Registered jack

The registered jack designations originated in the standardization process of telephone connections in the Bell System in the United States, and describe application circuits and not just the physical geometry of the connectors. The same modular connector type may be used for different registered jack applications. Modular connectors were developed to replace older telephone installation methods that used hardwired cords or bulkier varieties of telephone plugs. Strictly, Registered Jack refers to both the female physical connector (modular connector) and specific wiring patterns, but the term is often used loosely to refer to modular connectors regardless of wiring, gender, or use, commonly for telephone line connections, but also for Ethernet over twisted pair, resulting in confusion over the various connection standards and applications. For example, the six-position physical connector, plug and jack, is identically dimensioned and inter-connectable, whether it is wired for one, two, or three lines. These are the RJ11, RJ14, and RJ25 interfaces. The RJ standards designations only pertain to the wiring of the (female) jacks, hence the name Registered Jack. It is commonplace, but not strictly correct, to refer to the unwired connectors or the (male) plugs by these names. The nomenclature for modular connectors is based on the number of contact positions and the number of contacts present. 6P indicates a six-position modular plug or jack. A six-position modular plug with conductors in only the middle two positions is designated 6P2C; 6P4C has four conductors in the middle positions, and 6P6C has all six. An RJ11 without power, if made with a 6P6C connector, has four unused contacts. ==History and authority==

Registration interfaces were created by the Bell System under a Federal Communications Commission order for the standard interconnection between telephone company equipment and customer premises equipment. These interfaces used newly standardized jacks and plugs, primarily based on miniature modular connectors. The wired communications provider (telephone company) is responsible for delivery of services to a minimum (or main) point of entry (MPOE). The MPOE is a utility box, usually containing surge protective circuitry, which connects the wiring on the customer's property to the communication provider's network. Customers are responsible for all jacks, wiring, and equipment on their side of the MPOE. The intent was to establish a universal standard for wiring and interfaces, and to separate ownership of in-home (or in-office) telephone wiring from the wiring owned by the service provider. In the Bell System, following the Communications Act of 1934, the telephone companies owned all telecommunications equipment and they did not allow interconnection of third-party equipment. Telephones were generally hardwired, but may have been installed with Bell System connectors to permit portability. The legal case Hush-A-Phone v. United States (1956) and the Federal Communications Commission's (FCC) Carterfone (1968) decision brought changes to this policy, and required the Bell System to allow some interconnection, culminating in the development of registered interfaces using new types of miniature connectors. Registered jacks replaced the use of protective couplers provided exclusively by the telephone company. The new modular connectors were much smaller and cheaper to produce than the earlier, bulkier connectors that were used in the Bell System since the 1930s. The Bell System issued specifications for the modular connectors and their wiring as Universal Service Order Codes (USOC), which were the only standards at the time. Large customers of telephone services commonly use the USOC to specify the interconnection type and, when necessary, pin assignments, when placing service orders with a network provider. When the U.S. telephone industry was reformed to foster competition in the 1980s, the connection specifications became federal law, ordered by the FCC and codified in the Code of Federal Regulations (CFR), Title 47 CFR Part 68, Subpart F, superseded by T1.TR5-1999. For this delegation, the FCC removed Subpart F from the CFR and added Subpart G. The ACTA derives its recommendations for terminal attachments from the standards published by the engineering committees of the Telecommunications Industry Association (TIA). ACTA and TIA jointly published the standard TIA/EIA-IS-968, replacing the CFR information. TIA-968-A, the current version of that standard, by reference. With the publication of TIA-968-B, the connector descriptions have been moved to TIA-1096-A. A registered jack name, such as RJ11, still identifies both the physical connectors and the wiring (pinout) for each application. ==Types==

