The Americas Almost all countries in North and South America have solid and intermittent
yellow lines separating traffic directions. However,
Argentina and
Uruguay have intermittent white lines separating traffic when
overtaking is permitted from both directions, and solid yellow lines when overtaking is prohibited from both directions; when overtaking is permitted from only one direction, such countries separate traffic with a combination of white and yellow lines.
Chile usually uses white lines only, except when snowy conditions are possible (in the South and on mountain roads). Then all lines are yellow.
Venezuela uses white lines.
Canada In Canada, the Volatile Organic Compound Concentration Limits for Architectural Coatings Regulations stipulate that paints for traffic markings cannot contain more than 450 g/L of
Volatile Organic Compounds. Additionally, traffic marking coatings are subject to a seasonal use restriction of 150 g/L of VOCs in effect from May 1 to October 15. Yellow lines are used to separate traffic moving in opposite directions, and white lines are used to separate traffic moving in the same direction, and on the shoulders of paved roads. On one-directional roads, a yellow line appears on the left shoulder, and a white line on the right shoulder. Passing rules are denoted by dashed lines as in the United States. In
Ontario, it is legal to cross a single solid yellow line along a straight road if the vehicle is not within 30 meters of a bridge or railway crossing. Orange painted lines are sometimes used when the direction of the road is altered temporarily for construction projects. However, the colour scheme was reversed before 1971, when white was formerly used to denote the separation of opposing traffic, and yellow lines, when used, to denote the separation of the paved road from the right-hand shoulder. Broken lines that are wider and closer together than regular broken lines are called continuity lines. Continuity lines on the left side of a lane denote that the lane is about to end and that motorists must soon merge left. Continuity lines on the right mean that the lane will continue, but traffic may merge into it ahead. In some areas, reflective markers (cat's eyes) recessed into the pavement are used, especially approaching curves in the road. A number of provinces have pavement marking test areas on major roads, to evaluate new pavement markings in relation to existing markings. In Ontario, a well-known location is the eastbound lanes of Highway 401 near Belleville. Other test sites are located on the westbound lanes on Highway 417, east of Ottawa, Highway 60 West of Renfrew, Highway 28 east of Bancroft, Highway 400 North of Honey Harbour and on Highway 37, South of Tweed. Pavement marking manufacturers from around the world supply a variety of materials for these sites to have their products evaluated and approved for use on provincial highways. Other provinces with road marking test areas include Quebec, New Brunswick, and Nova Scotia. Quebec's is outside of Montreal on Autoroute 40; in New Brunswick, the area is outside of Fredericton on Highway 2; Nova Scotia's test area is north of Halifax on Highway 102.
United States along the Marquette–Negaunee Road in
Marquette County, Michigan, shown in 1917 with its hand-painted centre line|alt=An old photograph of a bend in a road surrounded by trees and power poles. There are wooden guardrails on either side of the road, with a white-painted centre line separating the two lanes of traffic. Two old cars are approaching the curve which also has arrows to denote the direction of traffic. In the
United States, the first documented use of a painted centre line was in 1911 along
Trenton's River Road in
Wayne County, Michigan. According to the state of
Michigan, the idea of using a painted centre line was conceived in 1911 by
Edward N. Hines, the chairman of the Wayne County Board of Roads, after watching a leaky milk wagon leave a white trail along a road. Hines was the fifth recipient of the George S. Bartlett Award for Highway Progress, and was inducted posthumously in 1972 into the Michigan Transportation Hall of Honor for his innovation, and was honoured in 2011 with the first Paul Mijksenaar Design for Function Award. At some point in 1917, a white highway centre line was painted along "
Dead Man's Curve" on what is now
County Road 492 in
Marquette County, Michigan, Sawyer was inducted posthumously into the Michigan Transportation Hall of Honor in 1973. In Oregon in April 1917, a yellow centre line was painted on the
Columbia River Highway, between
Crown Point and
Multnomah Falls, at the direction of Multnomah County Sheriff's Deputy Peter Rexford. Later in 1917, the same line was continued west of Crown Point. and advocated it as a safety measure on the
