Track gauge

The most common use of the term "track gauge" refers to the transverse distance between the inside surfaces of the two load-bearing rails of a railway track, usually measured at to below the top of the rail head to clear worn corners and allow for rail heads having sloping sides. The term derives from the "gauge", a metal bar with a precisely positioned lug at each end that track crews use to ensure the actual distance between the rails lies within tolerances of a prescribed standard; on curves, for example, the spacing is wider than normal. Deriving from the name of the bar, the distance between these rails is also referred to as the track gauge. ==Choice of gauge==

Early track gauges The earliest form of railway was a wooden wagonway, along which single wagons were manhandled, almost always in or from a mine or quarry. Initially, the wagons were guided by human muscle power; subsequently, by various mechanical methods. Timber rails wore rapidly; later, flat cast-iron plates were provided to limit the wear. In some localities, the plates were made L-shaped, with the vertical part of the L guiding the wheels; this is generally referred to as a "plateway". Flanged wheels eventually became universal, and the spacing between the rails had to be compatible with that of the wagon wheels. As the guidance of the wagons was improved, short strings of wagons could be connected and pulled by teams of horses, and the track could be extended from the immediate vicinity of the mine or quarry, typically to a navigable waterway. The wagons were built to a consistent pattern, and the track was made to suit the needs of the horses and wagons; the gauge was the more critical factor. The Penydarren Tramroad of 1802 in South Wales, a plateway, spaced these at over the upstands. The Penydarren Tramroad probably made the first journey by locomotive in 1804, and it was successful for the locomotive but unsuccessful for the track: the plates were not strong enough to carry its weight. A considerable step forward was made when cast-iron edge rails were first employed; these had the major axis of the rail section oriented vertically, giving a much stronger section to resist bending forces, and the introduction of fish-belly rails further improved this. Edge rails required a close match between rail spacing and wheelset configuration, reinforcing the importance of the gauge. Railways were still seen as local concerns: there was no appreciation of a future connection to other lines, and the choice of track gauge remained a pragmatic decision based on local requirements and prejudices, probably determined by existing local designs of (road) vehicles. Thus, the Monkland and Kirkintilloch Railway (1826) in the West of Scotland used ; the Dundee and Newtyle Railway (1831) in the north-east of Scotland adopted ; the Redruth and Chasewater Railway (1825) in Cornwall chose . The Arbroath and Forfar Railway opened in 1838 with a gauge of , and the Ulster Railway of 1839 used . The Stockton and Darlington line was very successful, and when the Liverpool and Manchester Railway, the first intercity line, was opened in 1830, it used the same gauge. It too was very successful, and the gauge, widened to ==Terminology==

Standard gauge is generally known world-wide as being . Terms such as broad gauge and narrow gauge do not have any fixed meaning beyond being materially wider or narrower than standard. In British practice, the space between the rails of a track is colloquially referred to as the "four-foot", and the space between two tracks the "six-foot", descriptions relating to the respective dimensions. Standard gauge In modern usage, the term "standard gauge" refers to . The standard gauge is dominant in most countries, including those in North America, most of Western Europe, North Africa, the Middle East, and China. Broad gauge In modern usage, the term "broad gauge" generally refers to track spaced significantly wider than . Broad gauge is the dominant gauge in countries in the Indian subcontinent, the former Soviet Union (CIS states, Baltic states, Georgia, and Ukraine), Mongolia, Finland (which still uses the original Russian imperial gauge of 1524mm), Spain, Portugal, Argentina, Chile, and Ireland. It is also used for the suburban railway systems in South Australia, and Victoria, Australia. Medium gauge The term "medium gauge" had different meanings throughout history, depending on the local dominant gauge in use. In 1840s, the Irish gauge was considered a medium gauge compared to Brunel's broad gauge and the narrow gauge, which became the modern standard gauge. Narrow gauge In modern usage, the term "narrow gauge" generally refers to track spaced significantly narrower than . Narrow gauge is the dominant or second-dominant gauge in countries in Southern, Central, and East Africa; Southeast Asia; Japan; Taiwan; the Philippines; and Central and South America. During the period known as the "battle of the gauges", Stephenson's standard gauge was commonly known as "narrow gauge", while Brunel's railways' gauge was termed "broad gauge". Many narrow gauge railways were built in mountainous regions such as Wales, the Rocky Mountains of North America, Central Europe, and South America. Industrial railways and mine railways across the world are often narrow gauge. Sugar cane and banana plantations are mostly served by narrow-gauge. Minimum gauge Very narrow gauges of under were used for some industrial railways in space-restricted environments such as mines or farms. The French company Decauville developed and tracks, mainly for mines; Heywood developed gauge for estate railways. The most common minimum gauges were , , , , or . Break of gauge in 1843Through operation between railway networks with different gauges was originally impossible; goods had to be transshipped, and passengers had to change trains. This was obviously a major obstacle to convenient transport, and in Great Britain, it led to political intervention. On narrow-gauge lines, rollbocks or transporter wagons are used: standard-gauge wagons are carried on these special vehicles, generally with wider-rail tracks to enable the vehicles to roll on and off at transfer points. On the Transmongolian Railway, Russia and Mongolia use while China uses the standard gauge of 1,435 mm. At the border, each carriage is lifted and its bogies are changed. The operation can take several hours for a whole train of many carriages. Other examples include crossings into or out of the former Soviet Union: Ukraine/Slovakia border on the Bratislava–Lviv train, and the Romania/Moldova border on the Chișinău–Bucharest train. A system developed by Talgo and Construcciones y Auxiliar de Ferrocarriles (CAF) of Spain uses variable gauge wheelsets; at the border between France and Spain, through passenger trains are drawn slowly through an apparatus that alters the gauge of the wheels, which slide laterally on the axles. A similar system is used between China and Central Asia, and between Poland and Ukraine, employing the SUW 2000 and INTERGAUGE variable-axle systems. China and Poland use standard gauge, while Central Asia and Ukraine use . ==Dual gauge==

