Security alarm

The most basic alarm consists of at least one sensor to detect trespassers and an alerting device to indicate the intrusion. However, a typical premises security alarm employs the following components: • Alarm control panel (ACP), or simply panel: The panel reads sensor inputs, tracks arm/disarm status, and signals intrusions. In a modern device, there are typically one or more computer circuit boards inside a metal enclosure. Many newer networks often use sealed plastic boxes. Some also have their control units built-into the keypad or other human-machine interface. • Sensors: In a security alarm, some sensors detect intrusions. Sensors' locations are at the perimeter of the protected area, within it, or both. Sensors can detect intruders by different methods. • Alerting devices indicate an alarm condition. Most commonly, these are bells, sirens, and/or flashing lights. Alerting devices serve the dual purpose of warning occupants of intrusion and potentially scaring off burglars. • Keypads: Keypads are devices that function as the human-machine interface to the system. In addition to buttons, keypads typically feature indicator lights, a small multi-character display, or both. In addition to the system itself, security alarms often offer a monitoring service. In the event of an alarm, the premises control unit contacts a central monitoring station. Operators at the station take appropriate action, such as contacting property owners, notifying the police, or dispatching private security forces. Such alerts transmit via dedicated alarm circuits, telephone lines, or the internet. ==Sensor types==

