Magnetohydrodynamic generator

In a conventional thermal power plant, like a coal-fired power station or nuclear power plant, the energy created by the chemical or nuclear reactions is absorbed in a working fluid, usually water. In a coal plant, for instance, the coal burns in an open chamber which is surrounded by tubes carrying water. The heat from the combustion is absorbed by the water which boils into steam. The steam is then sent into a steam turbine which extracts energy from the steam by turning it into rotational motion. The steam is slowed and cooled as it passes through the turbine. The rotational motion then turns an electrical generator. The efficiency of this overall cycle, known as the Rankine cycle, is a function of the temperature difference between the inlet to the boiler and the outlet to the turbine. The maximum temperature at the turbine is a function of the energy source; and the minimum temperature at the inlet is a function of the surrounding environment's ability to absorb waste heat. For many practical reasons, coal plants generally extract about 35% of the heat energy from the coal, the rest is ultimately dumped into the cooling system or escapes through other losses. MHD generators can extract more energy from the fuel source than turbine-generator systems. They do this by skipping the step where the heat is transferred to another working fluid. Instead, they use the hot exhaust directly as the working fluid. In the case of a coal plant, the exhaust is directed through a nozzle that increases its velocity, essentially a rocket nozzle, and then directs it through a magnetic system that directly generates electricity. In a conventional generator, rotating magnets move past a material filled with nearly-free electrons, typically copper wire (or vice versa depending on the design). In the MHD system the electrons in the exhaust gas move past a stationary magnet. Ultimately the effect is the same, the working fluid is slowed down and cools as its kinetic energy is transferred to electrons, and is thereby converted to electrical power. MHD can only be used with power sources that produce large amounts of fast moving plasma, like the gas from burning coal. This means it is not suitable for systems that work at lower temperatures or do not produce an ionized gas, like a solar power tower or nuclear reactor. In the early days of development of nuclear power, one alternative design was the gaseous fission reactor, which did produce plasma, and this led to some interest in MHD for this role. This style of reactor was never built, however, and interest from the nuclear industry waned. The vast majority of work on MHD for electrical generation has been related to coal-fired plants. ==Principle==

The Lorentz Force Law describes the effects of a charged particle moving in a constant magnetic field. The simplest form of this law is given by the vector equation. \mathbf{F} = Q \left(\mathbf{v}\times\mathbf{B}\right) where • is the force acting on the particle. • is the charge of the particle, • is the velocity of the particle, and • is the magnetic field. The vector is perpendicular to both and according to the right hand rule. == Power generation ==

Typically, for a large power station to approach the operational efficiency of computer models, steps must be taken to increase the electrical conductivity of the conductive substance. Heating a gas to its plasma state, or adding other easily ionizable substances like the salts of alkali metals, can help to accomplish this. In practice, a number of issues must be considered in the implementation of an MHD generator: generator efficiency, economics, and toxic byproducts. These issues are affected by the choice of one of the three MHD generator designs: the Faraday generator, the Hall generator, and the disc generator. Faraday generator The Faraday generator is named for Michael Faraday's experiments on moving charged particles in the Thames River. A simple Faraday generator consists of a wedge-shaped pipe or tube of some non-conductive material. When an electrically conductive fluid flows through the tube, in the presence of a significant perpendicular magnetic field, a voltage is induced in the fluid. This can be drawn off as electrical power by placing electrodes on the sides, at 90-degree angles to the magnetic field. There are limitations on the density and type of field used in this example. The amount of power that can be extracted is proportional to the cross-sectional area of the tube and the speed of the conductive flow. The conductive substance is also cooled and slowed by this process. MHD generators typically reduce the temperature of the conductive substance from plasma temperatures to just over 1000 °C. The main practical problem of a Faraday generator is that differential voltages and currents in the fluid may short through the electrodes on the sides of the duct. The generator can also experience losses from the Hall effect current, which makes the Faraday duct inefficient. Most further refinements of MHD generators have tried to solve this problem. The optimal magnetic field on duct-shaped MHD generators is a sort of saddle shape. To get this field, a large generator requires an extremely powerful magnet. Many research groups have tried to adapt superconducting magnets to this purpose, with varying success. Hall generator The typical solution has been to use the Hall effect to create a current that flows with the fluid. This design has arrays of short, segmented electrodes on the sides of the duct. The first and last electrodes in the duct power the load. Each other electrode is shorted to an electrode on the opposite side of the duct. These shorts of the Faraday current induce a powerful