Bandwidth (signal processing)

Bandwidth is a key concept in many telecommunications applications. In radio communications, for example, bandwidth is the frequency range occupied by a modulated carrier signal. An FM radio receiver's tuner spans a limited range of frequencies. A government agency (such as the Federal Communications Commission in the United States) may apportion the regionally available bandwidth to broadcast license holders so that their signals do not mutually interfere. In this context, bandwidth is also known as channel spacing. For other applications, there are other definitions. One definition of bandwidth, for a system, could be the range of frequencies over which the system produces a specified level of performance. A less strict and more practically useful definition will refer to the frequencies beyond which performance is degraded. In the case of frequency response, degradation could, for example, mean more than 3 dB below the maximum value or it could mean below a certain absolute value. As with any definition of the width of a function, many definitions are suitable for different purposes. In the context of, for example, the sampling theorem and Nyquist sampling rate, bandwidth typically refers to baseband bandwidth. In the context of Nyquist symbol rate or Shannon-Hartley channel capacity for communication systems it refers to passband bandwidth. The '''''' of a simple radar pulse is defined as the inverse of its duration. For example, a one-microsecond pulse has a Rayleigh bandwidth of one megahertz. The '''''' is defined as the portion of a signal spectrum in the frequency domain which contains most of the energy of the signal. == x dB bandwidth ==

illustrating the concept of −3 dB bandwidth at a gain of approximately 0.707 In some contexts, the signal bandwidth in hertz refers to the frequency range in which the signal's spectral density (in W/Hz or V2/Hz) is nonzero or above a small threshold value. The threshold value is often defined relative to the maximum value, and is most commonly the , that is the point where the spectral density is half its maximum value (or the spectral amplitude, in \mathrm{V} or \mathrm{V/\sqrt{Hz}}, is 70.7% of its maximum). This figure, with a lower threshold value, can be used in calculations of the lowest sampling rate that will satisfy the sampling theorem. The bandwidth is also used to denote system bandwidth, for example in filter or communication channel systems. To say that a system has a certain bandwidth means that the system can process signals with that range of frequencies, or that the system reduces the bandwidth of a white noise input to that bandwidth. The 3 dB bandwidth of an electronic filter or communication channel is the part of the system's frequency response that lies within 3 dB of the response at its peak, which, in the passband filter case, is typically at or near its center frequency, and in the low-pass filter is at or near its cutoff frequency. If the maximum gain is 0 dB, the 3 dB bandwidth is the frequency range where attenuation is less than 3 dB. 3 dB attenuation is also where power is half its maximum. This same half-power gain convention is also used in spectral width, and more generally for the extent of functions as full width at half maximum (FWHM). In electronic filter design, a filter specification may require that within the filter passband, the gain is nominally 0 dB with a small variation, for example within the ±1 dB interval. In the stopband(s), the required attenuation in decibels is above a certain level, for example >100 dB. In a transition band the gain is not specified. In this case, the filter bandwidth corresponds to the passband width, which in this example is the 1 dB-bandwidth. If the filter shows amplitude ripple within the passband, the x dB point refers to the point where the gain is x dB below the nominal passband gain rather than x dB below the maximum gain. In signal processing and control theory the bandwidth is the frequency at which the closed-loop system gain drops 3 dB below peak. In communication systems, in calculations of the Shannon–Hartley channel capacity, bandwidth refers to the 3 dB-bandwidth. In calculations of the maximum symbol rate, the Nyquist sampling rate, and maximum bit rate according to the Hartley's law, the bandwidth refers to the frequency range within which the gain is non-zero. The fact that in equivalent baseband models of communication systems, the signal spectrum consists of both negative and positive frequencies, can lead to confusion about bandwidth since they are sometimes referred to only by the positive half, and one will occasionally see expressions such as B = 2W, where B is the total bandwidth (i.e. the maximum passband bandwidth of the carrier-modulated RF signal and the minimum passband bandwidth of the physical passband channel), and W is the positive bandwidth (the baseband bandwidth of the equivalent channel model). For instance, the baseband model of the signal would require a low-pass filter with cutoff frequency of at least W to stay intact, and the physical passband channel would require a passband filter of at least B to stay intact. == Relative bandwidth ==