Hermetically sealed reed switches The hermetically sealed reed switch is a common type of two-piece sensor. This switch operates with an electrically conductive switch that is either normally open or normally closed when under the influence of a magnetic field in respect to proximity to the second piece, which contains a magnet. When the magnet moves away from the reed switch, the reed switch either closes or opens, based on the normally closed or open design. This action, coupled with an electric current, allows an alarm control panel to detect a fault on that zone or circuit. These sensors are common, are found wired directly to an alarm control panel, or are typically found in wireless door or window contacts as sub-components. Passive infrared detectors used to detect motion The passive infrared (PIR) motion detector is one of the most common sensors found in household and small business environments. This sensor does not generate or radiate energy; it works entirely by detecting the heat energy given off by other objects. PIR sensors identify abrupt changes in temperature at a given point. As an intruder walks in front of the sensor, the temperature at that point will rise from room temperature to body temperature and then back again. This quick change triggers the detection. PIR sensors designed to be wall- or ceiling-mounted come in various fields of view. PIRs require a power supply in addition to the detection signaling circuit. Infrasound detectors The infrasound detector works by detecting infrasound, or sound waves at frequencies below 20Hz. Sounds at those frequencies are inaudible to the human ear. Due to its inherent properties, infrasound can travel distances of many hundreds of kilometers. The entire infrasound detection system consists of the following components: a speaker (infrasound sensor) as a microphone input, an order-frequency filter, an analog-to-digital (A/D) converter, and an microcomputer to analyze the recorded signal. If a potential intruder tries to enter into a house, they test whether it is closed and locked, uses tools on openings, and/or applies pressure, creating low-frequency sound vibrations. Before the intruder breaks in, the infrasound detector automatically detects the intruder's actions. The purpose of such a system is to detect burglars before they enter the house to avoid both theft and vandalism. The sensitivity is dependent on the size of a home and the presence of animals. Ultrasonic detectors These active detectors transmit ultrasonic sound waves that are inaudible to humans using frequencies between 15 kHz and 75 kHz. The Doppler shift principle is the underlying method of operation which detects a change in frequency due to object motion. This detection occurs when the object must cause a change in the ultrasonic frequency to the receiver relative to the transmitting frequency. The ultrasonic detector operates by the transmitter emitting an ultrasonic signal into the area to be protected. Solid objects (such as the surrounding floor, walls, and ceiling) reflect sound waves, which the receiver will detect. Because ultrasonic waves are transmitted through air, hard-surfaced objects tend to reflect most of the ultrasonic energy, while soft surfaces tend to absorb the most energy. When the surfaces are stationary, the frequency of the waves detected by the receiver will be equal to the transmitted frequency. However, a change in frequency will occur as a result of the Doppler principle when a person or object is moving towards or away from the detector. Such an event initiates an alarm signal. This technology is not active in many properties as many consider this obsolete. Microwave detectors This device emits microwaves from a transmitter and detects any reflected microwaves or reduction in beam intensity using a receiver. The transmitter and receiver are usually combined inside a single housing (monostatic) for indoor applications and separate housings (bistatic) for the protection of outdoor perimeters high-risk sites and critical infrastructures such as fuel storage, petrochemical facilities, military sites, civil and military airports, nuclear facilities and more. To reduce false alarms this type of detector is usually combined with a passive infrared detector or similar alarm. Compared to the monostatic, the bistatic units work over longer distances: typical distances for transmitter-receivers up to 200m for X-band frequencies and up to 500m for K-band frequencies. detection system used to protect a solar farm Microwave detectors respond to a Doppler shift in the frequency of the reflected energy, by a phase shift, or by a sudden reduction of the level of received energy. Any of these effects may indicate motion of an intruder. Microwave detectors are low cost, easy to install, have an invisible perimeter barrier, and are not affected by fog, rain, snow, sand storms, or wind. May be affected by the presence of water dripping on the ground. Typically need a sterile clearance area to prevent partial blocking of the detection field. Functioning The microwave generator is equipped with an antenna that allows it to concentrate the beam of electromagnetic waves in one preferred location and the beam is intercepted by the receiver, equipped with a similar antenna to the transmitter. The graphical representation of the beam is similar to a cigar, and, when not disturbed, it runs between the transmitter and the receiver and generates a continuous signal. When an individual tries to cross this beam, it produces a disturbance that is caught by the receiver as a variation of amplitude of the received signal. These barriers are immune to harsh weather, such as fog, heavy rain, snow and sandstorms: none of these atmospheric phenomena affect in any way the behaviour and the reliability of the microwave detection. Furthermore, the working temperature range of this technology goes from -35 °C to +70 °C. Digital analysis of the signal The more recent and higher performance models of these detectors generate a detection whether the intruder is rolling, crossing, crawling or moving very slow within the electromagnetic field reducing false alarms. The ellipsoidal shape of the longitudinal section however does not allow a good detection capability close to the receiver or transmitter heads, and those areas are commonly referred to as "dead zones". A solution to avoid this problem, when installing 2 or more barriers, is to cross the respective transmitter and receiver heads some meters from the respective heads or to use mono-head sensor to cover the dead zones. On the contrary, capacitive-based accelerometers, also known as vibration sensors, rely on a change in electrical capacitance in response to acceleration. Operating principle The current technology allows to realize suspended silicon structures that are attached to the substrate in some points called anchors, and that constitute the sensitive mass of the accelerometer MEMS. These structures are free to move in the direction of the acceleration detected. They constitute the mobile reinforcement of a pair of capacitors connected to the half bridge. In this way, the acquired signals are amplified, filtered and converted in digital signals with the supervision of specific control circuits. MEMS' incorporations evolved from a single, stand-alone device to the integrated inertial motion units that are available today. This technology uses a variety of transduction mechanisms to detect the displacement. They include capacitive, piezoresistive, thermal, optical, piezoelectric and tunneling. Applications In the last decades, many technological progresses have been made in this area and MEMS accelerometers are used in high-reliability environments and are starting to replace other established technologies. MEMS accelerometer can be applied as a sensor in the earthquake disaster prevention, since one of the main characteristics of MEMS accelerometers is the linear frequency response to DC to about 500 Hz, and this capability offers an improvement in measuring ground motion at lower-frequency band. Another practical application of MEMS accelerometers is in machine condition monitoring to reduce machines' maintenance. Wireless and embedded technologies such as Micro-electro Mechanical system sensors offer a wireless smart vibration measurement of machine's condition. Ferrous metal detectors Change in the local magnetic field due to the presence of ferrous metals induces a current in the buried sensors (buried cables or discrete sensors) which are analyzed by the system. If the change exceeds a predetermined threshold, an alarm is generated. This type of sensor can be used to detect intruders carrying substantial amounts of metal, such as a firearm, making it ideally suited for anti-poaching applications. Electrostatic field Sometimes referred to as E-field, this volumetric sensor uses Electric field proximity sensing and can be installed on buildings, perimeters, fences, and walls. It also has the ability to be installed free-standing on dedicated poles. The system uses an electromagnetic field generator powering one wire, with another sensing wire running parallel to it. The sensing wire is connected to a signal processor that analyses amplitude change (mass of intruder), rate change (movement of intruder), and preset disturbance time (time the intruder is in the pattern). These items define the characteristics of an intruder and when all three are detected simultaneously, an alarm signal is generated. The barrier can provide vertical protection from the ground to the height of the mounting posts (typically 4–6meters of height), depending on the number of sensor wires installed. It is usually configured in zones of about 200 metre lengths. Electrostatic field sensors are high-security and difficult to defeat, and have high vertical detection field. However, these sensors are expensive and have short zones, which contributes to more electronics (and thus a higher cost). Microphonic systems Microphonic systems vary in design (for example, time-domain reflectrometer or piezo-electric) but each is generally based on the detection of an intruder attempting to cut or climb over a fence. Usually the microphonic detection systems are installed as sensor cables attached to rigid chain-wire fences, however, some specialized versions of these systems can also be installed buried underground. Depending on the type, it can be sensitive to different frequencies or levels of noise or vibration. The system is based on coaxial or electro-magnetic sensor cable with the controller having the ability to differentiate between signals from the cable or chain-wire being cut, an intruder climbing the fence, or bad weather conditions. The systems are designed to detect and analyze incoming electronic signals received from the sensor cable, and then to generate alarms from signals which exceed pre-set conditions. The systems have adjustable electronics to permit installers to change the sensitivity of the alarm detectors to the suit specific environmental conditions. The tuning of the system is usually done during commissioning of the detection devices. Microphonic systems are relatively inexpensive compared to other systems and easy to install, but older systems may have a high rate of false alarms caused by wind and other distances. Some newer systems use DSP to process the signal and reduce false alarms. Taut wire fence systems A taut wire perimeter security system is an independent screen of tensioned tripwires usually mounted on a fence or wall. Alternatively, the screen can be made thicker to avoid the need for a supporting chain-wire fence. These systems are designed to detect any physical attempt to penetrate the barrier. Taut wire systems can operate with a variety of switches or detectors that sense movement at each end of the tense wires. These switches or detectors can be a simple mechanical contact, static force transducer or an electronic strain gauge. Unwanted alarms caused by birds and other animals can be avoided by adjusting the sensors to ignore objects that exert small amounts of pressure on the wires. This type of system is vulnerable to intruders digging under the fence. A concrete footing directly below the fence is installed to prevent this type of attack. Taut wire fence systems have low false alarm rates, reliable sensors, and high detection rates, but is expensive and complicated to install. Fiber optic cable A fiber-optic cable can be used to detect intruders by measuring the difference in the amount of light sent through the fiber core. A variety of fiber optic sensing technologies may be used, including Rayleigh scattering or interferometry. If the cable is disturbed, the light will change and the intrusion is detected. The cable can be attached directly to a chain-wire fence or bonded into a barbed steel tape that is used to protect the tops of walls and fences. This type of barbed tape provides a good physical deterrent as well as giving an immediate alarm if the tape is cut or severely distorted. Being cable-based, fiber optic cables are very similar to the microphonic system and easy to install and can cover large perimeters. However, despite performing in a similar manner to microphonic-based systems, fiber optic cables have higher cost and is more complex due to the use of fiber-optic technology. Ported coaxial cable This system employs an electromagnetic field disturbance principle based on two coaxial cables. The transmitter emits continuous radio frequency (RF) energy along one cable and the energy is received by the other cable. When the change in field strength weakens due to the presence of an object and reaches a preset lower threshold, an alarm condition is generated. The system is covert after installation. The surrounding soil must offer good drainage in order to avoid nuisance alarms. Ported coaxial cables are concealed as a buried form but can be affected by RF noise and is difficult to install. Security electric fence Security electric fences consist of wires that carry pulses of electric current to provide a non-lethal shock to deter potential intruders. Tampering with the fence also results in an alarm that is logged by the security electric fence energiser, and can also trigger a siren, strobe, and/or notifications to a control room or directly to the owner via email or phone. In practical terms, security electric fences are a type of sensor array that acts as a (or part of a) physical barrier, a psychological deterrent to potential intruders, and as part of a security alarm system. Electric fences are less expensive than many other methods, less likely to give false alarms than many other alternative perimeter security methods, and have highest psychological deterrent of all methods, but there is a potential for unintended shock. ==Wired, wireless, and hybrid systems==

