Internet Protocol

to a link protocol frame The Internet Protocol is responsible for addressing host interfaces, encapsulating data into datagrams (including fragmentation and reassembly) and routing datagrams from a source host interface to a destination host interface across one or more IP networks.'''''' For these purposes, the Internet Protocol defines the format of packets and provides an addressing system. Each datagram has two components: a header and a payload. The IP header includes a source IP address, a destination IP address, and other metadata needed to route and deliver the datagram. The payload is the data that is transported. This method of nesting the data payload in a packet with a header is called encapsulation. IP addressing entails the assignment of IP addresses and associated parameters to host interfaces. The address space is divided into subnets, involving the designation of network prefixes. IP routing is performed by all hosts, as well as routers, whose main function is to transport packets across network boundaries. Routers communicate with one another via specially designed routing protocols, either interior gateway protocols or exterior gateway protocols, as needed for the topology of the network. ==Addressing methods==

There are four principal addressing methods in the Internet Protocol: == Version history ==

, PRNET, and SATNET on November 22, 1977 In May 1974, the Institute of Electrical and Electronics Engineers (IEEE) published a paper entitled "A Protocol for Packet Network Intercommunication". The paper's authors, Vint Cerf and Bob Kahn, described an internetworking protocol for sharing resources using packet switching among network nodes. A central control component of this model was the Transmission Control Program that incorporated both connection-oriented links and datagram services between hosts. The monolithic Transmission Control Program was later divided into a modular architecture consisting of the Transmission Control Protocol and User Datagram Protocol at the transport layer and the Internet Protocol at the internet layer. The model became known as the Department of Defense (DoD) Internet Model and Internet protocol suite, and informally as TCP/IP. The following Internet Experiment Note (IEN) documents describe the evolution of the Internet Protocol into the modern version of IPv4: • IEN 2 Comments on Internet Protocol and TCP (August 1977) describes the need to separate the TCP and Internet Protocol functionalities (which were previously combined). It proposes the first version of the IP header, using 0 for the version field. • IEN 26 A Proposed New Internet Header Format (February 1978) describes a version of the IP header that uses a 1-bit version field. • IEN 28 Draft Internetwork Protocol Description Version 2 (February 1978) describes IPv2. • IEN 41 Internetwork Protocol Specification Version 4 (June 1978) describes the first protocol to be called IPv4. The IP header is different from the modern IPv4 header. • IEN 44 Latest Header Formats (June 1978) describes another version of IPv4, also with a header different from the modern IPv4 header. • IEN 54 Internetwork Protocol Specification Version 4 (September 1978) is the first description of IPv4 using the header that would become standardized in 1980 as . • IEN 80 • IEN 111 • IEN 123 • IEN 128/RFC 760 (1980) IP versions 1 to 3 were experimental versions, designed between 1973 and 1978. Versions 2 and 3 supported variable-length addresses ranging between 1 and 16 octets (between 8 and 128 bits). An early draft of version 4 supported variable-length addresses of up to 256 octets (up to 2048 bits) but this was later abandoned in favor of a fixed-size 32-bit address in the final version of IPv4. This remains the dominant internetworking protocol in use in the Internet Layer; the number 4 identifies the protocol version, carried in every IP datagram. IPv4 is defined in (1981). Version number 5 was used by the Internet Stream Protocol, an experimental streaming protocol that was not adopted. with over 41% of Google's traffic being carried over IPv6 connections. The assignment of the new protocol as IPv6 was uncertain until due diligence assured that IPv6 had not been used previously. Other Internet Layer protocols have been assigned version numbers, such as 7 (IP/TX), 8 and 9 (historic). Notably, on April 1, 1994, the IETF published an April Fools' Day RfC about IPv9. IPv9 was also used in an alternate proposed address space expansion called TUBA. A 2004 Chinese proposal for an IPv9 protocol appears to be unrelated to all of these, and is not endorsed by the IETF. IP version numbers ==Reliability==

The design of the Internet protocol suite adheres to the end-to-end principle, a concept adapted from the CYCLADES project. Under the end-to-end principle, the network infrastructure is considered inherently unreliable at any single network element or transmission medium and is dynamic in terms of the availability of links and nodes. No central monitoring or performance measurement facility exists that tracks or maintains the state of the network. For the benefit of reducing network complexity, the intelligence in the network is located in the end nodes. As a consequence of this design, the Internet Protocol only provides best-effort delivery and its service is characterized as unreliable. In network architectural parlance, it is a connectionless protocol, in contrast to connection-oriented communication. Various fault conditions may occur, such as data corruption, packet loss and duplication. Because routing is dynamic, meaning every packet is treated independently, and because the network maintains no state based on the path of prior packets, different packets may be routed to the same destination via different paths, resulting in out-of-order delivery to the receiver. All fault conditions in the network must be detected and compensated for by the participating end nodes. The upper layer protocols of the Internet protocol suite are responsible for resolving reliability issues. For example, a host may buffer network data to ensure correct ordering before the data is delivered to an application. IPv4 provides safeguards to ensure that the header of an IP packet is error-free. A routing node discards packets that fail a header checksum test. Although the Internet Control Message Protocol (ICMP) provides notification of errors, a routing node is not required to notify either end node of errors. IPv6, by contrast, operates without header checksums, since current link layer technology is assumed to provide sufficient error detection. ==Link capacity and capability==

The dynamic nature of the Internet and the diversity of its components provide no guarantee that any particular path is actually capable of, or suitable for, performing the data transmission requested. One of the technical constraints is the size of data packets possible on a given link. Facilities exist to examine the maximum transmission unit (MTU) size of the local link and Path MTU Discovery can be used for the entire intended path to the destination. The IPv4 internetworking layer automatically fragments a datagram into smaller units for transmission when the link MTU is exceeded. IP provides re-ordering of fragments received out of order. An IPv6 network does not perform fragmentation in network elements, but requires end hosts and higher-layer protocols to avoid exceeding the path MTU. The Transmission Control Protocol (TCP) is an example of a protocol that adjusts its segment size to be smaller than the MTU. The User Datagram Protocol (UDP) and ICMP disregard MTU size, thereby forcing IP to fragment oversized datagrams. ==Security==

During the design phase of the ARPANET and the early Internet, the security aspects and needs of a public, international network were not adequately anticipated. Consequently, many Internet protocols exhibited vulnerabilities highlighted by network attacks and later security assessments. In 2008, a thorough security assessment and proposed mitigation of problems was published. The IETF has been pursuing further studies. ==See also==