The absolute bandwidth is not always the most appropriate or useful measure of bandwidth. For instance, in the field of antennas the difficulty of constructing an antenna to meet a specified absolute bandwidth is easier at a higher frequency than at a lower frequency. For this reason, bandwidth is often quoted relative to the frequency of operation which gives a better indication of the structure and sophistication needed for the circuit or device under consideration. There are two different measures of relative bandwidth in common use: fractional bandwidth (B_\mathrm F) and ratio bandwidth (B_\mathrm R). In the following, the absolute bandwidth is defined as follows, B = \Delta f = f_\mathrm H - f_\mathrm L where f_\mathrm H and f_\mathrm L are the upper and lower frequency limits respectively of the band in question. Fractional bandwidth Fractional bandwidth is defined as the absolute bandwidth divided by the center frequency (f_\mathrm C), B_\mathrm F = \frac {\Delta f}{f_\mathrm C} \, . The center frequency is usually defined as the arithmetic mean of the upper and lower frequencies so that, f_\mathrm C = \frac {f_\mathrm H + f_\mathrm L}{2} \ and B_\mathrm F = \frac {2 (f_\mathrm H - f_\mathrm L)}{f_\mathrm H + f_\mathrm L} \, . However, the center frequency is sometimes defined as the geometric mean of the upper and lower frequencies, f_\mathrm C = \sqrt {f_\mathrm H f_\mathrm L} and B_\mathrm F = \frac {f_\mathrm H - f_\mathrm L}{\sqrt {f_\mathrm H f_\mathrm L}} \, . While the geometric mean is more rarely used than the arithmetic mean (and the latter can be assumed if not stated explicitly) the former is considered more mathematically rigorous. It more properly reflects the logarithmic relationship of fractional bandwidth with increasing frequency. For narrowband applications, there is only marginal difference between the two definitions. The geometric mean version is inconsequentially larger. For wideband applications they diverge substantially with the arithmetic mean version approaching 2 in the limit and the geometric mean version approaching infinity. Fractional bandwidth is sometimes expressed as a percentage of the center frequency (percent bandwidth, \%B), \%B_\mathrm F = 100 \frac {\Delta f}{f_\mathrm C} \, . Ratio bandwidth Ratio bandwidth is defined as the ratio of the upper and lower limits of the band, B_\mathrm R= \frac {f_\mathrm H}{f_\mathrm L} \, . Ratio bandwidth may be notated as B_\mathrm R:1. The relationship between ratio bandwidth and fractional bandwidth is given by, B_\mathrm F = 2 \frac {B_\mathrm R - 1}{B_\mathrm R + 1} and B_\mathrm R = \frac {2 + B_\mathrm F}{2 - B_\mathrm F} \, . Percent bandwidth is a less meaningful measure in wideband applications. A percent bandwidth of 100% corresponds to a ratio bandwidth of 3:1. All higher ratios up to infinity are compressed into the range 100–200%. Ratio bandwidth is often expressed in octaves (i.e., as a frequency level) for wideband applications. An octave is a frequency ratio of 2:1 leading to this expression for the number of octaves, \log_2 \left(B_\mathrm R\right) . == Noise equivalent bandwidth ==

The noise equivalent bandwidth (or equivalent noise bandwidth (enbw)) of a system of frequency response H(f) is the bandwidth of an ideal filter with rectangular frequency response centered on the system's central frequency that produces the same average power outgoing H(f) when both systems are excited with a white noise source. The value of the noise equivalent bandwidth depends on the ideal filter reference gain used. Typically, this gain equals |H(f)| at its center frequency, but it can also equal the peak value of |H(f)|. The noise equivalent bandwidth B_n can be calculated in the frequency domain using H(f) or in the time domain by exploiting the Parseval's theorem with the system impulse response h(t). If H(f) is a lowpass system with zero central frequency and the filter reference gain is referred to this frequency, then: B_n = \frac{\int_{-\infty}^{\infty} |H(f)|^2 df}{2|H(0)|^2} = \frac{\int_{-\infty}^{\infty} |h(t)|^2 dt}{2\left|\int_{-\infty}^{\infty} h(t)dt\right|^2} \, . The same expression can be applied to bandpass systems by substituting the equivalent baseband frequency response for H(f). The noise equivalent bandwidth is widely used to simplify the analysis of telecommunication systems in the presence of noise. == Photonics ==

In photonics, the term bandwidth carries a variety of meanings: • the bandwidth of the output of some light source, e.g., an ASE source or a laser; the bandwidth of ultrashort optical pulses can be particularly large • the width of the frequency range that can be transmitted by some element, e.g. an optical fiber • the gain bandwidth of an optical amplifier • the width of the range of some other phenomenon, e.g., a reflection, the phase matching of a nonlinear process, or some resonance • the maximum modulation frequency (or range of modulation frequencies) of an optical modulator • the range of frequencies in which some measurement apparatus (e.g., a power meter) can operate • the data rate (e.g., in Gbit/s) achieved in an optical communication system; see bandwidth (computing). A related concept is the spectral linewidth of the radiation emitted by excited atoms. == See also ==