Columbia River Highway, which Rexford patrolled as a traffic officer. When Multnomah County declined to fund the project, Rexford's boss, Chief Deputy Martin T. Pratt (later elected Sheriff), paid for the paint out of his own pocket so that the centre line could be painted. Rexford later described the April 1917 line as the "first yellow center line ever painted on pavement" in the United States. McCarroll soon communicated her idea to the local chamber of commerce and the Riverside County Board of Supervisors, with no success. She then took it upon herself to hand-paint a white stripe down the middle of the road, thus establishing the actual width of the lane to prevent similar accidents. In 2002, a portion of
Interstate 10 was designated and signed as "The Doctor June McCarroll Memorial Freeway" in her honour. The question of which colour to use for highway centre lines (dividing opposing traffic) in the United States was the subject of considerable debate and changing standards over a period of several decades. It was the single most controversial and most heavily debated issue resolved by the promulgation of the 1948 edition of the
Manual on Uniform Traffic Control Devices (MUTCD), which mandated white as the standard colour of centre lines nationwide. The 1961 edition of the MUTCD mandated the use of yellow for the two specific exceptions where yellow had been previously recommended but not required, and concurrently banned white in those contexts. The point was to establish a consistent
colour code in pavement markings: from now on, yellow would always delineate opposing traffic flows and white would always delineate traffic flowing in the same direction. In 2002, the
Texas A&M Transportation Institute researched the viability of converting from yellow to white centre lines for the
Transportation Research Board. The researchers conducted a survey and discovered that 75% of American drivers associate dashed yellow centre lines with dividing opposing traffic; this number rises to 85% for solid centre lines. In some areas, such as
Colorado and
Florida, black material is applied on the surface before a shorter white line is painted. This improves the contrast of the marking against "white" pavements, such as concrete or faded asphalt. In California,
Botts' dots were commonly used to mark lanes on most freeways from the mid-1960s to the mid-2010s (when the state began to transition away from them and back to using painted lines to divide lanes). Many California cities also use Botts' dots on some (or all) major arterial roads. The notable exception is the city of
Los Angeles which only uses paint. In
California and
Nevada, Botts' dots when present
are usually the lines, and no paint is used for additional markings. Exceptions include: freeways built from white concrete where painted stripes are added to make the lanes more visible through sun glare, freeways built so wide that the risk of drifting out of lane is minimal (e.g.,
Interstate 5 in the
Central Valley), and freeways in areas where it snows in the winter (since the snowploughs would scrape off the Botts' dots). In general, white lines separate traffic in the same direction, single broken lines mean passing or lane changing is allowed, single solid white lines mean lane changing is discouraged or prohibited, and double solid white lines mean it is prohibited, as it often is in
tunnels. On two-lane roads, a single broken centre line means that passing is allowed in either direction, a double solid centre line means passing is prohibited in both directions, and the combination of a solid line with a broken line means that passing is allowed only from the side with the broken line and prohibited from the side with the solid line. and
lane control signals are used to indicate which direction traffic in such lanes is supposed to travel. The solid white line on the right side is called the '' used to help cars stay in their lane during foggy conditions and help pedestrians stay off the road. Marked crosswalks are indicated at a minimum by a pair of white lines. On major boulevards, crosswalks are further highlighted by zebra stripes, which are large white rectangles in the crosswalk perpendicular to traffic. In order to maximise the longevity of
zebra crossing stripes, they are usually applied to correspond with the portions of the lane on which the wheels of a car are not usually traveling, thereby reducing wear on the markings themselves. Pavement markings are used in addition to signs in the United States to designate regular and handicap parking spaces. Regular parking spaces are normally marked with white, although other colours are used. Handicap parking spaces are required to be located within a specified distance of an entrance. Blue markings are used to indicate the parking space is reserved for persons with a
disabled parking permit. Text is painted onto the pavement to reinforce roadside signs that may be obscured for various reasons or that drivers may overlook. Common examples of such legends include "STOP" (before a solid stop line and beside a
stop sign) and "SCHOOL" (at the beginning of a
school zone). On many California streets, the speed limit is painted onto the road surface to alert drivers to a reduced speed zone. At some complex junctions,
route shield pavement markings guide drivers into the correct lane in advance of an overhead guide sign. Pavement marking test areas exist throughout the United States on various major roads.
