S-100 bus

The bus is a passive backplane of 100-pin printed circuit board edge connectors wired in parallel. Circuit cards measuring serving the functions of CPU, memory, or I/O interface plugged into these connectors. The bus signal definitions closely follow those of an 8080 microprocessor system, since the Intel 8080 microprocessor was the first microprocessor hosted on the bus. The 100 lines of the bus can be grouped into four types: 1) Power, 2) Data, 3) Address, and 4) Clock and control. Power supplied on the bus is bulk unregulated +8 Volt DC and ±16 Volt DC, designed to be regulated on the cards to +5 V (used by TTL ICs), -5 V and +12 V for the Intel 8080 CPU IC, ±12 V RS-232 line driver ICs, +12 V for disk drive motors. The onboard voltage regulation is typically performed by devices of the 78xx family (for example, a 7805 device to produce +5 volts). These linear regulators would commonly be mounted on heat sinks. The bi-directional 8-bit data bus of the Intel 8080 is split into two unidirectional 8-bit data buses. The processor could use only one of these at a time. The Sol-20 used a variation that had only a single 8-bit bus and used the now-unused pins as signal grounds to reduce electronic noise. The direction of the bus, in or out, was signaled using the otherwise unused DBIN pin. This became universal in the market as well, making the second bus superfluous. Later, these two 8-bit buses would be combined to support a 16-bit data width for more advanced processors, using the Sol's system to signal the direction. The address bus was 16-bits wide in the initial implementation and later extended to 24-bits wide. A bus control signal can put these lines in a tri-state condition to allow direct memory access. The Cromemco Dazzler, for example, is an early card that retrieved digital images from memory using direct memory access. Clock and control signals are used to manage the traffic on the bus. For example, the DO Disable line will tristate the address lines during direct memory access. Unassigned lines of the original bus specification were later assigned to support more advanced processors. For example, the Zilog Z-80 processor has a non-maskable interrupt line that the Intel 8080 processor does not. One unassigned line of the bus then was reassigned to support the non-maskable interrupt request. ==History==

During the design of the Altair, the hardware required to make a usable machine was not available in time for the January 1975 launch date. The designer, Ed Roberts, also had the problem of the backplane taking up too much room. Attempting to avoid these problems, he placed the existing components in a case with additional "slots", so that the missing components could be plugged in later when they became available. The backplane is split into four separate cards, with the CPU on a fifth. He then looked for an inexpensive source of connectors, and he came across a supply of military surplus 100-pin edge connectors. The 100-pin bus was created by an unknown draftsman at MITS, who selected the connector from a parts catalog and arbitrarily assigned signal names to groups of connector pins. A burgeoning industry of "clone" machines followed the introduction of the Altair in 1975. Most of these used the same bus layout as the Altair, creating a new industry standard. These companies were forced to refer to the system as the "Altair bus", and wanted another name in order to avoid referring to their competitor when describing their own system. The "" name, short for "Standard 100", was coined by Harry Garland and Roger Melen, co-founders of Cromemco. While on a flight to attend the Atlantic City PC '76 microcomputer conference in August 1976, they shared the cabin with Bob Marsh and Lee Felsenstein of Processor Technology. Melen went over to them to convince them to adopt the same name. He had a beer in his hand and when the plane hit a bump, Melen spilt some of the beer on Marsh. Marsh agreed to use the name, which Melen ascribes to him wanting to get Melen to leave with his beer. The term first appeared in print in a Cromemco advertisement in the November 1976 issue of Byte magazine. The first symposium on the bus, moderated by Jim Warren, was held November 20, 1976 at Diablo Valley College with a panel consisting of Harry Garland, George Morrow, and Lee Felsenstein. Just one year later, the Bus would be described as "the most used busing standard ever developed in the computer industry." Cromemco was the largest of the manufacturers, followed by Vector Graphic and North Star Computers. Other innovators were companies such as Alpha Microsystems, IMS Associates, Inc., Godbout Electronics (later CompuPro), and Ithaca InterSystems. In May 1984, Microsystems published a comprehensive product directory listing over 500 "/IEEE-696" products from over 150 companies. The bus signals were simple to create using an 8080 CPU, but increasingly less so when using other processors like the 68000. More board space was occupied by signal conversion logic. Nonetheless by 1984, eleven different processors were hosted on the bus, from the 8-bit Intel 8080 to the 16-bit Zilog Z-8000. == IEEE-696 Standard ==

As the bus gained momentum, there was a need to develop a formal specification of the bus to help assure compatibility of products produced by different manufacturers. There was also a need to extend the bus so that it could support processors more capable than the Intel 8080 used in the original Altair Computer. In May 1978, George Morrow and Howard Fullmer published a "Proposed Standard for the Bus" noting that 150 vendors were already supplying products for the Bus. This proposed standard documented the 8-bit data path and 16-bit address path of the bus and stated that consideration was being given to extending the data path to 16 bits and the address path to 24 bits. In this specification the data path was extended to 16 bits and the address path was extended to 24 bits. The IEEE 696 Working Group, chaired by Mark Garetz, continued to develop the specification which was proposed as an IEEE Standard and approved by the IEEE Computer Society on June 10, 1982.{{cite book| title=An American National Standard: IEEE 696 Standard Interface Devices The American National Standards Institute (ANSI) approved the IEEE standard on September 8, 1983. The computer bus structure developed by Ed Roberts for the Altair 8800 computer had been extended, rigorously documented, and now designated as the American National Standard IEEE Std 696–1983. == Retirement ==

Systems at the Chicago Mercantile Exchange in 1984 IBM introduced the IBM Personal Computer in 1981 and followed it with increasingly capable models: the XT in 1983 and the AT in 1984. The success of these computers, which used IBM's own, incompatible bus architecture, cut deeply into the market for bus products. In May 1984, Sol Libes (who had been a member of the IEEE-696 Working Group) wrote in Microsystems: "there is no doubt that the S-100 market can now be considered a mature industry with only moderate growth potential, compared to the IBM PC-compatible market". As the IBM PC products captured the low-end of the market, machines moved up-scale to more powerful OEM and multiuser systems. Banks of bus computers were used, for example, to process the trades at the Chicago Mercantile Exchange; the United States Air Force deployed bus machines for their mission planning systems. However throughout the 1980s the market for bus machines for the hobbyist, for personal use, and even for small business was on the decline. The market for bus products continued to contract through the early 1990s, as IBM-compatible computers became more capable. In 1992, the Chicago Mercantile Exchange, for example, replaced their bus computers with the IBM model PS/2. By 1994, the bus industry had contracted sufficiently that the IEEE did not see a need to continue supporting the IEEE-696 standard. The IEEE-696 standard was retired on June 14, 1994. ==References==