There are many variations amongst post mills.
Sunk post mill The earliest post mills were quite small, and this led to problems with stability as they were liable to blow down in strong winds. A solution was found by burying the bottom of the
trestle in a mound of earth. The last sunk post mills in England were at
Warton,
Lancashire, and
Essington,
Staffordshire.
Open trestle post mill As mills were made bigger, it was found that the trestle did not need to be buried. Thus the open trestle post mills were built. The oldest surviving is at
Great Gransden, Cambridgeshire. Others exist in the UK at
Bourn, Cambridgeshire;
Great Chishill, Cambridgeshire;
Nutley, Sussex and
Chillenden, Kent. Open trestle post mills are also found in France, Belgium, the Netherlands, Germany and in
New England, USA. Image:Chillenden post mill - geograph.org.uk - 677916.jpg|Chillenden post mill, built in 1868. Image:Chillenden mill.jpg|Chillenden open trestle post mill (another view).
Post mill with roundhouse The space around the trestle could be used for storage, but was open to the weather. Mill owners started to build
roundhouses around the trestles, and later mills were built with a roundhouse from new. This had the dual advantage of creating a covered storage area and protecting the trestle from bad weather. In
Suffolk,
millwrights would build post mills mounted on tall, two or three storey roundhouses, as at
Saxtead Green. Image:Friston Post Mill - geograph.org.uk - 1970480.jpg|Friston Post Mill, near Friston, Suffolk. File:Aurora standerdmolen Baexem. Limburg 1845 Limburgse molendag 2019.jpg|Aurora Post Mill (1845)
Baexem, Netherlands Image:Garboldisham Post Mill - External View - geograph.org.uk - 2248810.jpg|Garboldisham Post Mill; the mill is complete inside, externally only missing the sails. Image:Oldland Mill.jpg|Post mill with roundhouse. Image:Saxtead Green Post Mill - geograph.org.uk - 514428.jpg|Saxtead Green Post Mill roundhouse is partially obscured by a hedgerow.
Midlands post mill In the Midlands and North West of England, the top of the roundhouse had a curb, and rollers affixed to the mill body enabled the roundhouse to bear some of the weight of the mill. Examples of Midlands post mills extant include Danzey Green mill, (preserved at
Avoncroft Museum of Historic Buildings) and the mill at
Wrawby, Lincolnshire.
Alternative ways to protect the trestle In eastern Europe, instead of a roundhouse an "apron" was fitted to the bottom of the body of the mill, enclosing the trestle and thereby affording protection from the weather. Image:14th century post mill.jpg|Medieval illustration of a sunk post mill. Image:Madingley Windmill.jpg|Midlands post mill. Image:Post_mill_-_Bockwindmühle_-_1638_-_open_air_museum_Cloppenburg_-_Germany.jpg|Post mill, rebuilt in the open-air museum at Cloppenburg, Germany. Image:Svaneke post mill.jpg|Wooden post mill in Svaneke, Denmark. Image:Wrawby post mill - four sails again - geograph.org.uk - 962858.jpg|Wrawby post mill – restored to have four sails. File:Bierzgłowo wiatrak.jpg|A
Polish post mill (
Bierzgłowo near
Toruń).
Hollow Post mill Some post mills are hollow post mills. In these mills the main post is bored to take a driveshaft, similar to an Upright Shaft in a
smock or
tower mill. This enables the mill to drive machinery in the base or roundhouse. Hollow post mills were not common in the United Kingdom. In the Netherlands, they are called
Wipmolen and were mostly used for drainage. In France, the
Moulin Cavier was a type of hollow post mill used for corn milling. Image:Thorpeness windmill.jpg|Hollow post
Thorpeness Windmill. Image:Groot-Ammers Graaflandse Molen foto 2.jpg|Wipmolen Image:Moulin des Aigremonts, Bléré, 37, juin 2008, face.jpg|Moulin Cavier.
Composite mill A few mills looked like post mills, but were not post mills. These composite mills often had a post mill body mounted on a short tower resembling a roundhouse, as at
Banham and
Thornham in Norfolk. Composite mills lack the central post on which the body of the post mill is mounted and turns upon to enable the mill to face the wind.
Paltrok mill In the
Netherlands and
Germany, a variety of mill called the paltrok (Low German spelling
Paltrock, from High German
Pfalzrock (
palisade skirt); the shape of the millhouse resembles that kind of garment) was built. Though similar in name and appearance, Dutch and German paltrok mills differ in historical and technical regard. The Dutch
paltrok mill was invented around 1600 and specifically designed for sawing wood. Several hundred have existed of this type of windmill; however, only five paltrok mills remain in the
Netherlands, at
Zaanse Schans,
Haarlem,
Zaandam,
Amsterdam and at the
Netherlands Open Air Museum,
Arnhem. Dutch paltrok mills are, like post windmills, supported on a central wooden post around which the entire millhouse rotates. The central post, however, is short and, to provide stability, a rim bearing is added on a brick base, on which the millhouse rotates with numerous rollers. Side extensions protect the sawing floor and workmen from the weather. German
paltrok mills were commonly converted from post mills where the post and trestle were replaced by a wooden or iron rim bearing, set into the ground or on a brick base. The millhouse was enlarged and supported on this rim by numerous rollers or small wheels. These mills are technically composite mills although the tower is very short and of large diameter. This type of mill provided more internal space than a post mill and was cheaper than the alternative of erecting a
smock mill. File:Paltrok openluchtmuseum.jpg|Paltrok mill
Mijn Genoegen in the
Netherlands Open Air Museum File:Schönewalde Mühle.jpg|Paltrock mill at Schönewalde in
Elbe-Elster, Brandenburg, Germany == Citations ==