Lock and key

, India, 10th century Premodern history Gothic lock, from the 15th–16th centuries, made of iron, in the Metropolitan Museum of Art (New York City) Locks have been in use for over 6000 years, with one early example discovered in the ruins of Nineveh, the capital of ancient Assyria. Locks such as this were developed into the Egyptian wooden pin lock, which consisted of a bolt, door fixture or attachment, and key. When the key was inserted, pins within the fixture were lifted out of drilled holes within the bolt, allowing it to move. When the key was removed, the pins fell part-way into the bolt, preventing movement. The warded lock was also present from antiquity and remains the most recognizable lock and key design in the Western world. The first all-metal locks appeared between the years 870 and 900, and are attributed to English craftsmen. It is also said that the key was invented by Theodorus of Samos in the 6th century BC. Affluent Romans often kept their valuables in secure locked boxes within their households, and wore the keys as rings on their fingers. The practice had two benefits: It kept the key handy at all times, while signaling that the wearer was wealthy and important enough to have money and jewellery worth securing. A special type of lock, dating back to the 17th–18th century, although potentially older as similar locks date back to the 14th century, can be found in the Beguinage of the Belgian city Lier. These locks are most likely Gothic locks, that were decorated with foliage, often in a V-shape surrounding the keyhole. They are often called ''drunk man's lock'', as these locks were, according to certain sources, designed in such a way a person can still find the keyhole in the dark, although this might not be the case as the ornaments might have been purely aesthetic. Modern locks Gompa, Spiti. India. 2004 , early 20th century|alt= With the onset of the Industrial Revolution in the late 18th century and the concomitant development of precision engineering and component standardization, locks and keys were manufactured with increasing complexity and sophistication. The lever tumbler lock, which uses a set of levers to prevent the bolt from moving in the lock, was invented by Robert Barron in 1778. His double acting lever lock required the lever to be lifted to a certain height by having a slot cut in the lever, so lifting the lever too far was as bad as not lifting the lever far enough. This type of lock is still used today. The lever tumbler lock was greatly improved by Jeremiah Chubb in 1818. In 1820, Jeremiah joined his brother Charles in starting their own lock company, Chubb. Chubb made various improvements to his lock: his 1824 improved design did not require a special regulator key to reset the lock; by 1847 his keys used six levers rather than four; and he later introduced a disc that allowed the key to pass but narrowed the field of view, hiding the levers from anybody attempting to pick the lock. The Chubb brothers also received a patent for the first burglar-resisting safe and began production in 1835. The designs of Barron and Chubb were based on the use of movable levers, but Joseph Bramah, a prolific inventor, developed an alternative method in 1784. His lock used a cylindrical key with precise notches along the surface; these moved the metal slides that impeded the turning of the bolt into an exact alignment, allowing the lock to open. The lock was at the limits of the precision manufacturing capabilities of the time and was said by its inventor to be unpickable. In the same year Bramah started the Bramah Locks company at 124 Piccadilly, and displayed the "Challenge Lock" in the window of his shop from 1790, challenging "...the artist who can make an instrument that will pick or open this lock" for the reward of £200. The challenge stood for over 67 years until, at the Great Exhibition of 1851, the American locksmith Alfred Charles Hobbs was able to open the lock and, following some argument about the circumstances under which he had opened it, was awarded the prize. Hobbs' attempt required some 51 hours, spread over 16 days. The earliest patent for a double-acting pin tumbler lock was granted to American physician Abraham O. Stansbury in England in 1805, but the modern version, still in use today, was invented by American Linus Yale Sr. in 1848. This lock design used pins of varying lengths to prevent the lock from opening without the correct key. In 1861, Linus Yale Jr. was inspired by the original 1840s pin-tumbler lock designed by his father, thus inventing and patenting a smaller flat key with serrated edges as well as pins of varying lengths within the lock itself, the same design of the pin-tumbler lock which still remains in use today. The modern Yale lock is essentially a more developed version of the Egyptian lock. Despite some improvement in key design since, the majority of locks today are still variants of the designs invented by Bramah, Chubb and Yale. == Types of lock ==