magnetic field within the fluid, but in a chord of a circle at right angles to the Faraday current. This secondary, induced field makes the current flow in a rainbow shape between the first and last electrodes. Losses are less than in a Faraday generator, and voltages are higher because there is less shorting of the final induced current. However, this design has problems because the speed of the material flow requires the middle electrodes to be offset to "catch" the Faraday currents. As the load varies, the fluid flow speed varies, misaligning the Faraday current with its intended electrodes, and making the generator's efficiency very sensitive to its load. Disc generator The third and, currently, the most efficient design is the Hall effect disc generator. This design currently holds the efficiency and energy density records for MHD generation. A disc generator has fluid flowing between the center of a disc, and a duct wrapped around the edge. (The ducts are not shown.) The magnetic excitation field is made by a pair of circular Helmholtz coils above and below the disk. (The coils are not shown.) The Faraday currents flow in a perfect dead short around the periphery of the disk. The Hall effect currents flow between ring electrodes near the center duct and ring electrodes near the periphery duct. The wide flat gas flow reduced the distance, hence the resistance of the moving fluid. This increases efficiency. Another significant advantage of this design is that the magnets are more efficient. First, they cause simple parallel field lines. Second, because the fluid is processed in a disk, the magnet can be closer to the fluid, and in this geometry, magnetic field strengths increase as the 7th power of distance. Finally, the generator is compact, so the magnet is smaller and uses a much smaller percentage of the generated power. Generator efficiency The efficiency of the direct energy conversion in MHD power generation increases with the magnetic field strength and the plasma conductivity, which depends directly on the plasma temperature, and more precisely on the electron temperature. As very hot plasmas can only be used in pulsed MHD generators (for example using shock tubes) due to the fast thermal material erosion, it was envisaged to use nonthermal plasmas as working fluids in steady MHD generators, where only free electrons are heated a lot (10,000–20,000 kelvins) while the main gas (neutral atoms and ions) remains at a much lower temperature, typically 2500 kelvins. The goal was to preserve the materials of the generator (walls and electrodes) while improving the limited conductivity of such poor conductors to the same level as a plasma in thermodynamic equilibrium; i.e. completely heated to more than 10,000 kelvins, a temperature that no material could stand. Evgeny Velikhov first discovered theoretically in 1962 and experimentally in 1963 that an ionization instability, later called the Velikhov instability or electrothermal instability, quickly arises in any MHD converter using magnetized nonthermal plasmas with hot electrons, when a critical Hall parameter is reached, depending on the degree of ionization and the magnetic field. This instability greatly degrades the performance of nonequilibrium MHD generators. The prospects of this technology, which initially predicted high efficiencies, crippled MHD programs all over the world as no solution to mitigate the instability was found at that time. Without implementing solutions to overcome the electrothermal instability, practical MHD generators had to limit the Hall parameter or use moderately-heated thermal plasmas instead of cold plasmas with hot electrons, which severely lowers efficiency. As of 1994, the 22% efficiency record for closed-cycle disc MHD generators was held by Tokyo Technical Institute. The peak enthalpy extraction in these experiments reached 30.2%. Typical open-cycle Hall & duct coal MHD generators are lower, near 17%. These efficiencies make MHD unattractive, by itself, for utility power generation, since conventional Rankine cycle power plants can reach 40%. However, the exhaust of an MHD generator burning fossil fuel is almost as hot as a flame. By routing its exhaust gases into a heat exchanger for a turbine Brayton cycle or steam generator Rankine cycle, MHD can convert fossil fuels into electricity with an overall estimated efficiency of up to 60 percent, compared to the 40 percent of a typical coal plant. A magnetohydrodynamic generator might also be the first stage of a gas core reactor. Material and design issues MHD generators have problems in regard to materials, both for the walls and the electrodes. Materials must not melt or corrode at very high temperatures. Exotic ceramics were developed for this purpose, selected to be compatible with the fuel and ionization seed. The exotic materials and the difficult fabrication methods contribute to the high cost of MHD generators. MHDs also work better with stronger magnetic fields. The most successful magnets have been superconducting, and very close to the channel. A major difficulty was refrigerating these magnets while insulating them from the channel. The problem is worse because the magnets work better when they are closer to the channel. There are also risks of damage to the hot, brittle ceramics from differential thermal cracking: magnets are usually near absolute zero, while the channel is several thousand degrees. For MHDs, both alumina (Al2O3) and magnesium peroxide (MgO2) were reported to work for the insulating walls. Magnesium peroxide degrades near moisture. Alumina is water-resistant and can be fabricated to be quite strong, so in practice, most MHDs have used alumina for the insulating walls. For the electrodes