The most widely implemented registered jack in telecommunications is the RJ11. This is a modular connector wired for one telephone line, using the center two contacts of six available positions. This configuration is also used for single-line telephones in many countries other than the United States. It may also use a 6P4C connector, to use an additional wire pair for powering lamps on the telephone set. RJ14 is similar to RJ11, but is wired for two lines and RJ25 has three lines. RJ61 is a similar registered jack for four lines, but uses an 8P8C connector. The RJ45S jack is rarely used in telephone applications, and the keyed 8P8C modular plug used for RJ45S mechanically cannot be inserted into an Ethernet port, but a similar plug, the non-keyed 8P8C modular plugnever used for RJ45Sis used in Ethernet networks, and the connector is often, however improperly, referred to as RJ45 in this context. Many of the basic names have suffixes that indicate subtypes: • C: flush-mount or surface mount • F: flex-mount • W: wall-mount • L: lamp-mount • S: single-line • M: multi-line • X: complex jack For example, RJ11 comes in two forms: RJ11W is a jack from which a wall telephone can be hung, while RJ11C is a jack designed to have a cord plugged into it. A cord can be plugged into an RJ11W as well. ==RJ11, RJ14, RJ25 wiring==

All of these registered jacks are described as containing a number of potential contact positions and the actual number of contacts installed within these positions. RJ11, RJ14, and RJ25 all use the same six-position modular connector, thus are physically identical except for the different number of contacts (two, four and six respectively) allowing connections for one, two, or three telephone lines respectively. A cord connecting to an RJ11 interface requires a 6P2C connector. Nevertheless, cords sold as RJ11 often use 6P4C connectors (six position, four conductor) with four wires. Two of the six possible contact positions connect tip and ring, and the other two conductors are unused. The conductors other than the two central tip and ring conductors are in practice variously used for a second or third telephone line, a ground for selective ringers, low-voltage power for a dial light, or for anti-tinkle circuitry to prevent pulse-dialing phones from sounding the bell on other extensions. Pinout The pins of the 6P6C connector are numbered 1 to 6, counting left to right when holding the cord entrance facing the viewer with the connector tab down. Provisioning of power Some telephones such as the Western Electric Princess and Trimline telephone models require additional power (~6 V AC) for operation of the incandescent dial light. This power is delivered to the telephone set from a transformer by the second wire pair (pins 2 and 5) of the 6P4C connector. ==RJ21==

RJ21 is a registered jack standard using a micro ribbon connector with contacts for up to fifty conductors. It is used to implement connections for up to 25 lines, or circuits that require many wire pairs, such as used in the 1A2 key telephone system. The miniature ribbon connector of this interface is also known as a 50-pin telco connector, CHAMP(AMP), or Amphenol connector, the last being a genericized trademark, as Amphenol was a prominent manufacturer of these at one time. A cable color scheme, known as even-count color code, is determined for 25 pairs of conductors as follows: For each ring, the primary, more prominent color is chosen from the set blue, orange, green, brown, and slate, in that order, and the secondary, thinner stripe color from the set of white, red, black, yellow, and violet colors, in that order. The tip conductor color scheme uses the same colors as the matching ring but switches the thickness of the primary and secondary colored stripes. Since the sets are ordered, an orange (color 2 in its set) with a yellow (color 4) is the color scheme for the 4·5 + 2 − 5 = 17th pair of wires. If the yellow is the more prominent, thicker stripe, then the wire is a tip conductor connecting to the pin numbered 25 + the pair #, which is pin 42 in this case. Ring conductors connect to the same pin number as the pair number. A conventional enumeration of wire color pairs then begins blue (and white), orange (and white), green (and white) and brown (and white), which subsumes a color-coding convention used in cables of 4 or fewer pairs (8 wires or less) with 8P and 6P connectors. Dual 50-pin ribbon connectors are often used on punch blocks to create a breakout box for private branch exchange (PBX) and other key telephone systems. ==RJ45S==

The RJ45S, an obsolete standard{{cite web |url=https://www.lifewire.com/definition-of-rj45-817872 |title=The Basics of RJ45, RJ45s, and 8P8C, Connectors and Cables ==RJ48==

