Cutter (boat)

chasing a French cutter in 1781 The term cutter appeared in the early 18th century as a description of a hull type. These vessels were designed for speed and the name was used in a similar way to clipper in the next century. The concept of hull type was perpetuated by the term "cutter brig" which was used over the period circa 1781–1807 for those rigged as brigs. "Cutter built" was a description applied to a hull of this type and designed for speed. More generally, the unmodified word "cutter" soon became associated with a single-masted rig. Fast vessels were often used for illegal purposes, such as smuggling, or by the authorities trying to prevent this illegality. Therefore, cutters were used for both. The Royal Navy bought and had built a large number for use in controlling smuggling, as "advice boats" (carrying dispatches), or against privateers. The characteristic cutter hull shape was wide; many had a length to breadth ratio of 3 to 1. It had a lot of deadrise and fine lines. A huge amount of sail could be set on these beamy hulls. The rig became standardised as having one mast, a gaff-rigged mainsail, square sails and several headsailstogether with a full range of extra light weather sails. The mainsail had a boom that extended beyond the stern. Square sails consisted of a course, topsail and topgallant. In earlier examples (before 1800) the topsail's foot had a large amount of roach and was sheeted to a separate yard that was set below the main yard (which carried the course). The headsails were a staysail, set on the forestay (which fastened to the stemhead), a jib, set flying to a traveller on the bowsprit and, in most cases, a flying jib (alternatively termed a jib-topsail) also set flying, but to a higher point on the mast. A cutter has a running bowsprit, which can be brought inboard when not needed, such as in rough weather or in harbour. The bowsprit was usually of great length, sometimes longer than the hull. The standard fair weather sails consisted of a ringtail to the mainsail and studding sails to the square sails. It was not unknown for cutters to use a removable mizzen mast for use when reaching, setting a lugsail. Since the boom of the mainsail overhung the stern, the mast would have to be removed to tack or gybe. The dimensions of an 18th-century cutter purchased by the Royal Navy in 1763, and roughly in the middle of the size range of the batch of 30 bought that year () are: length on deck , beam , measuring just over 78 tons bm. Smuggling cutters ranged from 30 tons (captured in 1747) to 140 tons. The Revenue cutters increased in size to match the vessels they attempted to catchRepulse, of 210 tons was built in 1778. A determining factor on size was the number of crew needed to handle the large gaff mainsail with its long boom. Larger cutters purchased by the Royal Navy were sometimes converted to brigs to make them easier to handle, but still utilising the fast hull. ==Ship's boat==

At about the same time that the decked, fast-sailing cutters of the 18th century appeared, the term was also applied to a new class of ship's boat. These were clinker-built open boats, optimised for sailing but capable under oars. They had finer lines than the boats of that time (which had more rounded bows) and a transom stern. A distinctive feature was that the washstrake had cut-outs (called rowlocks) in which the oars were worked, unlike most boats of the period, that used thole pins as the pivot point for the oars. This allowed a higher freeboard, which was helpful if sailingwhen the cut-outs were filled with wooden shutters (often mis-called poppets) to keep the water out. The alternative, if the correct geometry for an efficient rowing position was adopted, was to position the thwarts awkwardly high. Like some other types of ship's boats used in the Royal Navy, the cutter appears to have originated in Deal. Some Navy Board correspondence of 1712 concerns disapproval of the captain of for buying a cutter of about in length as a replacement for her pinnace. In 1722, another ship had a cutter issued for a voyage to India, and by 1740 substantial numbers of cutters were being bought from Deal boatbuilders to equip Navy ships. The size of these boats varied from in length. The 1740 purchases coincided with a decision to increase the number of boats carried by warships. During the Seven Years' War cutters were found particularly useful for cruising ships, being seaworthy and useful for boarding. However, they were more susceptible to damage than the heavier boats that they replaced and much less capable of carrying heavy weights, such as anchors and water casks. The range of sizes available steadily increased. By 1817 the cutters issued came in 17 different lengths, from . This big variety was reduced when the Royal Navy's warships moved to steam propulsion. Since drinking water could now be distilled on board, ships no longer needed to have the largest boats that they could carry to maximise the amount of water collected on each trip. The standard-issue cutters from 1877 to 1900 came in 11 different lengths, ranging from . In 1914 this was cut to 5 sizes, ranging from . The sailing rig of the cutters used as ship's boats was usually two masted. In 1761, the larger Deal-built cutters had spritsails set on these masts, soon transitioning to a dipping lug fore-sail and a sprit mizzen. For much of the 19th century, and into the 20th, cutters were rigged with a dipping lug on the foremast and a standing lug on the mizzen. This made them similar to many of the luggers worked from the beaches and harbours of Britain. The sail plan illustration here (1880 Sail Plan) even replicates the civilian lugger terminology of having a fore and mizzen mast, and not using the term "main mast". A variation on this rig, seen for example in 1887, was to have two dipping lugs. The number of oars pulled varied with the size of the boat. A schedule of ship's boats of 1886 shows cutters pulling 12 oars, , 10 oars, , 8 oars and the two smallest sizes of , 6 oars. The smaller boats could be single banked whilst the larger and later examples were generally double-banked. For transporting large numbers of men, in moderate weather conditions, a 34 ft cutter could carry a total of 66 men, a 26 ft cutter, 36 men and a 20 ft cutter, 21 men. Steam powered ship's boats saw a slow introduction to the Royal Navy from 1864. By 1877, three types were in use: steam launches, picket boats and steam cutters. However, right up to the time of the First World War, the majority of the boats in use continued to be propelled solely by sail and oar. The Royal Navy still has some cutters that can be worked under sail or oar. ==Sailing rig==

