MOLLE

Even prior to the introduction of MOLLE, another lightened system of load-carrying equipment had been developed. Known as the Individual Integrated Fighting System (IIFS) and also TLBV, it intended to replace the older All-purpose Lightweight Individual Carrying Equipment (ALICE). The IIFS load-bearing vests (rifle and 40mm grenadier configurations) had their origins in the vests used by US Navy SEALS and other special operations forces in Vietnam. Though the IIFS did not live up to its expected purpose, it did lay the groundwork for future equipment. ALICE and IIFS packs In 1988, the US Army adopted a new internal frame pack system, a subsystem in IIFS. The design was based on commercial backpacks modified for military use with the addition of a special fighting vest and a detachable patrol pack. The original focus was to develop a load-carrying system for use in cold weather. However, in the end, the US Army decided the new internal frame pack would be the replacement for the external framed All-purpose Lightweight Individual Carrying Equipment (ALICE) system. Production and distribution started in 1990 but by 1993 it was evident that the new internal frame pack was unacceptable to a large number of combat personnel. Although a key problem with the internal frame was durability due to poor manufacturing, the IIFS pack system was also judged to have some basic design flaws. Based on a survey of users by the US Army Training and Doctrine Command (TRADOC), soldiers claimed the pack was too hot against the back in warm climates, and was unstable and uncomfortable when heavily loaded. While many of the features of the system were liked (e.g., the patrol pack, and capacity of the main pack), it was judged not to meet the overall requirements of the Army. In spite of this rejection, most units surveyed (6 of 9), still favored having both load-carrying systems: the ALICE for warm and temperate climates, and the internal frame system for cold weather operations. == Development ==

An early prototype of a modular system was under development before the call for a front-end analysis for a new & improved military load carrying system in 1994. during its routine surveys of users of Natick developed food, clothing, shelters, and individual equipment items. and would lighten the soldier's load. == Fielding ==

The MOLLE system was introduced in 1997, but did not see widespread issue until after the September 11 attacks in 2001, primarily by U.S. troops serving in Afghanistan and Iraq. MOLLE entered full rate production in August 2001. Fielding began in October 2001. == Criticisms ==

Early criticisms of the MOLLE system emerged, particularly from the Army. Many of these criticisms have centered on the sustainment-load pack and frame, due to the external plastic frame being too fragile and subject to breaking in the field (since mitigated), that the zippers have a tendency to burst when stuffed full and that the pack's straps lack sufficient length to be used with bulky body armor. The first generation of this system used a ball and socket joint between the frame and rucksack belt (which in itself formed the waistbelt of the MOLLE vest). This method led to numerous lower back injuries due to the ball (mounted on the frame) missing the socket on the waistbelt and hurting the user's body. Subsequent redesign of the SDS MOLLE led to the deletion of this feature, with the vest (aka FLC) and ruck/frame becoming separate non-integral items. == Attachment technique ==

Terminology The term 'MOLLE' technically only applies to the individual equipment system (manufactured by Specialty Defense Systems) rather than the PALS (Pouch Attachment Ladder System) webbing that it utilizes. Despite that, 'MOLLE' is often casually used to describe any load bearing system or component in general that utilizes the woven PALS webbing. Although PALS was proprietary to Natick Labs from 1998 to 2016, Pouches are attached by aligning the PALS webbing on the platform and the pouch so that the rows interleave with each other and the bartacks are aligned. An anchoring strap on the pouch is then woven through both sets of webbing and secured with a snap fastener at the base. This interwoven and interlocking design keeps the pouch securely in place. In other words, the height of webbing can be off by about half of 1/10th an inch, and still remain within tolerance. In metric, the tolerance is within roughly 1.25 mm on the low end and roughly 2.00 mm on the high end. The misalignment of divider bartacks in 1.5 inch insert loops is considered acceptable within approx. wide. Derivatives Derivatives based on the MOLLE attachment method (such as the Tactical Tailor MALICE clip system) have also been developed. Any system that utilizes modular attachment methods and is usable with U.S. general issue MOLLE components is often considered "MOLLE-compatible" or is called a "MOLLE" system. Increasingly, non-military manufacturers are incorporating PALS onto outdoor equipment. There are three general modes of attachment in the MOLLE category; the "Natick Snap", which uses a polyethylene reinforced webbing strap with the 'pushthedot' snap fastener for security; the polymer "Malice" clip, developed by Tactical Tailor as an alternative to the Natick Snap concept, which interweaves like the Natick Snap but terminates in a semi-permanent closure that requires a screwdriver or other flat-tipped object to disengage; and a variety of attachments that fall into the "Weave & Tuck" category, in which the end of an interwoven strap is tucked into an item's backing after attachment to a vest or pack (Paraclete's SofStrap and Spec Ops Brand's hybrid attachment). == Components ==

The MOLLE system has several components; a Fighting Load Carrier (FLC) vest, modular pouches/pockets, large rucksack (aka main pack & Sleep System Carrier), assault pack, pack frame, and hydration system. The modular pouches can carry 30 round ammunition magazines, squad automatic weapon 100 and 200 round magazines, fragmentation grenades, 40mm grenades, 9mm magazines, and 1 quart canteens. The TAP is covered with PALS webbing and storage for up to eight rifle magazines (six 5.56 magazines + two 7.62 NATO magazines, or eight 5.56 magazines). ; Assault pack: The Assault Pack is a backpack with 2000 cubic inches (32L) of storage space. ; Medium rucksack: The Medium Rucksack is an external frame rucksack with 3000 cubic inches (50L) of storage space. It is designed to be worn over body armor and supports loads up to 60 lbs. It features a large main compartment with internal dividers for items like the hydration system, 60mm mortar rounds, along with a harness for ASIP radios. Two smaller compartments are located outside the main compartment. The pack is adorned in PALS webbing. ; Large rucksack: The Large Rucksack is an external frame rucksack with 4000 cubic inches (65L) of storage space. It features a large main compartment with an internal divider between the upper and lower half for organizing loads. It is covered with PALS webbing, and ALICE webbing on the side to support legacy items such as the 2 quart canteen pouch. It is highly adjustable for comfort and load distribution. The MOLLE large rucksack with straps and frame weighs when empty. ; Hydration bladder: Plastic hydration bladder to supplement the and canteens for on-the-go hydration. ; Modular pouches: Pouches of various utility that can be attached wherever PALS webbing exists. One type is a "sustainment pouch", which holds three MREs. The various MOLLE pouches are commonly used to carry ammunition, gas masks, batons, flares, grenades, canteens, handcuffs and pepper spray. The custom pouches include PALS-compatible pistol holders, hydration pouches, and utility pouches. These pouches are normally secured through the use of straps, ALICE clips or speedclips. == See also ==