The trigger signal from sensors are transmitted to one or more control units either through wires or wireless means, such as radio, line carrier, and infrared. Wired systems are convenient when sensors, such as passive infrared motion sensors and smoke detectors require external power to operate correctly; however, they may be more costly to install. Basic wired systems utilize a star network topology, where the panel is at the center logically, and all devices home run their line wires back to the panel. More complex panels use a Bus network topology where the wire basically is a data loop around the perimeter of the facility, and has drops for the sensor devices which must include a unique device identifier integrated into the sensor device itself. Wired systems also have the advantage, if wired properly for example by dual loop, of being tamper-evident. Wireless systems, on the other hand, often use battery-powered transmitters which are easier to install and have less expensive start-up costs, but may fail if the batteries are not maintained. Depending on distance and construction materials, one or more wireless repeaters may be required to bring the signal to the alarm panel reliably. A wireless system can be moved to a new property easily. An important wireless connection for security is between the control panel and the monitoring station. Wireless monitoring of the alarm system protects against a burglar cutting cables or from failures of an internet provider. This setup is commonly referred to as fully wireless. Hybrid systems use both wired and wireless sensors to achieve the benefits of both. Transmitters can also be connected through the premises' electrical circuits to transmit coded signals to the control unit (line carrier). The control unit usually has a separate channel or zone for burglar and fire sensors, and more advanced systems have a separate zone for every different sensor, as well as internal trouble indicators, such as mains power loss, low battery, and broken wires. ==Alarm connection and monitoring==