• Bicycle lock • Cam lock • Chamber lock • Child safety lock • Chubb detector lock • Combination lock • Cylinder lock • Dead bolt • Disc tumbler lock • Electric strike • Electromagnetic lock • Electronic lock • Lever tumbler lock • Luggage lock • Magnetic keyed lock • Mortise lock • Padlock • Pin tumbler lock • Police lock • Protector lock • Rim lock • Time lock • Warded lock With physical keys Pin tumbler no key.svg|Pin tumbler lock: without a key in the lock, the driver pins (blue) are pushed downwards, preventing the plug (yellow) from rotating. Disc tumbler locked.png|Wafer tumbler lock: without a key in the lock, the wafers (red) are pushed down by springs. The wafers nestle into a groove in the lower part of the outer cylinder (green) preventing the plug (yellow) from rotating. Tubular locked.png|Tubular lock: the key pins (red) and driver pins (blue) are pushed towards the front of the lock, preventing the plug (yellow) from rotating. The tubular key has several half-cylinder indentations which align with the pins. A warded lock uses a set of obstructions, or wards, to prevent the lock from opening unless the correct key is inserted. The key has notches or slots that correspond to the obstructions in the lock, allowing it to rotate freely inside the lock. Warded locks are typically reserved for low-security applications as a well-designed skeleton key can successfully open a wide variety of warded locks. The pin tumbler lock uses a set of pins to prevent the lock from opening unless the correct key is inserted. The key has a series of grooves on either side of the key's blade that limit the type of lock the key can slide into. As the key slides into the lock, the horizontal grooves on the blade align with the wards in the keyway allowing or denying entry to the cylinder. A series of pointed teeth and notches on the blade, called bittings, then allow pins to move up and down until they are in line with the shear line of the inner and outer cylinder, allowing the cylinder or cam to rotate freely and the lock to open. An additional pin called the master pin is present between the key and driver pins in locks that accept master keys, to allow the plug to rotate at multiple pin elevations. A wafer tumbler lock is similar to the pin tumbler lock and works on a similar principle. However, unlike the pin lock (where each pin consists of two or more pieces) each wafer is a single piece. The wafer tumbler lock is often incorrectly referred to as a disc tumbler lock, which uses an entirely different mechanism. The wafer lock is relatively inexpensive to produce and is often used in automobiles and cabinetry. The disc tumbler lock or Abloy lock is composed of slotted rotating detainer discs. The lever tumbler lock uses a set of levers to prevent the bolt from moving in the lock. In its simplest form, lifting the tumbler above a certain height will allow the bolt to slide past. Lever locks are commonly recessed inside wooden doors or on some older forms of padlocks, including fire brigade padlocks. A magnetic keyed lock is a locking mechanism whereby the key utilizes magnets as part of the locking and unlocking mechanism. A magnetic key would use from one to many small magnets oriented so that the North and South poles would equate to a combination to push or pull the lock's internal tumblers thus releasing the lock. With electronic keys An electronic lock works by means of an electric current and is usually connected to an access control system. In addition to the pin and tumbler used in standard locks, electronic locks connect the bolt or cylinder to a motor within the door using a part called an actuator. Types of electronic locks include the following: A keycard lock operates with a flat card of similar dimensions as a credit card. In order to open the door, one needs to successfully match the signature within the keycard. The lock in a typical remote keyless system operates with a smart key radio transmitter. The lock typically accepts a particular valid code only once, and the smart key transmits a different rolling code every time the button is pressed. Generally the car door can be opened with either a valid code by radio transmission, or with a (non-electronic) pin tumbler key. The ignition switch may require a transponder car key to both open a pin tumbler lock and also transmit a valid code by radio transmission. A smart lock is an electromechanics lock that gets instructions to lock and unlock the door from an authorized device using a cryptographic key and wireless protocol. Smart locks have begun to be used more commonly in residential areas, often controlled with smartphones. Smart locks are used in coworking spaces and offices to enable keyless office entry. In addition, electronic locks cannot be picked with conventional tools. == Locksmithing ==

