5.60 mm, land width = 2.60 mm and the primer type is either berdan or small rifle. According to the official C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) rulings the 5.45×39 mm can handle up to Pmax piezo pressure. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of this maximum C.I.P. pressure to certify for sale to consumers. This means that 5.45×39 mm chambered arms in C.I.P. regulated countries are currently (2014) proof tested at PE piezo pressure. ==Wounding effects==

Early ballistics tests demonstrated a pronounced tumbling effect with high speed cameras. Some Western authorities believed this bullet was designed to tumble in flesh to increase wounding potential. At the time, it was believed that yawing and cavitation of projectiles were primarily responsible for tissue damage. The tumbling effect was caused by the hollow point of the bullet - as the bullet strikes a target, the core inside the bullet flies forward, shifting the center of gravity and causing the bullet to tumble. Martin Fackler conducted a study with an AK-74 assault rifle using live pigs and ballistic gelatin: "The result of our preset test indicate that the AK-74 bullet acts in the manner expected of a full-metal-cased military ammunition—it does not expand or fragment when striking soft tissues". Multiple x-rays done on human tissue support this assertion. The average frequency of fragmentation with 7N6 fired into extremities with injuries was 18%. This is compared to 57% with M193 5.56×45 in the same testing. Fragmentation of 5.45 mm bullets was observed predominantly in wounds of the lower extremities with fractures of long bones. Most organs and tissue were too flexible to be severely damaged by the temporary cavity effect caused by yaw and cavitation of a projectile. Terminal ballistics against body armor According to the Russian Defense Ministry's third Central Research Institute, the Russian military should consider switching back to improved 7.62×39 mm ammunition due to 5.45×39 mm penetration insufficiency against body armor at longer ranges. However, the change is yet to happen due to the development of the 7N39 cartridge with great penetration capabilities. ==5.45×39mm cartridge variants==

Enhanced penetration cartridges As body armor saw increasing use in militaries, the original 7N6 standard service cartridge bullet construction was changed several times to improve penetration. The rounds are loaded to produce a maximal pressure of . The 7N10 "improved penetration" cartridge was introduced in 1992. The 7N10 boat-tail bullet weighs and the weight of the lengthened sleeker steel (high-carbon steel U12A) penetrator made of steel 70 was increased to and the lead plug in front of it was discarded. The hollow cavity at the front of these projectiles was reduced significantly compared to previous 7N6(M) projectiles. In 1994 the 7N10 design was improved by filling the remaining hollow cavity in the projectiles front with lead and reducing the weight of the penetrator to resulting in a bullet weighing . Upon impacting a hard target, soft lead is pressed sideways by the steel penetrator, tearing the jacket. It has a ballistic coefficient (G1 BC) of approximately 0.351 and (G7 BC) of approximately 0.176. The 7N10 cartridge replaced the previous variants as standard Russian service round and can penetrate a 16 mm thick St3 steel plate at 100 m and 6B3TM ballistic vest at 200 m. 7N10 bullets have a violet/purple identification ring above the cartridge neck. The 7N10 and 7N6(M) cartridges have practically identical external ballistic characteristics, meaning they can share identical sighting lines and optics on firearms. The rounds are loaded to produce a maximal pressure of . The rounds are loaded to produce a maximal pressure of . Tracer cartridges Besides that the tracer cartridges 7T3 and 7T3M were developed. The 7T3 production bullet length was long and weighed . After 1976 a new lighter and shorter long bullet was selected as a replacement for the original bullet. These bullets can be identified by their green marked tips. The tracer projectile has a shorter ogival profile and for 7T3 ammunition burns out to and for 7T3M ammunition ignites at burning out to . The rounds are loaded to produce a maximal pressure of . Training and instruction cartridges rifle equipped with a blank fire adaptor For training purposes the blank cartridges 7H3, 7H3M and 7Kh3 were developed. These rounds have a hollow white plastic imitation projectile. When these training rounds are used, the barrel of the gun is fitted at the muzzle with a blank fire adapter to produce a gas pressure build-up for cycling the gun, as well as a breakup aid for their plastic projectiles. For instruction purposes the 7H4 training or dummy cartridge (which has longitudinal grooves) was developed. Special purpose cartridges For special purposes the 7U1 subsonic cartridge with a black and green painted meplat and CAP (cartridge for underwater) were developed. The 7U1 subsonic cartridge weight is and is loaded with a projectile which is fired with a muzzle velocity of yielding muzzle energy. Accuracy of fire at (R50) is Basic specifications • R50 at means the closest 50 percent of the shot group will all be within a circle of the mentioned diameter at . • The twist rate used in the AK-74M assault rifle that has been adopted as the new service rifle of the Russian Federation in 1991 is . ==Civil use==