In the simpler definition, the sailing rig called "cutter" has a single mast with fore and aft sails which include more than one headsail. The mainsail (set abaft, or behind the mast) could be gaff, Bermuda, standing lug or gunter rigged. A more complex definition may be applied in American waters, where a boat with two headsails would be termed a sloop if the mast has a more forward position and the bowsprit is permanently rigged. An example of this is the Friendship Sloop. A traditional cutter, by contrast, has a running bowsprit and the jib is set flying on a traveller that is hauled out to the end of the bowsprit. In a vessel such as a Bristol Channel Pilot Cutter, a storm jib might be set on a reefed bowsprit, with the bowsprit partially run in from its most fully extended position. ==Other types==

Rowing The watermen of London used similar boats in the 18th century often decorated as depicted in historical prints and pictures of the River Thames in the 17th and 18th centuries. The modern waterman's cutter is based on drawings of these boats. They are long with a beam of . They can have up to six oarsmen either rowing or sculling and can carry a cox and passengers. The organisers of the Great River Race developed the modern version in the 1980s and now many of the fleet of 24 compete annually in a "Marathon of the River". Watermen's cutters also compete annually in the Port of London Challenge, and the Port Admirals' Challenge. Cutter races are also to be found at various town rowing and skiffing regattas. In addition the cutters perform the role of ceremonial Livery Barges with the canopies and armorial flags flying on special occasions. Cutters have been used for record-breaking attempts and crews have achieved record times for sculling the English Channel (2 h 42 min) in 1996 and for sculling non-stop from London to Paris (4 days 15 min) in 1999. Events have been held with multiple teams attempting these challenges. Pilot The pilot cutter developed from the need for a fast boat to take maritime pilots from harbour to incoming large trading vessels. As most early pilots were local fisherman who undertook both jobs, although licensed by the harbour to operate within their jurisdiction, pilots were generally self-employed, and the quickest transport meant greater income. As their fishing boats were heavy working boats, and filled with fishing equipment, they needed a new type of boat; early boats were developed from single masted fishing cutter designs and twin masted yawls, and latterly into the specialist pilot cutter. The natural dangers of the Bristol Channel brought about over many years the development of the specialist Bristol Channel Pilot Cutter. According to records from Pill, Somerset now housed in the Bristol Museum, the first official Bristol Channel pilot was barge master George James Ray, appointed by the Corporation of Bristol in May 1497 to pilot John Cabot's from Bristol harbour to the open sea beyond. In 1837 Pilot George Ray guided Brunel's , and in 1844 William Ray piloted the larger on her maiden voyage. Customs services The term cutter is also used for any seaworthy vessel used in the law enforcement duties of the United Kingdom's Border Force, the United States Coast Guard (because of its descent from the United States Revenue Cutter Service) or the customs services of other countries. In the United States, the early Revenue Cutter Service operated customs cutters that were commonly schooners or brigs. In Britain, they were usually rigged as defined under Sailing (above). The British Board of Customs also used other vessels as hulks, which were moored in places such as tidal creeks. Customs officers worked from the hulks in smaller boats. In the UK, the Border Force (successor to the UK Border Agency and HM Customs and Excise) currently operates a fleet of 42 m corvette-type vessels throughout UK territorial waters as border cutters, inspecting vessels for illicit cargoes. Image:USCGC Hamilton (WHEC-715).jpg|"High Endurance Cutter" Image:Bundesarchiv Bild 183-08328-0004, Berlin, Jachtwerft Berlin, Fischkutter.jpg|German Fishcutter, Jachtwerft, Köpenick, Berlin, 1950 Image:Stan Patrol P810 Jaguar Dutch Caribbean Coastguard.jpg|Dutch Caribbean Coast Guard cutter Jaguar ==See also==