Depending upon the application, the alarm output may be local, remote or a combination of both. Local alarms do not include monitoring, but may include indoor and/or outdoor sounders, such as motorized bells or electronic sirens and lights, such strobe lights which may be useful for signaling an evacuation notice during fire emergencies, or to scare off an amateur burglar quickly. However, with the widespread use of alarm systems, especially in cars, false alarms are very frequent and many urbanites tend to ignore alarms rather than investigating, and not contacting the necessary authorities. In rural areas where not many may hear the fire bell or burglar siren, lights or sounds may not make much difference, as the nearest emergency responders may arrive too late to avoid losses. Remote alarm systems are used to connect the control unit to a predetermined monitor of some sort, and they are available in many different configurations. Advanced systems connect to a central station or first responder (e.g. police/fire/medical) via a direct phone wire, a cellular network, a radio network, or an IP path. In the case of a dual signaling system two of these options are utilized simultaneously. The alarm monitoring includes not only the sensors, but also the communication transmitter itself. While direct phone circuits are still available in some areas from phone companies, because of their high cost and the advent of dual signaling with its comparatively lower cost, their use is being phased out. Direct connections are now most usually seen only in federal, state, and local government buildings, or on a school campus that has a dedicated security, police, fire, or emergency medical department. In the United Kingdom, communication is only possible to an alarm receiving centre, and communication directly to the emergency services is not permitted. More typical systems incorporate a digital cellular communication unit that will contact the central station or a monitoring station via the Public Switched Telephone Network (PSTN) and raise the alarm, either with a synthesized voice or increasingly via an encoded message string that the central station decodes. These may connect to the regular phone system on the system side of the demarcation point, but typically connect on the customer side ahead of all phones within the monitored premises so that the alarm system can seize the line by cutting-off any active calls and call the monitoring company if needed. A dual signaling system would raise the alarm wirelessly via a radio path or cellular path using the phone line or broadband line as a backup overcoming any compromise to the phone line. Encoders can be programmed to indicate which specific sensor was triggered, and monitors can show the physical location of the sensor on a list or even a map of the protected premises, which can make the resulting response more effective. Many alarm panels are equipped with a backup communication path for use when the primary PSTN circuit is not functioning. The redundant dialer may be connected to a second communication path, or a specialized encoded cellular phone, radio, or internet interface device to bypass the PSTN entirely, to thwart intentional tampering with the phone lines. Tampering with the line could trigger a supervisory alarm via the radio network, giving early warning of an imminent problem. In some cases a remote building may not have PSTN phone service, and the cost of trenching and running a direct line may be prohibitive. It is possible to use a wireless cellular or radio device as the primary communication method. In the UK, the most popular solution of this kind is similar in principle to the above but with the primary and backup paths reversed. Utilizing a radio path as the primary signaling path is not only quicker than PSTN but also allows significant cost savings as unlimited amounts of data can be sent at no extra expense. ==Broadband alarm monitoring==

Increasing deployment of voice over IP technology (VoIP) is driving the adoption of broadband signaling for alarm reporting. Many sites requiring alarm installations no longer have conventional telephone lines (POTS), and alarm panels with conventional telephone dialer capability do not work reliably over some types of VoIP service. Dial-up analogue alarm panels or systems with serial/parallel data ports may be migrated to broadband through the addition of an alarm server device which converts telephone signaling signals or data port traffic to IP messages suitable for broadband transmission. However, the direct use of VoIP to transport analogue alarms without an alarm server device is problematic as the audio codecs used throughout the entire network transmission path cannot guarantee a suitable level of reliability or quality of service acceptable for the application. In response to the changing public communications network, new alarm systems often use broadband signaling as a method of alarm transmission, and manufacturers are including IP reporting capability directly in their alarm panel products. When the Internet is used as a primary signaling method for critical security and life safety applications, frequent supervision messages are configured to overcome concerns about backup power for network equipment and signal delivery time. But for typical applications, connectivity concerns are controlled by normal supervision messages. ==Radio alarm dual signaling==

