The first
PC motherboards with support for RDRAM debuted in late 1999, after two major delays. RDRAM was controversial during its widespread use by Intel for having high licensing fees, high cost, being a proprietary standard, and low performance advantages for the increased cost. RDRAM and
DDR SDRAM were involved in a standards war. PC-800 RDRAM operated at 400
MHz and delivered 1600
MB/s of
bandwidth over a 16-bit bus. It was packaged as a 184-pin
RIMM (
Rambus in-line memory module)
form factor, similar to a
DIMM (dual in-line memory module). Data is transferred on both the rising and falling edges of the clock signal, a technique known as
DDR. To emphasize the advantages of the DDR technique, this type of RAM was marketed at speeds twice the actual clock rate, i.e. the 400 MHz Rambus standard was named PC-800. This was significantly faster than the previous standard, PC-133
SDRAM, which operated at 133 MHz and delivered 1066 MB/s of bandwidth over a 64-bit bus using a 168-pin
DIMM form factor. Moreover, if a mainboard has a
dual- or
quad-channel memory subsystem, all of the memory channels must be upgraded simultaneously. 16-bit modules provide one channel of memory, while 32-bit modules provide two channels. Therefore, a dual-channel mainboard accepting 16-bit modules must have RIMMs added or removed in pairs. A dual-channel mainboard accepting 32-bit modules can have single RIMMs added or removed as well. Note that the later 32-bit modules had 232 pins as compared to the older 184-pin 16-bit modules.
Module specifications Continuity modules The design of many common Rambus memory controllers dictated that memory modules be installed in sets of two. Any remaining open memory slots must be filled with continuity RIMMs (CRIMMs). These modules provide no extra memory and only served to propagate the signal to
termination resistors on the motherboard instead of providing a dead end, where signals would reflect. CRIMMs appear physically similar to regular RIMMs, except that they lack
integrated circuits (and their heat-spreaders).
Performance Compared to other contemporary standards, Rambus showed an increase in latency, heat output, manufacturing complexity, and cost. Because of more complex interface circuitry and increased number of memory banks, RDRAM die size was larger than that of contemporary SDRAM chips, resulting in a 10–20% price premium at 16 Mbit densities (adding about a 5% penalty at 64 Mbit). Note that the most common RDRAM densities are 128 Mbit and 256 Mbit. PC-800 RDRAM operated with a latency of 45
ns, more than that of other SDRAM varieties of the time. RDRAM memory chips also put out significantly more heat than SDRAM chips, necessitating
heat spreaders on all RIMM devices. RDRAM includes additional circuitry (such as packet demultiplexers) on each chip, increasing manufacturing complexity compared to SDRAM. RDRAM was also up to four times more expensive than PC-133 SDRAM due to a combination of higher manufacturing costs and high license fees. PC-2100
DDR SDRAM, introduced in 2000, operated with a clock rate of 133 MHz and delivered 2100 MB/s over a 64-bit bus using a 184-pin DIMM form factor. With the introduction of the Intel 840 (Pentium III),
Intel 850 (Pentium 4), Intel 860 (Pentium 4 Xeon) chipsets, Intel added support for dual-channel PC-800 RDRAM, doubling bandwidth to 3200 MB/s by increasing the bus width to 32 bits. This was followed in 2002 by the Intel 850E chipset, which introduced PC-1066 RDRAM, increasing total dual-channel bandwidth to 4200 MB/s. In 2002, Intel released the E7205 Granite Bay chipset, which introduced dual-channel DDR support (for a total bandwidth of 4200 MB/s) at a slightly lower latency than competing RDRAM. The bandwidth of Granite Bay matched that of the i850E chipset using PC-1066 DRDRAM with considerably lower latency. To achieve RDRAM's 800 MHz clock rate, the memory module runs on a 16-bit bus instead of a 64-bit bus in contemporary SDRAM DIMM. At the time of the Intel 820 launch some RDRAM modules operated at rates less than 800 MHz.
Benchmarks Benchmark tests conducted in 1998 and 1999 showed most everyday applications to run minimally slower with RDRAM. In 1999, benchmarks comparing the Intel 840 and Intel 820 RDRAM chipsets with the
Intel 440BX SDRAM chipset led to the conclusion that the performance gain of RDRAM did not justify its cost over SDRAM, except for use in workstations. In 2001, benchmarks pointed out that single-channel DDR266 SDRAM modules could closely match dual-channel 800 MHz RDRAM in everyday applications.
Marketing history In November 1996, Rambus entered into a development and license contract with Intel. Intel announced that it would only support the Rambus memory interface for its
microprocessors and had been granted rights to purchase one million shares of Rambus' stock at $10 per share. As a transition strategy, Intel planned to support PC-100 SDRAM DIMMs on future Intel 82x chipsets using Memory Translation Hub (MTH). In 2000, Intel recalled the Intel 820 motherboard, which featured the MTH, due to occasional occurrences of
hanging and spontaneous reboots caused by
simultaneous switching noise. Since then, no production Intel 820 motherboards contain MTH. In 2000, Intel began to subsidize RDRAM by bundling retail boxes of
Pentium 4s with two RIMMs. Intel began to phase out these subsidies in 2001. In 2003, Intel introduced the 865 and 875 chipsets with dual-channel DDR SDRAM support, which were marketed as high-end replacements of the 850 chipset. Furthermore, the future memory roadmap did not include RDRAM. == Other uses ==