RJ48 is used for T1 and ISDN termination, local-area data channels, and subrate digital services. It uses the eight-position modular connector (8P8C). RJ48C is commonly used for T1 circuits and uses pin numbers 1, 2, 4 and 5. RJ48X is a variation that contains shorting blocks in the jack for troubleshooting: With no plug inserted, pins 2 and 5 (the two tip wires) are connected to each other, and likewise 1 and 4 (ring), creating a loopback so that a signal received on one pair is returned on the other. Sometimes this is referred to as a self-looping jack. RJ48S is typically used for local-area data channels and subrate digital services and carries one line. It accepts a keyed variety of the 8P modular connector. RJ48 connectors are fastened to shielded twisted pair (STP) cables, not the unshielded twisted-pair (UTP) commonly used in other installations. ==RJ61==

RJ61 is a physical interface that was often used for terminating twisted pair cables. It uses an eight-position, eight-conductor (8P8C) modular connector. This wiring pattern is for multi-line analog telephone use only; RJ61 is unsuitable for use with high-speed data because the pins for pairs 3 and 4 are too widely spaced for high signaling frequencies. T1 lines use another wiring for the same connector, designated RJ48. Ethernet over twisted pair (10BASE-T, 100BASE-TX and 1000BASE-T) also uses different wiring for the same connector, either T568A or T568B. RJ48, T568A, and T568B are all designed to keep both wires of each pair close together. The flat eight-conductor silver-satin cable conventionally used with four-line analog telephones and RJ61 jacks is also unsuitable for use with high-speed data. Twisted pair cabling is required for data applications. Twisted-pair patch cable typically used with common Ethernet and other data network standards is not compatible with RJ61, because RJ61 pairs 3 and 4 would each be split across two different twisted pairs in the patch cable, causing excessive cross-talk between voice lines 3 and 4, with conversations on each line literally being audible on the other. With the advent of structured wiring systems and TIA/EIA-568 (now ANSI/TIA-568) conventions, the RJ61 wiring pattern is falling into disuse. The T568A and T568B standards are used in place of RJ61 so that a single wiring standard in a facility can be used for both voice and data. ==Similar jacks and unofficial names==

The following RJ-style names do not refer to official ACTA types. The labels RJ9, RJ10, RJ22 are variously used for 4P4C and 4P2C modular connectors, most typically installed on telephone handsets and their cordage. Telephone handsets do not connect directly to the public network, and therefore have no registered jack designation. RJ11 generally uses 6P2C, but can also be 6P4C if powered. RJ45 is often incorrectly used when referring to an 8P8C connector used for ANSI/TIA-568 T568A and T568B and Ethernet. The connector commonly used for twisted-pair Ethernet is a non-keyed 8P8C connector, quite distinct from that used for RJ45S. The plug used for RJ45S is both mechanically and electrically incompatible with any Ethernet port: it cannot fit into an Ethernet port, and it is wired in a way that is incompatible with Ethernet. The new ARJ45 interface, however, is a plug and jack allowing higher transmission rates, and the jack can, optionally, be backward-compatible with the common 8P8C plugs of Gigabit Ethernet and earlier standards. RJ50 is often a 10P10C interface, often used for data applications. The micro ribbon connector, first made by Amphenol, that is used in the RJ21 interface, has also been used to connect Ethernet ports in bulk from a switch with 50-pin ports to a Cat-5 rated patch panel, or between two patch panels. A cable with a 50-pin connector on one end can support six fully wired 8P8C connectors or Ethernet ports on a patch panel with one spare pair. Alternatively, only the necessary pairs for 10/100 Ethernet can be wired allowing twelve Ethernet ports with a single spare pair. This connector is also used with spring bail locks for SCSI-1 connections. Some computer printers use a shorter 36-pin version known as a Centronics connector. The 8P8C modular jack was chosen as a candidate for ISDN systems. In order to be considered, the connector system had to be defined by an international standard, leading to the creation of the ISO 8877 standard. Under the rules of the IEEE 802 standards project, international standards are to be preferred over national standards, so when the original 10BASE-T twisted-pair wiring version of Ethernet was developed, this modular connector was chosen as the basis for IEEE 802.3i-1990. ==See also==