When individual railway companies have chosen different gauges and have needed to share a route where space on the ground is limited, mixed gauge (or dual gauge) track, in which three (sometimes four) rails are supported in the same track structure, can be necessary. The most frequent need for such a track was at the approaches to city terminals or at break-of-gauge stations. Tracks with multiple gauges entail considerable construction costs (including signaling work) and complex track maintenance, and may require speed restrictions. They are therefore built only when necessary. If the difference between the two gauges is large enough – for example between and – three-rail dual-gauge is possible, but if not – for example between and – four rails must be used. Dual-gauge rail lines occur (or have occurred) in Argentina, Australia, Brazil, Japan, North Korea, Spain, Switzerland, Tunisia, and Vietnam. , and track at Didcot Railway Museum, England On the GWR, there was an extended period between political intervention in 1846 that prevented major expansion of its broad gauge and the final gauge conversion to standard gauge in 1892. During this period, many locations' practical requirements necessitated mixed-gauge operation, and in station areas, the track configuration was extremely complex. This was compounded by the common rail being on the platform side at stations; therefore, in many cases, standard-gauge trains needed to be switched from one side of the track to the other at the approach. A special fixed-point arrangement was devised for the purpose, with a simple enough track layout. In some cases, mixed-gauge trains were operated with wagons of both gauges. For example, MacDermot wrote: In November 1871 a novelty in the shape of a mixed-gauge goods train was introduced between Truro and Penzance. It was worked by a narrow-gauge engine, and behind the narrow-gauge trucks came a broad-gauge match-truck with wide buffers and sliding shackles, followed by the broad-gauge trucks. Such trains continued to run in West Cornwall until the abolition of the Broad Gauge; they had to stop or come down to walking pace at all stations where fixed points existed and the narrow portion side-stepped to right or left. Triple gauge In rare situations, three different gauges may converge onto a rail yard, and triple-gauge track is needed to meet the operational needs of the break-of-gauge station – most commonly where there is insufficient space to do otherwise. Construction and operation of triple-gauge track and its signaling, however, involves immense cost and disruption, and is undertaken when no other alternative is available. ==Nominal track gauge==

The nominal track gauge is the distance between the inner faces of the rails. In current practice, it is specified at a certain distance below the rail head, as the inner faces of the rail head (the gauge faces) are not necessarily vertical. Some amount of tolerance is necessarily allowed from the nominal gauge to allow for wear, etc.; this tolerance is typically greater for track limited to slower speeds, and tighter for track where higher speeds are expected (as an example, in the US the gauge is allowed to vary between to for track limited to , while track is allowed only to . Given the allowed tolerance, it is common practice to widen the gauge slightly in curves, particularly those of shorter radius (which are inherently slower-speed curves). Rolling stock on the network must have running gear (wheelsets) compatible with the gauge; therefore, the gauge is a key parameter in determining interoperability, but there are many others – see below. In some cases, in the earliest days of railways, the railway company saw itself as an infrastructure provider only, and independent haulers provided wagons suited to the gauge. Colloquially, the wagons might be referred to as "four-foot gauge wagons", say, if the track had a gauge of four feet. This nominal value does not equate to the flange spacing, as some freedom is allowed for. An infrastructure manager might specify new or replacement track components at a slight variation from the nominal gauge for pragmatic reasons. ==Units==

