Bypass ratio

powering the Airbus A350, having its core and its bypass duct observable from this view. If all the gas power from a gas turbine is converted to kinetic energy in a propelling nozzle, the aircraft is best suited to high supersonic speeds. If it is all transferred to a separate large mass of air with low kinetic energy, the aircraft is best suited to zero speed (hovering). For speeds in between, the gas power is shared between a separate airstream and the gas turbine's own nozzle flow in a proportion which gives the aircraft performance required. The first jet aircraft were subsonic and the poor suitability of the propelling nozzle for these speeds due to high fuel consumption was understood, and bypass proposed, as early as 1936 (U.K. Patent 471,368). The underlying principle behind bypass is trading exhaust velocity for extra mass flow which still gives the required thrust but uses less fuel. Turbojet inventor Frank Whittle called it "gearing down the flow". Power is transferred from the gas generator to an extra mass of air, i.e. a larger diameter propelling jet, moving more slowly. The bypass spreads the available mechanical power across more air to reduce the velocity of the jet. The trade-off between mass flow and velocity is also seen with propellers and helicopter rotors by comparing disc loading and power loading. For example, the same helicopter weight can be supported by a high power engine and small diameter rotor or, for less fuel, a lower power engine and bigger rotor with lower velocity through the rotor. Bypass usually refers to transferring gas power from a gas turbine to a bypass stream of air to reduce fuel consumption and jet noise. Alternatively, there may be a requirement for an afterburning engine where the sole requirement for bypass is to provide cooling air. This sets the lower limit for BPR and these engines have been called "leaky" or continuous bleed turbojets (General Electric YJ-101 BPR 0.25) and low BPR turbojets (Pratt & Whitney PW1120). Low BPR (0.2) has also been used to provide surge margin as well as afterburner cooling for the Pratt & Whitney J58. ==Description==

In a zero-bypass (turbojet) engine the high temperature and high pressure exhaust gas is accelerated by expansion through a propelling nozzle and produces all the thrust. The compressor absorbs all the mechanical power produced by the turbine. In a bypass design, extra turbines drive a ducted fan that accelerates air rearward from the front of the engine. In a high-bypass design, the ducted fan and nozzle produce most of the thrust. Turbofans are closely related to turboprops in principle because both transfer some of the gas turbine's gas power, using extra machinery, to a bypass stream leaving less for the hot nozzle to convert to kinetic energy. Turbofans represent an intermediate stage between turbojets, which derive all their thrust from exhaust gases, and turbo-props which derive minimal thrust from exhaust gases (typically 10% or less). Extracting shaft power and transferring it to a bypass stream introduces extra losses which are more than made up by the improved propulsive efficiency. The turboprop at its best flight speed gives significant fuel savings over a turbojet even though an extra turbine, a gearbox and a propeller were added to the turbojet's low-loss propelling nozzle. The turbofan has additional losses from its extra turbines, fan, bypass duct and extra propelling nozzle compared to the turbojet's single nozzle. To see the influence of increasing BPR alone on overall efficiency in the aircraft, i.e. SFC, a common gas generator has to be used, i.e. no change in Brayton cycle parameters or component efficiencies. Bennett shows in this case a relatively slow rise in losses transferring power to the bypass at the same time as a fast drop in exhaust losses with a significant improvement in SFC. In reality increases in BPR over time come along with rises in gas generator efficiency masking, to some extent, the influence of BPR. Only the limitations of weight and materials (e.g., the strengths and melting points of materials in the turbine) reduce the efficiency at which a turbofan gas turbine converts this thermal energy into mechanical energy, for while the exhaust gases may still have available energy to be extracted, each additional stator and turbine disk retrieves progressively less mechanical energy per unit of weight, and increasing the compression ratio of the system by adding to the compressor stage to increase overall system efficiency increases temperatures at the turbine face. Nevertheless, high-bypass engines have a high propulsive efficiency because even slightly increasing the velocity of a very large volume and consequently mass of air produces a very large change in momentum and thrust: thrust is the engine's mass flow (the amount of air flowing through the engine) multiplied by the difference between the inlet and exhaust velocities in—a linear relationship—but the kinetic energy of the exhaust is the mass flow multiplied by one-half the square of the difference in velocities. A low disc loading (thrust per disc area) increases the aircraft's energy efficiency, and this reduces the fuel use. powering the Boeing 787 Dreamliner, with the hot exhaust observable flowing from the engine's core The Rolls–Royce Conway turbofan engine, developed in the early 1950s, was an early example of a bypass engine. The configuration was similar to a 2-spool turbojet but to make it into a bypass engine it was equipped with an oversized low pressure compressor: the flow through the inner portion of the compressor blades went into the core while the outer portion of the blades blew air around the core to provide the rest of the thrust. The bypass ratio for the Conway varied between 0.3 and 0.6 depending on the variant The growth of bypass ratios during the 1960s gave jetliners fuel efficiency that could compete with that of piston-powered planes. Today (2015), most jet engines have some bypass. Modern engines in slower aircraft, such as airliners, have bypass ratios up to 12:1; in higher-speed aircraft, such as fighters, bypass ratios are much lower, around 1.5; and craft designed for speeds up to Mach 2 and somewhat above have bypass ratios below 0.5. Turboprops have bypass ratios of 50-100, although the propulsion airflow is less clearly defined for propellers than for fans and propeller airflow is slower than the airflow from turbofan nozzles. Engine bypass ratios , which had a BPR lower than 1. showing the relative sizes of core exhaust and bypass duct for a BPR of 5.5. showing the relative areas for bypass and core flow for a 12:1 bypass ratio. ==See also==