Interstate 95 in Florida has two test locations in
Brevard County: northbound lanes, between mile markers 194 to 198, where the roadway is concrete; and southbound lanes between mile markers 162 to 163, where the roadway is asphalt.
Interstate 4 had two testing locations in
Polk County between mile markers 27 to 29 in both east- and westbound lanes.
Asia Hong Kong Road markings in Hong Kong are basically identical with the
United Kingdom, with longer dashed white lines to indicate lanes of opposing traffic or hazards, and shorter dashed white lines for lanes in the same direction. Solid double white lines indicate that drivers and cyclists must not drive or cycle on them. A solid white line with a broken white line indicates that crossing the line is allowed from the lane closer to the broken line. Double solid white lines are in place in all tunnels and underpasses. Solid yellow lines are painted along the kerbside to indicate that stopping is not allowed, unlike in the UK where they only prohibit parking. Double solid yellow lines mean stopping is not allowed at any time (parking itself is prohibited on any street with street lighting regardless of whether there are single or double yellow lines). Zig-zag lines are used on both ends of zebra crossings to indicate that drivers and cyclists must not stop unless giving way to pedestrians, and pedestrians must not cross the road otherwise than on the crossing. Road studs are also used as in the UK.
Israel In Israel, white lines are used to separate both traffic driving in the same direction and in opposite directions, while yellow lines are used to mark the shoulder of the road.
Japan area In Japan, white always separates traffic in the same direction or indicates traffic in the same direction can use a buffered area that is striped in crosshatch patterns such as at right turns on two-way roads since Japan is a country that has left-side driving. White is also used on divided expressways with a solid raised centre divider. Two-lane expressways where poles are the only physical barrier between opposing directions of travel always have yellow either side of the row of poles, and white is between the yellow striping and the poles. White is also used to denote passing allowed on other two-lane roads. Yellow indicates no passing is allowed. On all roads, yellow stripes are always solid. On expressways where there are many sharp turns and curves, seen especially in the largest cities, a yellow line indicates no passing between lanes, as follows: • Solid yellow beside solid white: no entry permitted from the lane the stripe is next to, but passing is permitted with caution. • Solid yellow beside broken white: passing is permitted from the side with the broken white line, but not from the side with the yellow line. • Solid yellow line alone: passing prohibited from either lane, used on very tight curves and in tunnels. Other markings include in the cities, destination and exit names painted in the lanes, which is done due to the very close proximity of exits, where in many cases it would be impractical to put up many overhead signs, although these are often seen approaching exits, a curved or slanted arrow points to the side of the expressway the exit will be on. A straight arrow following characters indicates the destination of the expressway. Where a solid white line appears between lanes, passing is generally allowed but with caution.
North Korea Road markings in the Democratic People's Republic of Korea are rare, but if they do exist, the lines are usually painted white, as in the
highway from Pyongyang to Nampo.