The gauge is defined in imperial units, metric units or SI units. Imperial units were established in the United Kingdom by the Weights and Measures Act 1824. The United States customary units for length did not agree with the imperial system until 1959, when one international yard was defined as 0.9144 meters and, as derived units, 1 foot (= yd) as 0.3048 meter and 1 inch (= yd) as 25.4 mm. The list shows the imperial and other units that have been used for track gauge definitions: ==Temporary way – permanent way==

cavern where the Manhattan terminus of the standard gauge Long Island Rail Road was built. A temporary way is the temporary track often used for construction, to be replaced by the permanent way (the structure consisting of the rails, fasteners, sleepers/ties and ballast (or slab track), plus the underlying subgrade) when construction nears completion. In many cases, narrow-gauge track is used temporarily because of the convenience of laying it and relocating it over unimproved ground. In restricted spaces such as tunnels, the temporary arrangement might be double-track, even though the tunnel will ultimately be single-track. The Airport Rail Link in Sydney had construction trains of gauge, which were replaced by permanent tracks of gauge. During World War I, trench warfare led to a relatively static disposition of infantry, requiring considerable logistics to bring them support staff and supplies (food, ammunition, earthworks materials, etc.). Both sides established dense light railway networks using temporary narrow-gauge track sections for this purpose. In 1939, it was proposed to construct the western section of the Yunnan–Burma Railway using a gauge of , since such a tiny or "toy" gauge facilitates the tightest of curves in difficult terrain. ==Maintenance standards==

Infrastructure owners specify permitted variances from the nominal gauge and the required interventions to be taken when a non-compliant gauge is detected. For example, the Federal Railroad Administration in the US specifies that the actual gauge of a 1,435 mm track that is rated for a maximum of must be between and . ==Advantages and disadvantages of different track gauges==

Speed, capacity, and economy are generally objectives of rail transport, but there is often an inverse relationship between these priorities. There is a common misconception that a narrower gauge permits a tighter turning radius, but for practical purposes, there is no meaningful relationship between gauge and curvature. Construction cost Narrower gauge railways usually cost less to build because they are usually lighter in construction, using smaller cars and locomotives (smaller loading gauge), as well as smaller bridges, smaller tunnels (smaller structure gauge). Narrow gauge is thus often used in mountainous terrain, where the savings in civil engineering work can be substantial. It is also used in sparsely populated areas, with low potential demand, and for temporary railways that will be removed after short-term use, such as for construction, the logging industry, the mining industry, or large-scale construction projects, especially in confined spaces (see Temporary way – permanent way). For temporary railways which will be removed after short-term use, such as those used in logging, mining, or large-scale construction projects, especially in confined spaces, such as when constructing the Channel Tunnel, a narrow-gauge railway is substantially cheaper and easier to install and remove. Such railways have almost vanished due to the capabilities of modern trucks. In many countries, narrow-gauge railways were built as branch lines to feed traffic into standard-gauge lines because of lower construction costs. The choice was often not between a narrow-gauge railway and a standard-gauge railway, but between a narrow-gauge railway and none at all. Broader gauge railways are generally more expensive to build, because they are usually heavier in construction, use larger cars and locomotives (larger loading gauge), as well as larger bridges, larger tunnels (larger structure gauge). But broader gauges offer higher speed and capacity. For high-traffic routes, greater capacity may more than offset the higher initial construction cost. Interchangeability The value or utility a user derives from a good or service depends on the number of users of compatible products – the "network effect" in economics. Network effects are typically positive, resulting in a given user deriving more value from a product as other users join the same network. At national levels, the network effect has resulted in commerce extending beyond regional and national boundaries. Increasingly, many governments and companies have made their railway engineering and operational standards compatible to achieve interchangeability – hence faster, longer-distance train operation. A major barrier to achieving interchangeability, however, is path dependence – in this context the persistence of an already adopted standard to which equipment, infrastructure and training has become aligned. Since adopting a new standard is difficult and expensive, continuing with an existing standard can remain attractive, unless longer-term benefits are given appropriate weight. An example of the consequences of path dependence is the persistence in the United Kingdom – the earliest nation to develop and adopt railway technologies – of structure gauges that are too small to allow the larger rolling stock of continental Europe to operate in the UK. The reduced cost, greater efficiency, and greater economic opportunity offered by the use of a common standard have resulted in the historical multitude of track gauges dwindling to a small number that predominate worldwide. When interchangeability has not been achieved, freight and passengers must be transferred through time-consuming procedures requiring manual labor and substantial capital expenditure. Some bulk commodities, such as coal, ore, and gravel, can be mechanically transshipped. Still, even this is time-consuming, and the equipment required for the transfer is often complex to maintain. If rail lines of different gauges coexist in a network and a break of gauge exists, it is difficult in times of peak demand to move rolling stock to where it is needed. Sufficient rolling stock must be available to meet a narrow-gauge railway's peak demand, which might be greater in comparison to a broader-gauge network, and the surplus equipment generates no cash flow during periods of low demand. In regions where narrow-gauge lines form a small part of the rail network (as was the case on Russia's Sakhalin Railway), there is an extra cost associated with designing, manufacturing, or importing narrow-gauge equipment. Solutions to interchangeability problems include bogie exchanges, a rollbock system, dual gauge, variable gauge, or gauge conversion. == Dominant railway gauges ==

