München At the outbreak of World War Two, the British aviation industry expanded greatly. There was great need for the
Rolls-Royce Merlin engine with shadow factories being established in Crewe, Manchester, and Glasgow. This was not enough to meet increasing demand with the British government looking to expand production using U.S. manufacturers. An agreement was reached between Rolls-Royce and the
Packard Motor Car Company in September 1940 to manufacture the Merlin under license, with a $130,000,000 order being placed. The first Packard-built engine, designated
V-1650-1, ran in August 1941. The first American model was a version of the Mark XX, designated the V-1650-1 by the American military and the Packard Merlin 28 by the British. This engine used a single-stage, two-speed supercharger, the gear changing mechanism of which originally came from a French Farman patent license. The Merlin 28 was used for the
Avro Lancaster bomber. The USAAF V-1650-1 version of this engine was used in the
Curtiss P-40Fs. The initial Packard modifications to this engine changed the main
crankshaft bearings from a copper-lead alloy to a silver-lead combination and featured
indium plating. The bearing coating improved the break-in (running-in) and load-carrying abilities of the surface. In answer to a request from the British
Air Ministry for a high-altitude Merlin for the pressurised
Wellington VI high-altitude bomber, a Rolls-Royce team under the direction of
Stanley Hooker developed a Merlin with two-stage supercharging, which became the Merlin 60-series. The first 60-series engine ran in March 1941, and was first flown in July the same year. When only 63 examples of the otherwise-cancelled Wellington VI were produced, these engines were instead introduced on the
Spitfire IX as the Merlin 61. This model was later produced by Packard as the V-1650-3 and became known as the "high altitude" Merlin destined for the P-51, the first two-stage Merlin-Mustang conversion flying with a Merlin 65 as the
Mustang X in October 1942, the production V-1650-3 engined P-51B (Mustang III) entering service in 1943. The two-speed, two-stage supercharger section of the two-stage Merlins and V-1650-3 featured two separate impellers on the same shaft that were normally driven through a gear train at a ratio of 6.391:1. A hydraulic gear change arrangement of oil-operated clutches could be engaged by an electric solenoid to increase this ratio to 8.095:1 in high speed blower position. The high speed gear ratio of the impellers was not as high as the ratio used in the
Allison, but impeller speed is not the only factor that determines engine performance, which is also a function of the size and pitch of the impeller blades. The gear-driven supercharger is a parasitic accessory; therefore, impeller gearing and blade profiles are carefully designed for maximum power at altitude without compromise of available power at the critical take off stage of flight. The double staging of the compressed fuel/air mixture provided the boost pressure through a diffuser to the intake manifolds that increased the
critical altitude of the power plant. The ability of the supercharger to maintain a sea level pressure in the induction system to the cylinders allowed the Packard Merlin to develop more than above . The two-stage impeller created extreme heating of the fuel/air mixture during the compression process, and, to prevent detonation of the compressed charge, it was necessary to cool the mixture prior to entry into the cylinders. The cooling was accomplished in an
intercooler passage cast into the wheel case housing between the first and second-stage impellers and an additional cooling fin and tube core placed between the outlet of the blower and the induction manifold to the cylinders.
Ethylene glycol coolant was circulated by a pump through these to carry off the excess heat generated by the impellers. Without the intercooler the temperature increase in the charge could be as high as 205 °C (401 °F). The glycol mixture used for cooling was independent of the main engine cooling system and used a centrifugal pump driven by the engine to circulate the coolant through an aircraft radiator system at a maximum rate of 36 U.S. gallons (136 litres, 30 Imperial gallons) per minute, depending on engine rpm. This combined system reduced the charge temperature to suitable levels. Throttle valves in the updraft carburettor throat were controlled by an automatic boost control through the throttle linkage to maintain the selected manifold pressure with changes in altitude. The valves were only partially open during ground and low-level operation to prevent overboosting of the engine. As air density decreases with increased altitude, the throttle valves were progressively opened in response to the reducing atmospheric pressure. This system provided full power within engine boost limitations up to the critical altitude of .
Measurement of boost pressure The British measured boost pressure as lbf/in2 (psi). The normal atmospheric pressure at sea level is 14.7 psi, so a reading of +6 means that the air/fuel mix is being compressed by a supercharger blower to 20.7 psi before entering the engine; +25 means that the air/fuel mix is now being compressed to 39.7 psi. The Americans measured their boost ratings using
inches of mercury (inHg). One pound-force per square inch equals or , and a standard atmosphere is 101.325 kPa =29.92 inHg =14.70 lbf/in2. In early Merlin engines the maximum manifold (boost) pressure was +12 on 100 octane fuel. This was increased in later models.
Postwar use In the United States many
war surplus engines and airframes were sold relatively cheaply – two of the most popular items were
North American P-51 Mustangs and Packard V-1650 Merlin engines, several of which were "souped up" and modified for air racing in the
Bendix Trophy, the Cleveland
Air Races, and the
Thompson Trophy. Many of these engines remain heavily used to this day in
Drag Racing,
Hydroplane racing, and
Land Speed Racing at places like the
Bonneville Salt Flats. The Mynarski Lancaster flown by the Canadian Warplane Heritage Museum in Hamilton, Ontario, Canada, one of only two Lancasters flying in the world, uses four Packard Merlin engines. Work continues on increasing the power output of the Merlin for the Unlimited Class racers at the
Reno Air Races. Innovations, such as the use of
Allison V-1710 connecting rods and the replacement of the intercooler with ADI (Anti-Detonation Injection) (50% Distilled Water and 50%
Methanol), nearly identical in chemical composition to the Luftwaffe's wartime
MW 50 system, and similar to the
water injection system used on Pratt & Whitney engines during World War II, have allowed great increases in power output. Many of the fastest Unlimited racers increase Merlin manifold pressures as high as 145 inHg (56.6 psi, 4.8 atm) to obtain up to 2,835 kW (3,800 horsepower), achieving Mustang speeds up to 490 mph. ==Variants==