Locksmithing is a traditional trade, and in most countries requires completion of an apprenticeship. The level of formal education required varies from country to country, from no qualifications required at all in the UK, to a simple training certificate awarded by an employer, to a full diploma from an engineering college. Locksmiths may be commercial (working out of a storefront), mobile (working out of a vehicle), institutional, or investigational (forensic locksmiths). They may specialize in one aspect of the skill, such as an automotive lock specialist, a master key system specialist or a safe technician. Many also act as security consultants, but not all security consultants have the skills and knowledge of a locksmith. Historically, locksmiths constructed or repaired an entire lock, including its constituent parts. The rise of cheap mass production has made this less common; the vast majority of locks are repaired through like-for-like replacements, high-security safes and strongboxes being the most common exception. Many locksmiths also work on any existing door hardware, including door closers, hinges, electric strikes, and frame repairs, or service electronic locks by making keys for transponder-equipped vehicles and implementing access control systems. Although the fitting and replacement of keys remains an important part of locksmithing, modern locksmiths are primarily involved in the installation of high quality lock-sets and the design, implementation, and management of keying and key control systems. Locksmiths are frequently required to determine the level of risk to an individual or institution and then recommend and implement appropriate combinations of equipment and policies to create a "security layer" that exceeds the reasonable gain of an intruder. Key duplication Traditional key cutting is the primary method of key duplication. It is a subtractive process named after the metalworking process of cutting, where a flat blank key is ground down to form the same shape as the template (original) key. The process roughly follows these stages: • The original key is fitted into a vise in a machine, with a blank attached to a parallel vise which is mechanically linked. • The original key is moved along a guide in a movement which follows the key's shape, while the blank is moved in the same pattern against a cutting wheel by the mechanical linkage between the vices. • After cutting, the new key is deburred by scrubbing it with a metal brush to remove particles of metal which could be dangerously sharp and foul locks. Modern key cutting replaces the mechanical key following aspect with a process in which the original key is scanned electronically, processed by software, stored, then used to guide a cutting wheel when a key is produced. The capability to store electronic copies of the key's shape allows for key shapes to be stored for key cutting by any party that has access to the key image. Different key cutting machines are more or less automated, using different milling or grinding equipment, and follow the design of early 20th century key duplicators. Key duplication is available in many retail hardware stores and as a service of the specialized locksmith, though the correct key blank may not be available. More recently, online services for duplicating keys have become available. ==Keyhole==

A keyhole (or keyway) is a hole or aperture (as in a door or lock) for receiving a key. Lock keyway shapes vary widely with lock manufacturer, and many manufacturers have a number of unique profiles requiring a specifically milled key blank to engage the lock's tumblers. == Symbolism ==

Heraldry Keys appear in various symbols and coats of arms, the best-known being that of the Holy See: derived from the phrase in Matthew 16:19 which promises Saint Peter, in Roman Catholic tradition the first pope, the Keys of Heaven. But this is by no means the only case. File:Coat of arms Holy See.svg|Coat of arms of the Holy See File:Siuntio.vaakuna.svg|A key pictured in the coat of arms of Siuntio Artwork Some works of art associate keys with the Greek goddess of witchcraft, known as Hecate. Palestinian key demonstration in Berlin The Palestinian key is the Palestinian collective symbol of their homes lost in the Nakba, when more than half of the population of Mandatory Palestine was expelled or fled violence in 1948 and were subsequently refused the right to return. Since 2016, a Palestinian restaurant in Doha, Qatar, holds the Guinness World Record for the world's largest key – 2.7 tonnes and 7.8 × 3 meters. == See also ==