The 5.45×39 mm was developed by the Soviet Union for military use and it was not intended to create civilian weapons in this chambering. When 5.45×39 mm ammunition finally became available for sale to civilians, several arms manufacturers started to offer semi-automatic AK-74 variants in the calibre for civilian use. Sometimes these weapons combine parts originating from Russia or Eastern European states and parts produced elsewhere. Only a few civilian 5.45×39 mm weapons were developed and commercially offered. Non-AK-74 rifles and commercial offerings include the East German SSG 82 bolt action rifle and the Russian CRS-98 "Vepr-5, 45" semi-automatic carbine and Saiga semi-automatic rifle. In May 2008 the Smith & Wesson M&P15R was introduced. This was a standard AR-15 rifle chambered for the 5.45×39 mm cartridge and was Smith & Wesson's first AR-variant rifle in a chambering other than 5.56×45 mm NATO and is no longer in current (2012) production. The civilian version of the Tavor TAR-21 rifle produced for the US market includes an optional 5.45×39mm conversion kit. Commercial 5.45×39 mm ammunition The US ammunition manufacturer Hornady produces commercial polymer-coated steel case 5.45×39 mm ammunition loaded with polymer tipped V-MAX bullets with a stated ballistic coefficient (G1 BC) of 0.285. It is unknown if Hornady plans to continue manufacturing this caliber, as the last confirmed lot number was released in 2021. WOLF Performance Ammunition offers several Berdan primed commercial 5.45×39mm loads. The Russian ammunition manufacturer Barnaul Cartridge Plant also offers several Berdan primed commercial sporting and hunting 5.45×39 mm cartridges. Barnaul states that their 5.45×39mm cartridges produce a maximal pressure of 294,2 MPa (41,054 psi) and have a bullet dispersion R100 of at a range of , meaning every shot of a shot group will be within a circle of the mentioned diameter at . The American firearms corporation Century International Arms offers Ukrainian made 5.45×39mm cartridges with steel casings and bi-metal (copper/steel) jacketed bullets under the Red Army Standard Ammunition brand. The Russian manufacturer Tula Arms Plant states that its Tula Ammunition cartridges comply with the 5.45×39 mm C.I.P. rulings producing a maximal pressure of 302.7 MPa (43,900 psi) and keeps their qualities under various climatic and weather conditions independent of the season and at a temperature range from . Tula's full metal jacket bullet has a stated ballistic coefficient (G1 BC) of 0.329 and its hollow-point bullet has a stated ballistic coefficient (G1 BC) of 0.301. As of August 20, 2021, ammunition manufactured in Russia was added to the sanctions found in the CBW Act of 1991, (in retaliation to the Russian invasion of Ukraine) barring the importation of the majority of the cartridges listed above, to the United States. == Gallery ==

Image:Cartridge Kalashnikov AK-74.svg|5.45×39mm 7N6(M) Cartridge Sectional DrawingA: projectile jacketB: steel coreC: hollow cavityD: lead inlayE: propelling charge File:5.45x39.jpg|5.45×39mm cartridge with steel cartridge case. Image:RussianWP.jpg|Wound profiles of Russian small-arms ammunition compiled by Martin Fackler on behalf of the U.S. military ==See also==