of clean MHDs (i.e. burning natural gas), one good material was a mix of 80% CeO2, 18% ZrO2, and 2% Ta2O5. Coal-burning MHDs have highly corrosive environments with slag. The slag both protects and corrodes MHD materials. In particular, migration of oxygen through the slag accelerates the corrosion of metallic anodes. Nonetheless, very good results have been reported with stainless steel electrodes at 900K. Another, perhaps superior option is a spinel ceramic, FeAl2O4 - Fe3O4. The spinel was reported to have electronic conductivity, absence of a resistive reaction layer but with some diffusion of iron into the alumina. The diffusion of iron could be controlled with a thin layer of very dense alumina, and water cooling in both the electrodes and alumina insulators. Attaching the high-temperature electrodes to conventional copper bus bars is also challenging. The usual methods establish a chemical passivation layer, and cool the busbar with water. showed that a large coal-fired MHD combined cycle plant could attain a HHV energy efficiency approaching 60 percent—well in excess of other coal-fueled technologies, so the potential for low operating costs exists. However, no testing at those aggressive conditions or size has yet occurred, and there are no large MHD generators now under test. There is simply an inadequate reliability track record to provide confidence in a commercial coal-fuelled MHD design. U25B MHD testing in Russia using natural gas as fuel used a superconducting magnet, and had an output of 1.4 megawatts. A coal-fired MHD generator series of tests funded by the U.S. Department of Energy (DOE) in 1992 produced MHD power from a larger superconducting magnet at the Component Development and Integration Facility (CDIF) in Butte, Montana. None of these tests were conducted for long-enough durations to verify the commercial durability of the technology. Neither of the test facilities were in large-enough scale for a commercial unit. Superconducting magnets are used in the larger MHD generators to eliminate one of the large parasitic losses: the power needed to energize the electromagnet. Superconducting magnets, once charged, consume no power and can develop intense magnetic fields 4 teslas and higher. The only parasitic load for the magnets are to maintain refrigeration, and to make up the small losses for the non-supercritical connections. Because of the high temperatures, the non-conducting walls of the channel must be constructed from an exceedingly heat-resistant substance such as yttrium oxide or zirconium dioxide to retard oxidation. Similarly, the electrodes must be both conductive and heat-resistant at high temperatures. The AVCO coal-fueled MHD generator at the CDIF was tested with water-cooled copper electrodes capped with platinum, tungsten, stainless steel, and electrically conducting ceramics. Toxic byproducts MHD reduces the overall production of fossil fuel wastes because it increases plant efficiency. In MHD coal plants, the patented commercial "Econoseed" process developed by the U.S. (see below) recycles potassium ionization seed from the fly ash captured by the stack-gas scrubber. However, this equipment is an additional expense. If molten metal is the armature fluid of an MHD generator, care must be taken with the coolant of the electromagnetics and channel. The alkali metals commonly used as MHD fluids react violently with water. Also, the chemical byproducts of heated, electrified alkali metals and channel ceramics may be poisonous and environmentally persistent. == History ==

The first practical MHD power research was funded in 1938 in the U.S. by Westinghouse in its Pittsburgh, Pennsylvania laboratories, headed by Hungarian Bela Karlovitz. The initial patent on MHD is by B. Karlovitz, U.S. Patent No. 2,210,918, "Process for the Conversion of Energy", August 13, 1940. World War II interrupted development. In 1962, the First International Conference on MHD Power was held in Newcastle upon Tyne, UK by Dr. Brian C. Lindley of the International Research and Development Company Ltd. The group set up a steering committee to set up further conferences and disseminate ideas. In 1964, the group held a second conference in Paris, France, in consultation with the European Nuclear Energy Agency. Since membership in the ENEA was limited, the group persuaded the International Atomic Energy Agency to sponsor a third conference, in Salzburg, Austria, July 1966. Negotiations at this meeting converted the steering committee into a periodic reporting group, the ILG-MHD (international liaison group, MHD), under the ENEA, and later in 1967, also under the International Atomic Energy Agency. Further research in the 1960s by R. Rosa established the practicality of MHD for fossil-fueled systems. In the 1960s, AVCO Everett Aeronautical Research began a series of experiments, ending with the Mk. V generator of 1965. This generated 35MW, but used about 8 MW to drive its magnet. In 1966, the ILG-MHD had its first formal meeting in Paris, France. It began issuing a periodic status report in 1967. This pattern persisted, in this institutional form, up until 1976. Toward the end of the 1960s, interest in MHD declined because nuclear power was becoming more widely available. In the late 1970s, as interest in nuclear power declined, interest in MHD increased. In 1975, UNESCO became persuaded that MHD might be an efficient way to utilise world coal reserves, and in 1976, sponsored the ILG-MHD. In 1976, it became clear that no nuclear reactor in the next 25 years would use MHD, so the International Atomic Energy Agency and ENEA (both nuclear agencies) withdrew support from the ILG-MHD, leaving UNESCO as the primary sponsor of the ILG-MHD. Former Yugoslavia development