Dual signaling is a method of alarm transmission that uses a mobile phone network and a telephone and/or IP path to transmit intruder, fire and personal attack signals at high speed from the protected premises to an Alarm Receiving Centre (ARC). It most commonly uses GPRS or GSM, a high-speed signaling technology used to send and receive 'packets' of data, with a telephone line in addition. IP is not used as frequently due to issues with installation and configuration as high levels of expertise is often required in addition to alarm installation knowledge. Modern alarm communicators have largely transitioned from 2G GPRS to 4G LTE cellular modules, providing faster signal delivery and improved reliability, particularly as 2G networks have been progressively decommissioned across Europe and North America. A dual signaling communication device is attached to a control panel on a security installation and is the component that transmits the alarm to the ARC. It can do this in a number of different ways, via the GPRS radio path, via the GSM radio path or via the telephone line/or IP. These multiple signaling paths are all present and live at the same time backing each other up to minimize exposure of the property to intruders. Should one fail, there is always a back up and depending on the manufacturer chosen up to three paths working simultaneously at any one time. Dual paths allow distinction between hardware failures and a genuine attack on the alarm. This helps eliminate false alarms and unnecessary responses. Dual signaling has helped considerably with the restoration of police response as in an instance where a phone line is cut as the dual signaling device can continue to send alarm calls via one of its alternative paths either confirming or denying the alarm from the initial path. In the UK, CSL DualCom Ltd pioneered dual signaling in 1996. The company offered an alternative to existing alarm signaling while setting the current standard for professional dual path security monitoring. Dual signaling is now firmly regarded as the standard format for alarm signaling and is duly specified by all of the leading insurance companies. ==Listen-in alarm monitoring==

Monitored alarms and speaker phones allow for the central station to speak with the homeowner or intruder. This may be beneficial to the owner for medical emergencies. For actual break-ins, the speaker phones allow the central station to urge the intruder to cease and desist as response units have been dispatched. Listen-in alarm monitoring is also known as Immediate Audio-Response monitoring or Speaking Alarm Systems in the UK. ==Alarm response==

In the United States, police respond to at least 36million alarm activations each year, at an estimated annual cost of $1.8billion. Depending upon the zone triggered, number and sequence of zones, time of day, and other factors, the alarm monitoring center may automatically initiate various actions. Central station operators might be instructed to call emergency services immediately, or to first call the protected premises or property manager to try to determine if the alarm is genuine. Operators could also start calling a list of phone numbers provided by the customer to contact someone to go check on the protected premises. Some zones may trigger a call to the local heating oil company to check on the system, or a call to the owner with details of which room may be flooded. Some alarm systems are tied to video surveillance systems so that current video of the intrusion area can be instantly displayed on a remote monitor and recorded. Some alarm systems use real-time audio and video monitoring technology to verify the legitimacy of an alarm. In some municipalities around the United States, this type of alarm verification allows the property it is protecting to be placed on a "verified response" list, allowing for quicker and safer police responses. ==Access control and bypass codes==

To be useful, an intrusion alarm system is deactivated or reconfigured when authorized personnel are present. Authorization may be indicated in any number of ways, often with keys or codes used at the control panel or a remote panel near an entry. High-security alarms may require multiple codes, or a fingerprint, badge, hand-geometry, retinal scan, encrypted-response generator, and other means that are deemed sufficiently secure for the purpose. Failed authorizations would result in an alarm or a timed lockout to prevent experimenting with possible codes. Some systems can be configured to permit deactivation of individual sensors or groups. Others can also be programmed to bypass or ignore individual sensors and leave the remainder of the system armed. This feature is useful for permitting a single door to be opened and closed before the alarm is armed, or to permit a person to leave, but not return. High-end systems allow multiple access codes, and may only permit them to be used once, or on particular days, or only in combination with other users' codes (i.e., escorted). In any case, a remote monitoring center should arrange an oral code to be provided by an authorized person in case of false alarms, so the monitoring center can be assured that a further alarm response is unnecessary. As with access codes, there can also be a hierarchy of oral codes, for example, for furnace repairperson to enter the kitchen and basement sensor areas but not the silver vault in the pantry. There are also systems that permit a duress code to be entered and silence the local alarm, but still trigger the remote alarm to summon the police to a robbery. Fire sensors can be isolated, meaning that when triggered, they will not trigger the main alarm network. This is important when smoke and heat is intentionally produced. The owners of buildings can be fined for generating false alarms that waste the time of emergency personnel. ==False and absent alarms==