South Korea In the Republic of Korea, white always separates traffic in the same direction. White solid line means "do not change lanes", and a white double solid line has the meaning of further emphasis on that way. Dash lines allow changing lanes. Zigzag lanes mean deceleration. The yellow line is the centre line, which separates traffic in the opposite direction. Yellow solid line means "do not cross the center line, and temporary crossing of the center line for overtaking purposes is also not permitted", and yellow double solid line has the meaning of further emphasis on that way. Yellow dash lines meaning "temporary crossing the center line (=temporary wrong-way driving) for overtaking purposes is permitted". Some intersections have white broken lines at the centre. This indicates a U-turn area; drivers can make U-turns only at this place and not make a U-turn over the yellow line. Additionally, in South Korea, turning left across the centre line is prohibited, regardless of whether it be solid or dashed. Yellow dash centre line is also exist in South Korean law, but in reality, it is extremely rare to find a road section that is marked with a dash centre line in
South Korea. Centre lines of
single carriageway with 2 lanes in rural areas of South Korea is almost marking with a solid line even in sections where it is straight or where visibility is sufficient to allow temporary crossing of the centre line (=temporary wrong-way driving) for overtaking. Conversely, dash centre lines are rare than solid centre lines. As a result, inconveniences are occurring all over South Korea, with drivers having to illegally cross the centre line to overtake slow-speed vehicles, like agricultural vehicles such as cultivators and tractors, because they cannot legally overtake them in that road section. Tunnel sections of South Korean roads are almost prohibited from passing, and are marked with white solid lines that mean "do not change lane". This creates the inconvenience of not being able to legally change lanes within tunnels. Furthermore, there is criticism that white solid lines in tunnels pose a high risk of accidents than white dash lines. A blue line means bus (or tram) only. • Single line: bus-only lane at a rush hour such as 7:00–9:00 and 17:30–19:30 on weekdays • Double line: bus-only lane at additional times such as 5:00–11:0015:00–22:00 on weekdays or double line on several streets means bus-only lane all day, including weekends. • Dash line: bus-only lane. Other cars can temporarily use bus lanes to turn right into alleys or join regular lanes. Taxis can also temporarily pass through bus-only lanes to allow passengers to get on and off. • Solid line: bus-only lane. Other cars are never allowed to enter the bus-only lane. A line drawn along the side of the road: • White line: parking and stopping is allowed, but it isn't allowed on motorways and expressways. • Yellow dash line: stopping is allowed, but no parking. However, some local governments allow parking at particular times. The time available for parking is written on a sign. • Yellow single solid line: no parking and no stopping, however some local governments allow parking or stopping at particular times. The time available for parking or stopping is written on a sign. • Yellow double solid line: no parking and stopping all day. These are used near an intersection, the crosswalk, or a bus station. • Red double solid line: no parking or stopping all day because there is a fire hydrant. • Zigzag lanes mean deceleration.
Indonesia Road markings in Indonesia are almost similar to markings in
Europe and especially in the Netherlands. Markings are divided into four types, they are: • Line marking, marks that are parallel to the axis of the road. • Cross marking, mark that is crosswise to the axis of the road, such as at a stop line at a Zebra cross or at an intersection • Chevron, sign that forms a complete line which is not included in the meaning of line marking or cross marking, to indicate an area of the road surface that is not a vehicle traffic lane. • Symbol marking, mark that contain certain meanings to express warnings, orders and prohibitions to complement or confirm the intent conveyed by traffic signs or other traffic signs. The colours also represent the use: • White for line • Yellow for line (National road) • Red for Bus-way and School zone • Green for Bicycle
Europe In general European countries follow the
Vienna Convention on Road Signs and Signals, which describes what road signs and road markings shall look like. The convention has some flexibility so road markings vary somewhat between the countries. Most
European countries reserve white for routine lane markings of any kind. Yellow is used to mark forbidden parking, such as on bus stops. In most European countries, white is used to separate traffic directions, but this is not the case in Norway and Finland: Norway instead has yellow markings separating traffic directions , and Finland uses yellow lines for no passing and white when passing is allowed. Many countries use yellow, orange, or red to indicate when lanes are being shifted temporarily to make room for construction projects. In Croatia, in addition to serving as temporary signage, yellow lines are used permanently to distinguish lanes and turn directions dedicated to public transport. In France, Switzerland, and Mexico on highways the outside lines are interrupted at a regular distance which allows drivers and police to check distance between moving vehicles. In the Netherlands, Germany, Sweden, and the UK, so-called "naked roads" have been trialed, whereby all visible road markings,
kerbs, traffic lights, and signs are removed, on urban roads. When this was tested in
Seend, a village in the UK county of
Wiltshire in 2005, the
county council reported that accidents fell by a third, with motorists' speed falling by an average of 5%. It has been suggested that naked roads force drivers to make eye contact with other road users, and that it is this
nonverbal communication that is responsible for the reduction of accidents. Others have suggested that road markings, especially with middle marker, make the road look like a main road, triggering faster and more relaxed driving, while no marking makes the road look like a lower quality road. It is an experience from the introduction of marking, that at least on narrow roads and in curves, middle lines help make drivers stay on their side when meeting, and therefore reducing meeting accidents. Note that the 2005 experiment was on urban roads. In Sweden, local streets generally have no marking.
