Mechanical floor

. The truss sections (made of triangular struts) will house mechanical floors. Some skyscrapers have narrow building cores that require stabilization to prevent collapse. Typically, this is accomplished by joining the core to the external supercolumns at regular intervals using outrigger trusses. The triangular shape of the struts precludes the laying of tenant floors, so these sections house mechanical floors instead, typically in groups of two. Additional stabilizer elements such as tuned mass dampers also require mechanical floors to contain or service them. This layout is usually reflected in the internal elevator zoning. Since nearly all elevators require machine rooms above the last floor they service, mechanical floors are often used to divide shafts that are stacked on top of each other to save space. A transfer level or skylobby is sometimes placed just below those floors. Elevators that reach the top tenant floor also require overhead machine rooms; those are sometimes put into full-size mechanical floors but most often into a mechanical penthouse, which can also contain communications gear and window-washing equipment. On most building designs, this is a simple "box" on the roof, while on others it is concealed inside a decorative spire. A consequence of this is that if the topmost mechanical floors are counted in the total, there can be no such thing as a true "top-floor office" in a skyscraper with this design. ==Mechanical concerns==

of the World Trade Center, c. September-October 2000. The Twin Towers required multiple mechanical floors at all levels of the skyscrapers for HVAC and elevator systems. Besides structural support and elevator management, the primary purpose of mechanical floors is services to house heating, ventilation, and air conditioning (HVAC) equipment. They may contain air handling units, cooling towers (in mechanical penthouses), electrical generators, chiller plants, and water pumps. In particular, the problem of bringing and keeping water on the upper floors is an important constraint in the design of skyscrapers. Water is necessary for tenant use, air conditioning, equipment cooling, and basic firefighting through sprinklers (especially important since ground-based firefighting equipment usually cannot reach higher than a dozen floors or so). It is inefficient, and seldom feasible, for water pumps to send water directly to a height of several hundred meters, so intermediate pumps and water tanks are used. The pumps on each group of mechanical floors act as a relay to the next one up, while the tanks hold water in reserve for normal and emergency use. Usually the pumps have enough power to bypass a level if the pumps there have failed, and send water two levels up. Special care is taken towards fire safety on mechanical floors that contain generators, compressors, and elevator machine rooms, since oil is used as either a fuel or lubricant in those elements. Mechanical floors also contain communication and control systems that service the building and sometimes outbound communications, such as through a large rooftop antenna (which is also physically held in place inside the top-floor mechanical levels). Modern computerized HVAC control systems minimize the problem of equipment distribution among floors by enabling central remote control. ==Aesthetics concerns==

twin towers. The "dark bands" were vents for the mechanical floors. Most mechanical floors require external vents or louvers for ventilation and heat rejection along most or all of their perimeter, precluding the use of glass windows. The resulting visible "dark bands" can disrupt the overall facade design, especially if it is fully glass-clad. Different architectural styles approach this challenge in different ways. In the Modern and International styles of the 1960s and 1970s where form follows function, the vents' presence is not seen as undesirable. Rather it emphasizes the functional layout of the building by dividing it neatly into equal blocks, mirroring the layout of the elevators and offices inside. This could be clearly seen on the Twin Towers of the World Trade Center and can be seen on the Willis Tower. In the IDS Tower in Minneapolis, the lowest mechanical floor serves as a visual separation from the street- and skyway-level Crystal Court shopping center and the office tower above; the upper mechanical floor (above the 50th and 51st floors, the uppermost occupied floors) serves as a "crown" to the building. Conversely, designers of the recent postmodern-style skyscrapers strive to mask the vents and other mechanical elements in various ways. This is accomplished through such means as complex wall angles (Petronas Towers), intricate latticework cladding (Jin Mao Building), or non-glassed sections that appear to be ornamental (Taipei 101, roof of Jin Mao Building). Some low-rise, residential (usually apartment buildings or dormitories), or non-residential buildings, especially built in an architecture style that promotes the use of elements such as sloped roofs and/or bell towers, may have mechanical floors disguised as attics or towers. In this case, the ventilation systems of the mechanical floor are seen as gable vents, dormers, or abat-sons (louvers in a bell tower). Examples include some buildings in UCLA, like Dodd Hall, which has a mechanical floor disguised as an attic and a bell tower. ==Examples==

These are examples of above-ground mechanical floor layouts for some of the world's tallest buildings. In each case, mechanical penthouses and spires are counted as floors, leading to higher total floor counts than usual. • Taipei 101: Floors 7–8, 17–18, 25–26, 34, 42, 50, 58, 66, 74, 82, 87, 90, 92 to 100 in the penthouse – total 17/102, 17%. The official count of 11 corresponds to the number of groups in the office section. Floors 92–100 contain communications equipment and so are not typically counted as mechanical since they do not service the building itself. • One World Trade Center: Floors 2–19, 92–99, and 103–104 – total 28/104, 26%. • Previous WTC (Twin Towers): Floors 7–8, 41–42, 75–76, and 108–109 – total 8/110, 7%. The 110th Floor of 1 WTC (North Tower) housed television and radio transmission equipment. Some sources erroneously mention 12 floors, in groups of three, due to the height of the vents (actually the ceilings there were higher) and because levels 44 and 78 were skylobbies which in many buildings sit directly on top of the mechanical floors. However, the twin towers had one occupied office floor under each skylobby, accessible through escalators. • Willis Tower (Formerly Sears Tower): Levels 29–32, 64–65, 88–89, 104–108, 109 (penthouse), and 110 (penthouse roof) – total 15/110, 13%. • Petronas Towers: Floors 6–7, 38–40, 43, 84, 87–88 – total 9/88, 10% • Jin Mao Building: Floors 51–52, and 89–93 in the penthouse – total 7/93, 7.5% • Burj Khalifa: Floors 17–18, 40–42, 73–75, 109–111, 136–138, 155, and 160–168, in the penthouse – total 25/168, 15% • John Hancock Center: Floors 16–17, 42–43, 93, 99–100 (penthouse) – total 7/100, 7% • Empire State Building: Floors 87–101 – total 15/102, 14% • Shanghai Tower: Floors 6–7, 20–21, 35–36, 50–51, 66–67, 82–83, 99–100, 116–117, 122–124, and 128 – total 20/128, 16% • Shanghai World Financial Center: Floors 6, 18, 30, 42, 54, 66, 78, 89, and 90 – total 9/101, 9% • Lotte World Tower: Floors 3–4, 13, 21–23, 39–41, 59, 60, 72–75, 83, 84, 102–106, 115, and 116 – total 24/123, 20% == References ==