More than half of the world's railways are built to . New railways have been built in Africa to standard gauge. Most of the narrow-gauge railways in India are being converted to the dominant, broad-gauge. Prevalence Total for each group of gauges in 2020: ==Future==

Further convergence of rail gauge use seems likely, as countries seek to build interoperable networks and international organizations seek to build macro-regional and continental networks. Almost all new high-speed rail lines are built to standard gauge, except in Uzbekistan and Russia. Europe The European Union has set out to develop interoperable freight and passenger rail networks across its area, and is seeking to standardize gauge, signaling, and electrical power systems. EU funds have been dedicated to assist Lithuania, Latvia, and Estonia in the building of some key railway lines (Rail Baltica) of standard gauge, and to assist Spain and Portugal in the construction of high-speed lines to connect Iberian cities and to the French high-speed lines. The EU has developed plans for improved freight rail links between Spain, Portugal, and the rest of Europe. Trans-Asian Railway The United Nations Economic and Social Commission for Asia and the Pacific (UNESCAP) is planning a Trans-Asian Railway that will link Europe and the Pacific, with a Northern Corridor from Europe to the Korean Peninsula, a Southern Corridor from Europe to Southeast Asia, and a North–South corridor from Northern Europe to the Persian Gulf. All of these would encounter changes in gauge as they cross Asia. Current plans call for mechanized facilities at the breaks of gauge to move containers from train to train, rather than for widespread gauge conversion. The Northern Corridor through Russia has been operating since before the year 2000, with increasing volumes to China–Europe. The Americas • 2008: Proposed link between Venezuela and Colombia • 2008: Venezuela via Brazil to Argentina – standard gauge • 2008: A proposed metre gauge line across Southern Paraguay to link Argentina at Resistencia to Brazil at Cascavel; both those lines are , and the new line would allow "bioceanic" running from the Atlantic port of Paranaguá in Brazil to that of Antofagasta in Chile on the Pacific. Africa The East African Railway Master Plan is a proposal for rebuilding and expanding railway lines connecting Ethiopia, Djibouti, Kenya, Uganda, Rwanda, Burundi, Tanzania, South Sudan and beyond. The plan is managed by infrastructure ministers from participating East African Community countries in association with transport consultation firm CPCS Transcom. Older railways are of or gauge. Newly rebuilt lines will use standard gauge. Regular freight and passenger services began on the standard gauge Mombasa–Nairobi railway in 2017 and on the standard gauge Addis Ababa–Djibouti railway in 2018. Lines for iron ore to Kribi in Cameroon are likely to be with a likely connection to the same port from the Cameroon system. Nigeria's railways are mostly Cape gauge. The Lagos–Kano Standard Gauge Railway is a gauge conversion project by the Nigerian Government to create a north–south standard gauge rail link. The first converted segment, between Abuja and Kaduna, was completed in July 2016. The African Union has a 50-year plan to connect the capital cities and major centers by high-speed railways. == Timeline ==