Engineers in former Yugoslavian Institute of Thermal and Nuclear Technology (ITEN), Energoinvest Co., Sarajevo, built and patented the first experimental Magneto-Hydrodynamic facility power generator in 1989. U.S. development In the 1980s, the U.S. Department of Energy began a multiyear program, culminating in a 1992 50 MW demonstration coal combustor at the Component Development and Integration Facility (CDIF) in Butte, Montana. This program also had significant work at the Coal-Fired-In-Flow-Facility (CFIFF) at University of Tennessee Space Institute. This program combined four parts: • An integrated MHD topping cycle, with channel, electrodes, and current control units developed by AVCO, later known as Textron Defence of Boston. This system was a Hall effect duct generator heated by pulverized coal, with a potassium ionisation seed. AVCO had developed the famous Mk. V generator, and had significant experience. • An integrated bottoming cycle, developed at the CDIF. • A facility to regenerate the ionization seed was developed by TRW. Potassium carbonate is separated from the sulphate in the fly ash from the scrubbers. The carbonate is removed, to regain the potassium. • A method to integrate MHD into preexisting coal plants. The Department of Energy commissioned two studies. Westinghouse Electric performed a study based on the Scholtz Plant of Gulf Power in Sneads, Florida. The MHD Development Corporation also produced a study based on the J.E. Corrette Plant of the Montana Power Company of Billings, Montana. Initial prototypes at the CDIF operated for short durations, with various coals: Montana Rosebud, and a high-sulphur corrosive coal, Illinois No. 6. A great deal of engineering, chemistry, and material science was completed. After the final components were developed, operational testing completed with 4,000 hours of continuous operation, 2,000 on Montana Rosebud, 2,000 on Illinois No. 6. The testing ended in 1993. Japanese development The Japanese program in the late 1980s concentrated on closed-cycle MHD. The belief was that it would have higher efficiencies, and smaller equipment, especially in the clean, small, economical plant capacities near 100 megawatts (electrical) which are suited to Japanese conditions. Open-cycle coal-powered plants are generally thought to become economic above 200 megawatts. The first major series of experiments was FUJI-1, a blow-down system powered from a shock tube at the Tokyo Institute of Technology. These experiments extracted up to 30.2% of enthalpy, and achieved power densities near 100 megawatts per cubic meter. This facility was funded by Tokyo Electric Power, other Japanese utilities, and the Department of Education. Some authorities believe this system was a disc generator with a helium and argon carrier gas and potassium ionization seed. In 1994, there were detailed plans for FUJI-2, a 5 MWe continuous closed-cycle facility, powered by natural gas, to be built using the experience of FUJI-1. The basic MHD design was to be a system with inert gases using a disk generator. The aim was an enthalpy extraction of 30% and an MHD thermal efficiency of 60%. FUJI-2 was to be followed by a retrofit to a 300MWe natural gas plant. Australian development From the 1980s, Professor Hugo Messerle at The University of Sydney researched coal-fueled MHD. This resulted in a 28MWe topping facility that was operated outside Sydney. Messerle also wrote a key reference work on MHD, as part of a UNESCO education program. Italian development The Italian program began in 1989 with a budget of about 20 million $US, and had three main development areas: • MHD Modelling. • Superconducting magnet development. The goal in 1994 was a prototype 2m long, storing 66MJ, for an MHD demonstration 8m long. The field was to be 5teslas, with a taper of 0.15T/m. The geometry was to resemble a saddle shape, with cylindrical and rectangular windings of niobium-titanium copper. • Retrofits to natural gas powerplants. One was to be at the Enichem-Anic factor in Ravenna. In this plant, the combustion gases from the MHD would pass to the boiler. The other was a 230MW (thermal) installation for a power station in Brindisi, that would pass steam to the main power plant. Chinese development A joint U.S.-China national programme ended in 1992 by retrofitting the coal-fired No. 3 plant in Asbach. A further eleven-year program was approved in March 1994. This established centres of research in: • The Institute of Electrical Engineering in the Chinese Academy of Sciences, Beijing, concerned with MHD generator design. • The Shanghai Power Research Institute, concerned with overall system and superconducting magnet research. • The Thermoenergy Research Engineering Institute at the Nanjing's Southeast University, concerned with later developments. The 1994 study proposed a 10W (electrical, 108MW thermal) generator with the MHD and bottoming cycle plants connected by steam piping, so either could operate independently. Russian developments In 1971, the natural-gas-fired U-25 plant was completed near Moscow, with a designed capacity of 25 megawatts. By 1974 it delivered 6 megawatts of power. By 1994, Russia had developed and operated the coal-operated facility U-25, at the High-Temperature Institute of the Russian Academy of Science in Moscow. U-25's bottoming plant was operated under contract with the Moscow utility, and fed power into Moscow's grid. There was substantial interest in Russia in developing a coal-powered disc generator. In 1986 the first industrial power plant with MHD generator was built, but in 1989 the project was cancelled before MHD launch and this power plant later joined to Ryazan Power Station as a 7th unit with ordinary construction. == See also ==