Ireland ,
County Galway In Ireland, the centre-line is usually white while the
shoulder line is usually yellow. Many rural roads are too narrow to fit a centre-line and only have a shoulder, but sometimes have no road markings. When a rural road has no markings, and grass is growing in the middle it is known as a
bóithrín (or
English: Bohereen or Boreen). In urban areas, the shoulder is not usually indicated. Double solid yellow lines indicate areas in which parking is forbidden. On most traffic light junctions, in order to improve traffic flow, a hatched yellow box is used. A vehicle cannot enter the box unless it can exit without stopping. The white centre-line can be either broken or solid. Both single solid lines and double solid white lines forbid overtaking, while dashed white lines and double dashed white lines allow vehicles to overtake each other. On motorways, same-direction dashed lines are coloured in white as is standard in much of the world. The motorway shoulder is a yellow solid line. On dual carriageways (N or R roads with two or more lanes in each direction), the shoulder is indicated by a yellow dashed line which is standard.
Netherlands markings adjacent to a traffic lane in the Netherlands In the Netherlands all general lines are white, while yellow lines are used to mark forbidden stopping (solid yellow), forbidden parking (broken yellow) and for temporarily lining at construction projects. Shoulder lines are generally interrupted outside built-up area to make the driver be aware the presence of crossing bicycles and pedestrians, driveways and stopping cars. Wider roads sometimes have a single, but in most cases have a double centre line. Interrupted centre lines mean overtaking is allowed, a solid line means overtaking is not allowed, depending on which side of a double line is solid. Smaller roads and roads where bicycles are allowed generally do not have centre lines, and many country roads have no lines at all. Sometimes there is a centre line only in sharp curves. Shoulder lines on expressways and motorways are solid to imply the general absence of crossing traffic and residential driveways, as well as the disallowance of leaving the road on places other than specified exits. Expressways always have double centre lines. Exit and acceleration lanes are separated by 'block marking'. Furthermore, several traffic signs are painted on the road, such as speed limits and warning signs.
Norway In Norway, yellow lines are used to separate traffic moving in opposite directions and on the left shoulders of paved roads, and white lines are used to separate traffic moving in the same direction, and on the right shoulders of paved roads. On roads narrower than , the centre line is removed, and the shoulder lines are broken. Short, broken lines means passing is allowed, long, broken lines means passing is allowed but dangerous, and a double yellow line means passing is forbidden. Roads with speed limits below that indicate that passing is allowed but dangerous have a very short yellow line instead of a long one. On motorways, the left shoulder is a yellow line, like in the US. Most other European countries use white lines for all these types of lines.
