Non-Newtonian fluid

Summary Shear thickening fluid The viscosity of a shear thickeningi.e. dilatant fluid appears to increase when the shear rate increases. Corn starch suspended in water ("oobleck", see below) is a common example: when stirred slowly it looks milky, when stirred vigorously it feels like a very viscous liquid. Shear thinning fluid . Therefore, instead of slipping along the surface, it forms very large and very dense droplets with limited dripping. A familiar example of the opposite, a shear thinning fluid, or pseudoplastic fluid, is wall paint: The paint should flow readily off the brush when it is being applied to a surface but not drip excessively. Note that all thixotropic fluids are extremely shear thinning, but they are significantly time dependent, whereas the colloidal "shear thinning" fluids respond instantaneously to changes in shear rate. Thus, to avoid confusion, the latter classification is more clearly termed pseudoplastic. Another example of a shear thinning fluid is blood. This application is highly favoured within the body, as it allows the viscosity of blood to decrease with increased shear strain rate. Bingham plastic Fluids that have a linear shear stress/shear strain relationship but require a finite yield stress before they begin to flow (the plot of shear stress against shear strain does not pass through the origin) are called Bingham plastics. Several examples are clay suspensions, drilling mud, toothpaste, mayonnaise, chocolate, and mustard. The surface of a Bingham plastic can hold peaks when it is still. By contrast Newtonian fluids have flat featureless surfaces when still. Rheopectic or anti-thixotropic There are also fluids whose strain rate is a function of time. Fluids that require a gradually increasing shear stress to maintain a constant strain rate are referred to as rheopectic. An opposite case of this is a fluid that thins out with time and requires a decreasing stress to maintain a constant strain rate (thixotropic). ==Examples==

Many common substances exhibit non-Newtonian flows. These include: • Soap solutions, cosmetics, and toothpaste • Food such as butter, cheese, jam, mayonnaise, soup, and yogurt An inexpensive, non-toxic example of a non-Newtonian fluid is a suspension of starch (e.g., cornstarch/cornflour) in water, sometimes called "oobleck", "ooze", or "magic mud" (1 part of water to 1.5–2 parts of corn starch). The name "oobleck" is derived from the Dr. Seuss book Bartholomew and the Oobleck. Chilled caramel topping Another example of non-Newtonian fluid flow is chilled caramel ice cream topping (so long as it incorporates hydrocolloids such as carrageenan and gellan gum). The sudden application of force—by stabbing the surface with a finger, for example, or rapidly inverting the container holding it—causes the fluid to behave like a solid rather than a liquid. This is the "shear thickening" property of this non-Newtonian fluid. More gentle treatment, such as slowly inserting a spoon, will leave it in its liquid state. Trying to jerk the spoon back out again, however, will trigger the return of the temporary solid state. Silly Putty Silly Putty is a silicone polymer based suspension that will flow, bounce, or break, depending on strain rate. Plant resin Plant resin is a viscoelastic solid polymer. When left in a container, it will flow slowly as a liquid to conform to the contours of its container. If struck with greater force, however, it will shatter as a solid. Quicksand Quicksand is a shear thinning non-Newtonian colloid that gains viscosity at rest. Quicksand's non-Newtonian properties can be observed when it experiences a slight shock (for example, when someone walks on it or agitates it with a stick), shifting between its gel and sol phase and seemingly liquefying, causing objects on the surface of the quicksand to sink. Ketchup Ketchup is a shear thinning fluid. Shear thinning means that the fluid viscosity decreases with increasing shear stress. In other words, fluid motion is initially difficult at slow rates of deformation, but will flow more freely at high rates. Shaking an inverted bottle of ketchup can cause it to transition to a lower viscosity through shear thinning, making it easier to pour from the bottle. Dry granular flows Under certain circumstances, flows of granular materials can be modelled as a continuum, for example using the μ(I) rheology. Such continuum models tend to be non-Newtonian, since the apparent viscosity of granular flows increases with pressure and decreases with shear rate. The main difference is the shearing stress and rate of shear. ==See also==