MC4 connector

MC4 connectors were introduced by Multi-Contact in 2004 as successors to Multi-Contact's MC3 connector (with a 3 mm diameter contact pin) developed in 1996. MC3 had certification ratings of (1000VIEC/600V UL) and 30A (using 10AWG PV Cable). MC3 connectors were discontinued in 2016. While small solar panels used for battery charging and similar tasks may not require special connectors, larger systems normally connect the panels together in series to form strings. In the past, this was accomplished by opening a small electrical box on the back of the panel and connecting user-supplied wires to screw terminals within. However, in the United States, bare terminals of this sort are limited to 50V or less by the National Electrical Code (NEC). Additionally, these sorts of connections were subject to problems caused by water leakage, electrical corrosion and mechanical stress on the wires. Starting in the 2000s, a number of companies introduced products to address these issues. In these systems, the junction box was sealed and two wires were permanently attached using strain reliefs. The cables ended with PV connectors that met the definition of a convenience receptacle, meaning they could be (legally) connected together by anyone. Two connectors became somewhat common during this period, the Radox connector and MC3 connector, both of which essentially looked like weather-sealed phono jacks. In 2008, the NEC banned connectors that allowed disconnection under load, which was seen in the field when snow or debris piled up on the cables. PV connectors were now required to contain positive locking mechanisms controlled by certified, product specific tools. Radox, a European manufacturer, did not respond to this specification and has since disappeared from the market. Tyco Electronics and Multi-Contact (purchased by Stäubli in 2002), responded by introducing new connectors to meet this requirement. The MC4 PV connector, launched in 2004, provided these positive locking mechanisms, leading to widespread market acceptance. Tyco's Solarlok became a market leader for a period in the late 2000s, but a number of factors conspired to push it from the market. Among these was that the system had two sets of cables and wires, which led to considerable annoyance in the field when equipment from different vendors could not be plugged together. By 2011, the MC4 was already in a strong leadership position, which led to the introduction of products from a variety of other connector vendors. As of 2022, Staubli Electrical Connectors possesses 50% of its global market shares. The MC4 EVO2 is a backward-compatible version of the MC4 connector with higher ratings. ==Description==

The MC4 system consists of a plug and socket design. The metal contacts of the plugs and sockets are inside plastic insulators; the plug's metal contact is inside a cylindrical insulator that looks like a socket, and the socket metal contact is inside a square probe that appears as a plug. The socket has two plastic locking tabs that have to be pressed toward the central probe slightly to insert into holes in the front of the plug connector. When the two are pushed together, the fingers slide down the holes until they reach a notch in the side of the plug connector, where they pop outward to lock the two together. For a proper seal, MC4s must be used with cable of the correct diameter. The cable is normally double-insulated (insulation plus black sheath) and both UV and higher temperature resistant (most cables deteriorate if used outdoors without protection from sunlight). Connectors are typically attached by crimping, though soldering is also possible. The MC4 connector is UL rated at 1500V DC and up to 95A with the 6AWG PV Cable. MC4-Evo 2 has both UL and IEC certification ratings of 1500V DC and up to 70A with 10 mm² PV Cable, depending on the conductor size used in pairs. ==Application and safety==

Stäubli's (formerly Multi-Contact) MULTILAM Technology claims that constant spring pressure provides reliable low contact resistance. However, it is very important never to connect or disconnect them under load, even on low-voltage (12–48V) systems. An electric arc may form which can melt and seriously damage contact materials, resulting in high resistance and subsequent overheating. This is partly because direct current (DC) continues to arc, whereas commonly used alternating current (AC) more readily self-extinguishes at the zero-crossing voltage point. Large arrays of panels are commonly interconnected in series, made of strings of panels generating 17V to 50V each, with overall voltages up to 600V per string or 1500V in special large arrays with high voltage panels. The installation manuals from Stäubli on MC4 connectors instruct to avoid using non-Stäubli connectors. Product certifications and the manufacturer's warranty only would apply if MC4 connectors are mated to connectors from the same type made by Stäubli Electrical Connectors. ==See also==