| (standard) | (Vogue LSE) }} | (SWB) | (LWB) }} }} The first-generation Range Rover was produced between 1970 and 1996. It was available only in a 2-door body until 1981. (Before then, 4-door models had been produced by specialist firms). Unlike other
4x4s such as the
Jeep Wagoneer, the original Range Rover was not designed as a luxury vehicle. It was up-market compared to preceding Land Rover models, but the early Range Rovers had fairly basic, utilitarian, interiors with
vinyl seats and plastic dashboards that were designed to be washed down with a hose. Convenience features such as
power steering, carpeted floors, air conditioning, cloth/leather seats, and wooden interior trim were fitted later. The Range Rover was a
body-on-frame design with a box section ladder type
chassis, like the contemporary
Series Land Rovers. The Range Rover used
coil springs as opposed to
leaf springs, permanent
four-wheel drive, and four-wheel
disc brakes. The Range Rover was originally powered by various
Rover V8 engines and diesel engines. Originally, the Range Rover was fitted with a detuned version of the Buick-derived
Rover V8 engine. In 1984, the engine was fitted with
Lucas fuel injection, boosting power to . The 3.5-litre (3,528 cc) engine was bored out to a
displacement of 3.9 litres (3,947 cc) for the 1990 model year, and 4.2 litres (4,215 cc) in 1992 for the 108-inch Long Wheelbase Vogue LSE (County LWB in North America). One of the first significant changes came in 1981, with the introduction of a four-door body. In 1988, LR introduced a 2.4-litre turbodiesel (badged Vogue Turbo D) with , manufactured by Italian
VM Motori. The diesel project was codenamed project Beaver. In 1990 project Otter was unveiled, a mildly tuned 2.5-litre, version of the 'Beaver' 2.4. In 1992, Land Rover finally introduced their own diesel engines in the Range Rover, beginning with the 200TDi, first released in the
Land Rover Discovery and following in 1994, the 300 TDi with the same maximum output. The classic was known as the Range Rover until almost the end of its production when Land Rover introduced the name
Range Rover Classic to distinguish it from its successors. The original model served as the basis for the 1989 introduced 1st generation Discovery (directly based on the standard (short) wheelbase Range Rover), and for the second generation Range Rover, based on the LWB chassis of the Classic.
Jaguar-Rover-Australia began assembly of the Range Rover from
CKD kits at its
Enfield plant, in
New South Wales, Australia in 1979. Government increases in the tariff on parts led to the discontinuation of Australian assembly in 1983. Range Rover (15929079702).jpg|Range Rover 3-door (rear) Range Rover front 20080331.jpg|Range Rover 5-door estate 1989 Land Rover Range Rover 5-door wagon (2011-06-15) 02.jpg|Range Rover 5-door estate (rear)
Specialist vehicles The first-generation Range Rover served as the base for specialist utility vehicles. These included the Carmichaels International six-wheel
Fire Tender. This was a two-door model with an extended chassis and a third "lazy" axle added. Designed for small airfield use, it had a water-pump mounted on the front bumper driven directly by the V8's crankshaft. The
MoD purchased them for the RAF, this version was called the
TACR2. Carmichaels was contracted to supply the modified chassis and the fire-fighting body was supplied and mounted by Gloster-Saro. These were four-door versions using an internally mounted water-pump driven by a gearbox
PTO. At least one of these (at
Duxford IWM) has been converted into a full 6WD by linking a drive-through unit to the two rear axles == Second generation (1994) ==