Tensile testing

Tensile testing might have a variety of purposes, such as: • Select a material or item for an application • To understand state of degradation of cultural heritage (heritage science) and choose appropriate materials for conservation treatment. • Predict how a material will perform in use: normal and extreme forces. • Determine if, or verify that, the requirements of a specification, regulation, or contract are met • Decide if a new product development program is on track • Demonstrate proof of concept • Demonstrate the utility of a proposed patent • Provide standard data for other scientific, engineering, and quality assurance functions • Provide a basis for Technical communication • Provide a technical means of comparison of several options • Provide evidence in legal proceedings ==Tensile specimen==

The preparation of test specimens depends on the purposes of testing and on the governing test method or specification. A tensile specimen usually has a standardized sample cross-section. It has two shoulders and a gauge (section) in between. The shoulders and grip section are generally larger than the gauge section by 33% so they can be easily gripped. The gauge section's smaller diameter also allows the deformation and failure to occur in this area. The shoulders of the test specimen can be manufactured in various ways to mate to various grips in the testing machine (see the image below). Each system has advantages and disadvantages; for example, shoulders designed for serrated grips are easy and cheap to manufacture, but the alignment of the specimen is dependent on the skill of the technician. On the other hand, a pinned grip assures good alignment. Threaded shoulders and grips also assure good alignment, but the technician must know to thread each shoulder into the grip at least one diameter's length, otherwise the threads can strip before the specimen fractures. For workpieces that are machined from bar stock, the test specimen can be made from the same piece as the bar stock. For soft and porous materials, like electrospun nonwovens made of nanofibers, the specimen is usually a sample strip supported by a paper frame to favour its mounting on the machine and to avoid membrane damaging. The repeatability of a testing machine can be found by using special test specimens meticulously made to be as similar as possible. A standard specimen is prepared in a round or a square section along the gauge length, depending on the standard used. Both ends of the specimens should have sufficient length and a surface condition such that they are firmly gripped during testing. The initial gauge length Lo is standardized (in several countries) and varies with the diameter (Do) or the cross-sectional area (Ao) of the specimen as listed The following tables gives examples of test specimen dimensions and tolerances per standard ASTM E8. ==Equipment==

The most common testing machine used in tensile testing is the universal testing machine. This type of machine has two crossheads; one is adjusted for the length of the specimen and the other is driven to apply tension to the test specimen. Testing machines are either electromechanical or hydraulic. The electromechanical machine uses an electric motor, gear reduction system and one, two or four screws to move the crosshead up or down. A range of crosshead speeds can be achieved by changing the speed of the motor. The speed of the crosshead, and consequently the load rate, can be controlled by a microprocessor in the closed-loop servo controller. A hydraulic testing machine uses either a single- or dual-acting piston to move the crosshead up or down. Manually operated testing systems are also available. Manual configurations require the operator to adjust a needle valve in order to control the load rate. A general comparison shows that the electromechanical machine is capable of a wide range of test speeds and long crosshead displacements, whereas the hydraulic machine is a cost-effective solution for generating high forces. The machine must have the proper capabilities for the test specimen being tested. There are four main parameters: force capacity, speed, precision and accuracy. Force capacity refers to the fact that the machine must be able to generate enough force to fracture the specimen. The machine must be able to apply the force quickly or slowly enough to properly mimic the actual application. Finally, the machine must be able to accurately and precisely measure the gauge length and forces applied; for instance, a large machine that is designed to measure long elongations may not work with a brittle material that experiences short elongations prior to fracturing. Alignment of the test specimen in the testing machine is critical, because if the specimen is misaligned, either at an angle or offset to one side, the machine will exert a bending force on the specimen. This is especially bad for brittle materials, because it will dramatically skew the results. This situation can be minimized by using spherical seats or U-joints between the grips and the test machine. The strain measurements are most commonly measured with an extensometer, but strain gauges are also frequently used on small test specimen or when Poisson's ratio is being measured. Newer test machines have digital time, force, and elongation measurement systems consisting of electronic sensors connected to a data collection device (often a computer) and software to manipulate and output the data. However, analog machines continue to meet and exceed ASTM, NIST, and ASM metal tensile testing accuracy requirements, continuing to be used today. ==Process==

The test process involves placing the test specimen in the testing machine and slowly extending it until it fractures. During this process, the elongation of the gauge section is recorded against the applied force. The data is manipulated so that it is not specific to the geometry of the test sample. The elongation measurement is used to calculate the engineering strain, ε, using the following equation: == Tensile testing creep ==

Tensile testing can be used to test creep in materials, a slow plastic deformation of the material from constant applied stresses over extended periods of time. Creep is generally aided by diffusion and dislocation movement. While there are many ways to test creep, tensile testing is useful for materials such as concrete and ceramics that behave differently in tension and compression, and thus possess different tensile and compressive creep rates. As such, understanding the tensile creep is important in the design of concrete for structures that experience tension, such as water holding containers, or for general structural integrity. Tensile testing of creep generally follows the same testing process as standard testing albeit generally at lower stresses to remain in the creep domain rather than plastic deformation. Additionally, specialized tensile creep testing equipment may include incorporated high temperature furnace components to aid diffusion. The sample is held at constant temperature and tension, and strain on the material is measured using strain gauges or laser gauges. The measured strain can be fitted with equations governing different mechanisms of creep, such as power law creep or diffusion creep (see creep for more information). Further analysis can be obtained from examining the sample post fracture. Understanding the creep mechanism and rate be able to aid materials selection and design. It is important to note that sample alignment is important for tensile testing creep. Off centered loading will result in a bending stress being applied to the sample. Bending can be measured by tracking strain on all sides of the sample. The percent bending can then be defined as the difference between strain on one face (\varepsilon_1) and the average strain (\varepsilon_0): \text{Percent Bending} = \frac{\varepsilon_1 - \varepsilon_0}{\varepsilon_0} \times 100 Percent bending should be under 1% on the wider face of loaded samples, and under 2% on the thinner face. Bending can be caused by misalignment on the loading clamp and asymmetric machining of samples. ==Standards==

Metals • ASTM E8/E8M-24: Standard Test Methods for Tension Testing of Metallic Materials • ISO 6892-1: Metallic materials − Tensile testing − Part 1: Method of test at room temperature • ISO 6892-2: Metallic materials − Tensile testing − Part 2: Method of test at elevated temperature • JIS Z 2241: Metallic materials − Tensile testing − Method of test at room temperature • MPIF Standard Test Standard 10: Method for Determination of the Tensile Properties of Powder Metallurgy (PM) Materials Composites • ASTM D3039/D3039M: Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials Flexible materials • ASTM D638: Standard Test Method for Tensile Properties of Plastics • ASTM D828: Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus • ASTM D882: Standard Test Method for Tensile Properties of Thin Plastic Sheeting • ISO 37: Rubber, vulcanized or thermoplastic − Determination of tensile stress–strain properties ==References==