United Kingdom in
London, pictured from atop
the Monument in 1969 In the
UK, the first "white line" road markings appeared on a number of dangerous bends on the London-Folkestone road at Ashford, Kent, in 1914. In
England, the idea of painting a centre white line was first experimented with in 1921 in
Sutton Coldfield,
Birmingham. Following complaints by residents over reckless driving and several collisions, the Sutton Coldfield Corporation decided to paint the line on Maney Corner in the area of
Maney. In 1971, a correspondent for the
Sutton Coldfield News wrote an article in the newspaper recalling the event. During
World War II the
Pedestrians Association lobbied for the government to make it safer for pedestrians to walk during the
black out. As a result, white lines were painted on the sides of the road and pedestrians were allowed to use a small
torch. Following the successful "white line" experiment at Ashford, Kent in 1914, the use of painted lines on UK roads grew dramatically during the 1920s. In 1926 official guidelines were issued by the Ministry of Transport that defined where and how white lines on roads should be used. A broken white line in the direction of travel, where the gaps are longer than the painted lines, indicates the centre of the road and that there are no hazards specific to the design and layout of the road, i.e. no turnings, sharp bends ahead etc. A broken white line in which the gaps are shorter than the painted lines indicates an upcoming hazard. The Ministry of Transport experimented with double-line road markings for the first time on sections of the
A20 and
A3 during Easter in 1957. The markings were cautionary, and had no legal status at that time, but motorists were advised that ignoring them could weigh heavily against someone involved in an accident in their vicinity. Further, "it is in order, if safe to do so, to cross the lines only when the broken one is on your side. It is not in order to cross when the solid line is on your side or to park there." Despite the instruction about parking, it was observed that nine
bus stops were located inside prohibited parking areas. Broken yellow lines at the edge of the road mean that you cannot park, but can stop for up to 5 minutes, or more if that is needed to load and unload people or cargo. A solid yellow line on the edge of the road denotes that stopping is prohibited. During road works, temporary orange lines are often provided. These have priority over permanent markings.
Oceania Australia In Australia, road markings are typically in line with Germany and Switzerland. White lines are generally used both to separate traffic flowing in the same direction and traffic flowing in opposite directions. Double solid white centre lines may not be crossed under any circumstances unless avoiding an obstruction except in New South Wales and Western Australia where double lines may be crossed to enter or leave the roadway. Dashed lines may be crossed for overtaking, changing lanes or turning, and also in the case of double-line markings provided the dashed line is on your side of the markings. For this reason, dashed lines are usually used to mark multiple lanes travelling in one direction. Single yellow lines along road edges are used nationally to indicate "No Standing" areas not otherwise marked by signs. Solid white lines are also used to indicate kerbside parking, pedestrian and bicycle lanes, and other kerbside features. In cities with tramway networks, double yellow lines separate the tramway from the road. Yellow line markings are also used in areas that receive regular annual snowfall to provide contrast. Double-line markings are used to separate traffic flowing in opposite directions on busy roads. Solid white lines are used to mark an intersection that a driver must stop at before entering whilst obeying all right-of-way laws. Dashed white lines are used to mark an intersection at which a driver must
give way. Dashed white lines are also commonly used to indicate turns in intersections and to indicate intersections where a
diamond turn is possible (intersections in which two cars travelling in opposite directions turn to the same direction of travel as each other without coming into contact). Materials used are waterborne paint, thermoplastics, and cold-applied plastic (PMMA), all with glass beads. Bead is generally 1mm for longitudinal marking. Currently moving to performance-specified contracts with the primary performance indicator being retro-reflectivity measured with geometry instruments. Intervention levels vary generally from 100 to 150 mcd/lux/m2 (from 0.029 to 0.044 foot-lamberts).
New Zealand Although
New Zealand follows the convention of a solid yellow line to indicate no passing on roads with two-way traffic, it uses dashed white lines with a gap to indicate when passing against opposing traffic is allowed on two-lane roads
and shorter ones to separate lanes going in the same direction. The New Zealand convention followed the USA MUTCD convention common between 1961 and the early 1970s. New Zealand road markings are governed/standardised by Part 2 of the Manual Of Traffic Signs And Markings (MOTSAM). ==References==