Juno I

Developed as a part of the Explorer Project, the original goal for the launch vehicle was to place an artificial satellite into orbit. Following the Soviet Union's launch of Sputnik 1 on October 4, 1957 (and the resulting "Sputnik crisis") and the failure of the Vanguard 1 launch attempt, the program received funding to match the Soviet space achievements. The launch vehicle family name was suggested in November 1957 by Jet Propulsion Laboratory (JPL) Director Dr. William Pickering, who proposed the name Juno, after the Roman goddess and queen of the gods, as well as for its position as the satellite-launching version of the Jupiter-C. The fourth stage for the Juno I launch vehicle was derived following the September 1956 test launch of a Jupiter-C for the Army Ballistic Missile Agency, which could have been the world's first satellite launch, had a fourth stage been loaded and fueled. A fourth stage would have allowed the nose cone to overshoot the target and enter orbit. The first launch of a Juno I launch vehicle was in early 1958, with the successful launch of Explorer 1 satellite on February 1, 1958, at 03:47:56 GMT, after the Soviet Union's Sputnik 1 on October 4, 1957. == Launch vehicle ==

The Juno I consisted of a Jupiter-C first stage, based on the Redstone missile; with three additional solid fuel stages based on the Sergeant missile to provide the added impulse to achieve orbit. The fourth stage was mounted on top of the "tub" of the third stage, and fired after third-stage burnout to boost the payload and fourth stage to an orbital velocity of , with an acceleration of 25–51 g. The tub along with the fourth stage were set spinning while the launch vehicle was on the launch pad to provide gyroscopic force in lieu of a guidance system that would have required thrust vectoring, vernier thrusters, or a reaction control system. The booster guidance package (with the tub attached) separated from the first stage after burnout to provide attitude control until second stage ignition. This multi-stage system, designed by Wernher von Braun in 1956 for his proposed Project Orbiter, obviated the need for a guidance system in the upper stages. It was the simplest method for putting a payload into orbit but having no upper-stage guidance, the payload could not achieve a precise orbit. Both the four-stage Juno I and three-stage Jupiter-C launch vehicles were the same height (), with the added fourth-stage booster of the Juno I being enclosed inside the nose cone of the third stage. == Launch history ==

Juno I was launched six times by Army Ballistic Missile Agency (ABMA) in 1958, intending to place satellites in low Earth orbit. giving the Juno I vehicle a mission total success ratio of 50%. The American public was happy and relieved that America had finally managed to launch a satellite after the launch failures in the Vanguard and Viking series. With the relative success of the Juno I program, von Braun developed the Juno II, using a PGM-19 Jupiter first stage, rather than a Redstone. Gallery File:Launch of Jupiter C with Explorer 1.jpg|Juno I RS-29 UE launching Explorer 1 File:Juno-1 explorer-2.jpg|Juno I RS-26 UV launching Explorer 2 File:Explorer III.jpg|Juno I RS-24 UT launching Explorer 3 File:Juno-1 (Explorer 4).jpg|Juno I RS-44 TT with Explorer 4 File:Juno-1 44.JPG|Juno I RS-44 TT launching Explorer 4 File:Juno I with Beacon 1.jpg|Juno I RS-49 HE with BEACON 1 File:Juno I RS CC-49.jpg|Juno I RS-49 HE launching BEACON 1 == On display ==

Juno I are displayed at: • Kennedy Space Center rocket garden, with Explorer 1 mock-up • National Air and Space Museum, labeled as Jupiter-C but with a Explorer 1 mock-up File:Juno I with Explorer I mock-up at KSC.jpg|Juno I at the Kennedy Space Center rocket garden File:NationalAirAndSpaceMuseum 10290004.jpg|Juno I at the National Air and Space Museum == See also ==