Intel QuickPath Interconnect

Although sometimes called a "bus", QPI is a scalable interconnect fabric with dynamic routing capabilities. It was designed to compete with HyperTransport that had been used by Advanced Micro Devices (AMD) since around 2003. Intel developed QPI at its Massachusetts Microprocessor Design Center (MMDC) by members of what had been the Alpha Development Group, which Intel had acquired from Compaq and HP and in turn originally came from Digital Equipment Corporation (DEC). Intel first delivered it for desktop processors in November 2008 on the Intel Core i7-9xx and X58 chipset. It was released in Xeon processors code-named Nehalem in March 2009 and Itanium processors in February 2010 (code named Tukwila). It was supplanted by the Intel Ultra Path Interconnect starting in 2017 on the Xeon Skylake-SP platforms. ==Implementation==

component in Intel's Nehalem microarchitecture. The QPI is an element of a system architecture that Intel calls the QuickPath architecture that implements what Intel calls QuickPath technology. In its simplest form on a single-processor motherboard, a single QPI is used to connect the processor to the IO Hub (e.g., to connect an Intel Core i7 to an X58). In more complex instances of the architecture, separate QPI link pairs connect one or more processors and one or more IO hubs or routing hubs in a network on the motherboard, allowing all of the components to access other components via the network. As with HyperTransport, the QuickPath Architecture assumes that the processors will have integrated memory controllers, and enables a non-uniform memory access (NUMA) architecture. Each QPI comprises two 20-lane point-to-point data links, one in each direction (full duplex), with a separate clock pair in each direction, for a total of 42 signals. Each signal is a differential pair, so the total number of pins is 84. The 20 data lanes are divided onto four "quadrants" of 5 lanes each. The basic unit of transfer is the 80-bit flit, which has 8 bits for error detection, 8 bits for "link-layer header", and 64 bits for data. One 80-bit flit is transferred in two clock cycles (four 20-bit transfers, two per clock tick.) QPI bandwidths are advertised by computing the transfer of 64 bits (8 bytes) of data every two clock cycles in each direction. Although the initial implementations use single four-quadrant links, the QPI specification permits other implementations. Each quadrant can be used independently. On high-reliability servers, a QPI link can operate in a degraded mode. If one or more of the 20+1 signals fails, the interface will operate using 10+1 or even 5+1 remaining signals, even reassigning the clock to a data signal if the clock fails. In post-2009 single-socket chips starting with Lynnfield, Clarksfield, Clarkdale and Arrandale, the traditional northbridge functions are integrated into these processors, which therefore communicate externally via the slower DMI and PCI Express interfaces. Thus, there is no need to incur the expense of exposing the (former) front-side bus interface via the processor socket. Although the core–uncore QPI link is not present in desktop and mobile Sandy Bridge processors (as it was on Clarkdale, for example), the internal ring interconnect between on-die cores is also based on the principles behind QPI, at least as far as cache coherency is concerned. ==Frequency specifications==

Being a synchronous circuit the QPI operates at a clock rate of 2.4 GHz, 2.93 GHz, 3.2 GHz, 3.6 GHz, 4.0 GHz or 4.8 GHz (3.6 GHz and 4.0 GHz frequencies were introduced with the Sandy Bridge-E/EP platform and 4.8 GHz with the Haswell-E/EP platform). The clock rate for a particular link depends on the capabilities of the components at each end of the link and the signal characteristics of the signal path on the printed circuit board. The non-extreme Core i7 9xx processors are restricted to a 2.4 GHz frequency at stock reference clocks. Bit transfers occur on both the rising and the falling edges of the clock, so the transfer rate is double the clock rate. Intel describes the data throughput (in GB/s) by counting only the 64-bit data payload in each 80-bit flit. However, Intel then doubles the result because the unidirectional send and receive link pair can be simultaneously active. Thus, Intel describes a 20-lane QPI link pair (send and receive) with a 3.2 GHz clock as having a data rate of 25.6 GB/s. A clock rate of 2.4 GHz yields a data rate of 19.2 GB/s. More generally, by this definition a two-link 20-lane QPI transfers eight bytes per clock cycle, four in each direction. The rate is computed as follows: :3.2 GHz :× 2 bits/Hz (double data rate) :× 16(20) (data bits/QPI link width) :× 2 (unidirectional send and receive operating simultaneously) :÷ 8 (bits/byte) := 25.6 GB/s ==Protocol layers==

QPI is specified as a five-layer architecture, with separate physical, link, routing, transport, and protocol layers. In devices intended only for point-to-point QPI use with no forwarding, such as the Core i7-9xx and Xeon DP processors, the transport layer is not present and the routing layer is minimal. ; Physical layer : The physical layer comprises the actual wiring and the differential transmitters and receivers, plus the lowest-level logic that transmits and receives the physical-layer unit. The physical-layer unit is the 20-bit "phit." The physical layer transmits a 20-bit "phit" using a single clock edge on 20 lanes when all 20 lanes are available, or on 10 or 5 lanes when the QPI is reconfigured due to a failure. Note that in addition to the data signals, a clock signal is forwarded from the transmitter to receiver (which simplifies clock recovery at the expense of additional pins). ; Link layer : The link layer is responsible for sending and receiving 80-bit flits. Each flit is sent to the physical layer as four 20-bit phits. Each flit contains an 8-bit CRC generated by the link layer transmitter and a 72-bit payload. If the link layer receiver detects a CRC error, the receiver notifies the transmitter via a flit on the return link of the pair and the transmitter resends the flit. The link layer implements flow control using a credit/debit scheme to prevent the receiver's buffer from overflowing. The link layer supports six different classes of message to permit the higher layers to distinguish data flits from non-data messages primarily for maintenance of cache coherence. In complex implementations of the QuickPath architecture, the link layer can be configured to maintain separate flows and flow control for the different classes. It is not clear if this is needed or implemented for single-processor and dual-processor implementations. ; Routing layer : The routing layer sends a 72-bit unit consisting of an 8-bit header and a 64-bit payload. The header contains the destination and the message type. When the routing layer receives a unit, it examines its routing tables to determine if the unit has reached its destination. If so it is delivered to the next-higher layer. If not, it is sent on the correct outbound QPI. On a device with only one QPI, the routing layer is minimal. For more complex implementations, the routing layer's routing tables are more complex, and are modified dynamically to avoid failed QPI links. ; Transport layer : The transport layer is not needed and is not present in devices that are intended for only point-to-point connections. This includes the Core i7. The transport layer sends and receives data across the QPI network from its peers on other devices that may not be directly connected (i.e., the data may have been routed through an intervening device.) the transport layer verifies that the data is complete, and if not, it requests retransmission from its peer. ; Protocol layer : The protocol layer sends and receives packets on behalf of the device. A typical packet is a memory cache row. The protocol layer also participates in maintenance of cache coherence by sending and receiving relevant messages. ==See also==