Fastening Originally, the mounting holes were
tapped with a particular screw thread. When
rack rails are too thin to tap,
rivet nuts or other
threaded inserts can be used, and when the particular class of equipment to be mounted is known in advance, some of the holes can be omitted from the mounting rails. Threaded mounting holes in racks where the equipment is frequently changed are problematic because the threads can be damaged or the mounting screws can break off; both problems render the mounting hole unusable. Tapping large numbers of holes that may never be used is expensive; nonetheless, tapped-hole racks are still in use, generally for hardware that rarely changes. Examples include telephone exchanges, network cabling panels, broadcast studios and some government and military applications. The tapped-hole rack was first replaced by clearance-hole (Round Hole, Round Unthreaded Holes, and Versa Rail) racks. The holes are large enough to permit a bolt to be freely inserted through without binding, and bolts are fastened in place using
cage nuts. In the event of a nut being stripped out or a bolt breaking, the nut can be easily removed and replaced with a new one. Production of clearance-hole racks is less expensive. The next innovation in rack design has been the square-hole rack. Square-hole racks allow boltless mounting, such that the rack-mount equipment only needs to insert through and hook down into the lip of the square hole. Installation and removal of hardware in a square-hole rack is very easy and boltless, where the weight of the equipment and small retention clips are all that is necessary to hold the equipment in place. Older equipment meant for round-hole or tapped-hole racks can still be used, with the use of cage nuts made for square-hole racks.
Structural support Rack-mountable equipment is traditionally mounted by bolting or clipping its front panel to the rack. Within the IT industry, it is common for network/communications equipment to have multiple mounting positions, including tabletop and wall mounting, so rack-mountable equipment will often feature L-brackets that must be screwed or bolted to the equipment prior to mounting in a 19-inch rack. With the prevalence of
23-inch racks in the Telecoms industry, the same practice is also common, but with equipment having 19-inch and 23-inch brackets available, enabling them to be mounted in existing racks. A key structural weakness of front-mounted support is the bending stress placed on the mounting brackets of the equipment and the rack itself. As a result, 4-post racks have become common, featuring a mirrored pair of rear mounting posts. Since the spacing between the front and rear mounting posts may differ between rack vendors and/or the configuration of the rack (some racks may incorporate front and rear rails that may be moved forward and backward, e.g., APC SX-range racks), it is common for equipment that features 4-post mounting brackets to have an adjustable rear bracket. Servers and deep pieces of equipment are often mounted using rails that are bolted to the front and rear posts (as above, it is common for such rails to have an adjustable depth), allowing the equipment to be supported by four posts, while also enabling it to be easily installed and removed. Although there is no standard for the depth of equipment, nor specifying the outer width and depth of the rack enclosure itself (incorporating the structure, doors and panels that contain the mounting rails), there is a tendency for 4-post racks to be or wide, and for them to be , or deep. This, of course, varies by manufacturer, the design of the rack and its purpose, but through common constraining factors (such as raised-floor tile dimensions), these dimensions have become quite common. The extra width and depth enable cabling to be routed with ease (also helping to maintain the minimum bend radius for fiber and copper cables) and deeper equipment to be utilized. A common feature in IT racks is mounting positions for
zero-U accessories, such as
power distribution units (PDUs) and vertical cable managers and ducts, that utilize the space between the rear rails and the side of the rack enclosure. The strength required of the mounting posts means they are invariably not merely flat strips but actually a wider folded strip arranged around the corner of the rack. The posts are usually made of
steel of around 2 mm thickness (the official standard recommends a minimum of 1.9 mm), or of slightly thicker
aluminum. Racks, especially two-post racks, are often secured to the floor or adjacent building structure so as not to fall over. This is usually required by local building codes in
seismic zones. According to
Telcordia Technologies Generic Requirements document GR-63-CORE, during an earthquake, telecommunications equipment is subjected to motions that can over-stress the equipment framework, circuit boards, and connectors. The amount of motion and resulting stress depends on the structural characteristics of the building and framework in which the equipment is contained and the severity of the earthquake. Seismic racks rated according to GR-63,
NEBS Requirements: Physical Protection, are available, with Zone 4 representing the most demanding environment. GR-3108,
Generic Requirements for Network Equipment in the Outside Plant (OSP), specifies the usable opening of seismic-compliant 19-inch racks.
