Basic requirements This section focuses on T-TRAK standards, one of a number of
N scale modular standards as outlined in the N Scale Module Standards document. Basic T-TRAK module requirements are very simple; there are few "formal" specifications for a T-TRAK module. Since almost all modules are built to the N specifications, so reference to T-TRAK is understood to be N scale. Other scales include the scale reference, such as T-TRAK-Z. Let us start with some definitions. The "length or width" of the module is the axis parallel to the track. The terms length and width are used interchangeably in T-TRAK. The "depth" of the module is the dimension perpendicular to the track and is the distance from the front (nearest the track) of the module to the back. The "height" of the module is measured from the bottom of the module to the base of the track. The first item in the list of formal T-TRAK specifications is that the track at the module edges must be Kato Unitrack. Modules in a layout are not clamped or bolted together in any fashion. The only thing that holds the modules together in a layout are the Kato uni-joiners. It is acceptable to use track from other manufacturers between the Kato Unitrack interfaces, however, most T-TRAK builders use Kato Unitrack exclusively on their T-TRAK modules. Builders must ensure the trackwork on their modules will not cause issues while running trains. The first time T-TRAK builder is advised to use Kato Unitrack exclusively on their first few modules. The use of Kato track created an early "informal" standard for the length of track on a module to be 310 mm (which is ). A module of this size is typically referred to as a "single". A module with 620 mm of track is referred to as a "double". Those with 930 mm of track are known as "triples" and, there are "quads" and even longer T-TRAK modules for special situations. It is advisable that all track on straight modules be built as a multiple of 310 mm units of track for reasons of compatibility. The reason this is advised is because most T-TRAK layouts consist of a double row of modules on a table and a non-standard length module on one side will not permit the loop to be closed. In order for a non-standard length module to be used, another module of equal length must be built and used on the other side of the table, or the layout must be constructed as a single row of modules with return loops on each end. While a non-standard length T-TRAK module can be constructed, the builder should recognize that doing so may limit the usability of that module in a multi-person, multi-club layout. Kato produces straight track in increments of 62 mm. (i.e. 62 mm, 124 mm, 186 mm, 248 mm and the double crossover is 310 mm) and straight track is packaged four pieces to the package so for most typical track combinations (e.g. ; ) two packages of track are enough for two single modules or one double module. There are other combinations that create 310 mm of track but they will require more pieces. Since Kato track is measured in metric units it is easiest to build modules using metric measurements. There are multiple ways to build a T-TRAK module but the most common is the box method. This is basically a lidless, inverted box. For a module of single length (i.e. 310 mm of track), the box should be no more than wide. This gap provides for 1 mm of track overhang on each side of the module. This 1 mm overhang (or more) is part of the formal T-TRAK standards. It was implemented to allow flexibility with connecting to other modules that may not be built squarely, or for those that warped or flexed. The formal standard height of the module is and is adjustable to a height of by utilizing leveling bolts. The height measurement is from a flat surface to the base of the Kato track. There is no
formal specification for the depth of a module. The original T-TRAK modules and subsequent kits from Lee Monaco-Fitzgerald were deep. However, the depth for modules varied by builder depending on the desire for scenery space and available building materials. The general practice building T-TRAK modules is that they should be no deeper than . In a typical double row, oval layout this permits a small gap between the backs of modules. Since this is an informal maximum there is some flexibility with this dimension. For example, a smaller module could be built and placed opposite a deeper module, however, this arrangement could limit the use of those modules in some layouts. The recommended offset from the front fascia to the edge of the ballast (not track center) of the front track, or outer line, is . The center to center spacing for the second, or inner line can either be 25 mm or 33 mm. The 25 mm spacing was the original specification for T-TRAK but is rarely used due to clearance issues on corners with longer rolling stock. Track spacing of 33 mm is the most common spacing for existing modules and is identical to Kato's double track pieces (e.g. concrete tie track, double crossover, etc.). Regardless of the track spacing, it is imperative that both front and back tracks are even and square with respect to each other and the box upon which they are affixed. It is a
best practice to use Kato's double track sections as alignment tools when affixing track to a module.
Electrical standards One of the most discussed T-TRAK standards is the wiring standard. The wiring specification is a formal standard. For modules wired for track power and using standard Kato connectors, the specification is that the rails, beginning with the front rail on the front track, be wired in a Blue, White, White, Blue order. This is also known as "blue to the outside". At the time, this was considered to be a benefit because it permitted running a train on each loop (inner and outer) in opposite directions with one DC throttle. Regardless of the historical reasoning, the standard has been in place since the beginning and has not changed. The proper way to reverse the polarity for the inner line is to do so at the power pack and not at the module. All modules that feature a power drop should be wired to the specification and have the Kato power connectors. It is a best practice to have a power drop every six to eight single modules (approximately every 2 meters, or 6–8 feet) around a layout. The Kato wiring accessories (e.g. Unitrack DC Extension cord, Unitrack 3-Way Extension Cord) are sufficient to power layouts that are three tables in length. For very large layouts, there is an updated standard of using a wiring bus similar to that which was developed by the T-TRAK Division of the North Virginia NTRAK club. The details are covered in the formal T-TRAK Standards document. == External links ==