The United States Department of Justice estimates that between 94% and 98% of all alarm calls to law enforcement are false alarms. Nuisance alarms occur when an unintended event evokes an alarm status by an otherwise properly working alarm system. A false alarm also occurs when there is an alarm system malfunction that results in an alarm state. In all three circumstances, the source of the problem should be immediately found and fixed, so that responders will not lose confidence in the alarm reports. It is easier to know when there are false alarms, because the system is designed to react to that condition. Failure alarms are more troublesome because they usually require periodic testing to make sure the sensors are working and that the correct signals are getting through to the monitor. Some systems are designed to detect problems internally, such as low or dead batteries, loose connections, phone circuit trouble, etc. While earlier nuisance alarms could be set off by small disturbances, like insects or pets, newer model alarms have technology to measure the size/weight of the object causing the disturbance, and thus are able to decide how serious the threat is, which is especially useful in burglar alarms. Some municipalities across the United States require alarm verification before police are dispatched. Under this approach, alarm monitoring companies must verify the legitimacy of alarms (except holdup, duress, and panic alarms) before calling the police. Verified response typically involves visual on-scene verification of a break-in, or remote audio or video verification. ==Audio and video verification==

Alarms that utilize audio, video, or combination of both audio and video verification technology give security companies, dispatchers, police officers, and property managers more reliable data to assess the threat level of a triggered alarm. Audio and video verification techniques use microphones and cameras to record audio frequencies, video signals, or image snapshots. The source audio and video streams are sent over a communication link, usually an Internet protocol (IP) network, to the central station where monitors retrieve the images through proprietary software. The information is then relayed to law enforcement and recorded to an event file, which can be used to plan a more strategic and tactical approach of a property, and later as prosecution evidence. An example of this system is when a passive infrared or other sensor is triggered a designated number of video frames from before and after the event is sent to the central station. A second video solution can be incorporated into a standard panel, which sends the central station an alarm. When a signal is received, a trained monitoring professional accesses the on-site digital video recorder (DVR) through an IP link to determine the cause of the activation. For this type of system, the camera input to the DVR reflects the alarm panel's zones and partitioning, which allows personnel to look for an alarm source in multiple areas. The United States Department of Justice states that legislation requiring alarm companies to verify the legitimacy of an alarm, before contacting law enforcement (commonly known as "verified response") is the most effective way to reduce false burglar alarms. The Department of Justice considers audio, video, or an eye-witness account as verification for the legitimacy of a burglar alarm. ==Cross-zoning==

Cross-zoning is a strategy that uses multiple sensors to monitor activity in one area and software analyses input from all the sources. For example, if a motion detector trips in one area, the signal is recorded and the central-station monitor notifies the customer. A second alarm signal—received in an adjacent zone within a short time—is the confirmation the central-station monitor needs to request a dispatch immediately. This method builds increased protection. ==Enhanced call verification==

Enhanced call verification (ECV) helps reduce false dispatches while still protecting citizens, and is mandated in several US jurisdictions, although the alarm industry has successfully opposed it in others. ECV requires central station personnel to attempt to verify the alarm activation by making a minimum of two phone calls to two different responsible party telephone numbers before dispatching law enforcement to the scene. The first alarm-verification call goes to the location the alarm originated. If contact with a person is not made, a second call is placed to a different number. The secondary number, best practices dictate, should be to a telephone that is answered even after hours, preferably a cellular phone of a decision maker authorized to request or bypass emergency response. ECV, as it cannot confirm an actual intrusion event and will not prompt a priority law enforcement dispatch, is not considered true alarm verification by the security industry. ==Independent certification==

Some insurance companies and local agencies require that alarm systems be installed to code or be certified by an independent third party. The alarm system is required to have a maintenance check carried out every 6 – 12 months. In the UK, 'Audible Only' intruder alarm systems require a routine service visit once every 12 months and monitored intruder alarm systems require a check twice in every 12-month period. This is to ensure all internal components, sensors and PSUs are functioning correctly. In the past, this would require an alarm service engineer to attend site and carry the checks out. With the use of the Internet or radio path and a compatible IP/radio transmitting device (at the alarmed premises), some checks can now be carried out remotely from the central station. ==See also==