Rails (slides) Heavy equipment or equipment that is commonly accessed for servicing, for which attaching or detaching at all four corners simultaneously would pose a problem, is often not mounted directly onto the rack but instead is mounted via rails (or slides). A pair of rails is mounted directly onto the rack, and the equipment then slides into the rack along the rails, which support it. When in place, the equipment may also then be bolted to the rack. The rails may also be able to fully support the equipment in a position where it has been slid clear of the rack; this is useful for inspection or maintenance of equipment, which will then be slid back into the rack. Some rack slides even include a tilt mechanism allowing easy access to the top or bottom of rack-mounted equipment when it is fully extended from the rack. Slides or rails for computers and other data processing equipment, such as
disk arrays or
routers, often need to be purchased directly from the equipment manufacturer, as there is no standardization on such equipment's thickness (measurement from the side of the rack to the equipment) or means for mounting to the rail. A rails kit may include a cable management arm (CMA), which folds the cables attached to the server and allows them to expand neatly when the server is slid out, without being disconnected.
Computer mounting Computer servers designed for rack-mounting can include a number of extra features to make the server easy to use in the rack: • The sliding rails can lock in various extended positions to prevent the equipment from moving when extended out from the rack for service. • The server itself might have locking pins on the sides that just drop into slots on the extended rail assembly, in a manner similar to a removable kitchen drawer. This permits very easy server installation and removal since there is no need for the server to be held in midair while someone fastens each rail to the sides of the server with screws. • Some manufacturers of rack-mount hardware include a folding cable tray behind the server, so that the cables are held in a neat and tidy folded channel when inside the rack, but can unfold out into a long strip when pulled out of the rack, allowing the server to continue to be plugged in and operating normally even while fully extended and hanging in mid-air in front of the rack. This piece of equipment thus simplifies maintenance, but at the cost of providing a restriction to airflow. • Rack-optimized servers might duplicate indicator lights on the front and rear of the rack to help identify a machine needing attention or provide separate
identify LED indicators on both sides of the server (which can be turned on in software or by pushing an associated button). Since some configurations permit over fifty 1U servers in a single rack, this provides a simple method to determine exactly which machine is having a problem when at the rear of the rack. • A handle may be provided at the rear of the server rails to help pull or push the server without having to pull on the cables. When there is a large number of computers in a single rack, it is impractical for each one to have its own separate keyboard, mouse, and monitor. Instead, a
KVM switch or
LOM software is used to share a single keyboard/video/mouse set amongst many different computers. Since the mounting hole arrangement is vertically symmetric, it is possible to mount rack-mountable equipment upside-down. However, not all equipment is suitable for this type of mounting. For instance, most
optical disc players will not work upside-down because the driving
motor mechanism does not grip the disc.
Rack types A standard 19-inch server rack cabinet is typically 42u in height, wide, and deep. Most data centers use four-post racks.
Two-post relay racks Two-post racks provide two vertical posts. These posts are typically heavy-gauge metal or extruded aluminum. A top bar and wide foot connect the posts and allow the rack to be securely attached to the floor and/or roof for seismic safety. Equipment can be mounted either close to its center of gravity (to minimize load on its front panel), or via the equipment's front panel holes. Rack strips used for road cases come in 2 types: single angle and double angle. Double-angle rack strips offer better structural strength and an additional mounting face for cable management or additional support for heavy equipment.
Fiberglass-reinforced plastic case racks In 1965, a durable
fiber-reinforced plastic 19-inch rackmount case was patented by ECS Composites and became widely used in military and commercial applications for electronic deployment and operation. Rackmount cases are also constructed of thermo-stamped composite,
carbon fiber, and
DuPont's
Kevlar for military and commercial uses.
Polyethylene molded case racks Portable rack cases using a rotary-molded
polyethylene outer shell are a lower-cost alternative to the more durable ATA-approved case. These cases are marketed to musicians and entertainers for equipment not subject to frequent transportation and rough handling. The polyethylene shell is not fiberglass reinforced and is not rigid. The shape of small cases is maintained by the rack rails and the cover seal extrusions alone. Larger cases are further reinforced with additional plywood or sheet metal. The outer shell is frequently embossed in a self-mating pattern to combat the tendency for stacked cases to deform slightly, creating a slope that encourages the upper case to slide off. The cases typically use extruded aluminum bands at the ends of the body with tongue-and-groove mating to like bands for the covers. End covers are typically secured with either a simple draw latch or a rotary cam
butterfly latch, named for the shape of the twist handle. ==Cooling==