EPROM

Development of the EPROM memory cell started with investigation of faulty integrated circuits where the gate connections of transistors had broken. Stored charge on these isolated gates changes their threshold voltage. Following the invention of the MOSFET (metal–oxide–semiconductor field-effect transistor) by Mohamed Atalla and Dawon Kahng at Bell Labs, presented in 1960, Frank Wanlass studied MOSFET structures in the early 1960s. In 1963, he noted the movement of charge through oxide onto a gate. While he did not pursue it, this idea would later become the basis for EPROM technology. In 1967, Dawon Kahng and Simon Min Sze at Bell Labs proposed that the floating gate of a MOSFET could be used for the cell of a reprogrammable ROM (read-only memory). Building on this concept, Dov Frohman of Intel invented EPROM in 1971, Because of the high insulation value of the silicon oxide surrounding the gate, the stored charge cannot readily leak away and the data can be retained for decades. The programming process is not electrically reversible. To erase the data stored in the array of transistors, ultraviolet light is directed onto the die. Photons of the UV light cause ionization within the silicon oxide, which allows the stored charge on the floating gate to dissipate. Since the whole memory array is exposed, all the memory is erased at the same time. The process takes several minutes for UV lamps of convenient sizes; sunlight would erase a chip in weeks, and indoor fluorescent lighting over several years. Generally, the EPROMs must be removed from equipment to be erased, since it is not usually practical to build in a UV lamp to erase parts in-circuit. Electrically Erasable Programmable Read-Only Memory (EEPROM) was developed to provide an electrical erase function and has now mostly displaced ultraviolet-erased parts. ==Details==

AT27C010 - an OTP EPROM As the quartz window is expensive to make, OTP (one-time programmable) chips were introduced; here, the die is mounted in an opaque package so it cannot be erased after programming – this also eliminates the need to test the erase function, further reducing cost. OTP versions of both EPROMs and EPROM-based microcontrollers are manufactured. However, OTP EPROM (whether separate or part of a larger chip) is being increasingly replaced by EEPROM for small sizes, where the cell cost isn't too important, and flash for larger sizes. A programmed EPROM retains its data for a minimum of ten to twenty years, with many still retaining data after 35 or more years, and can be read an unlimited number of times without affecting the lifetime. The erasing window must be kept covered with an opaque label to prevent accidental erasure by the UV found in sunlight or camera flashes. Old PC BIOS chips were often EPROMs, and the erasing window was often covered with an adhesive label containing the BIOS publisher's name, the BIOS revision, and a copyright notice. Often this label was foil-backed to ensure its opacity to UV. Erasure of the EPROM begins to occur with wavelengths shorter than 400 nm. Exposure time for sunlight of one week or three years for room fluorescent lighting may cause erasure. The recommended erasure procedure is exposure to UV light at 253.7 nm of at least 15 Ws/cm2, usually achieved in 20 to 30 minutes with the lamp at a distance of about 2.5 cm. Erasure can also be accomplished with X-rays: EPROMs have a limited but large number of erase cycles; the silicon dioxide around the gates accumulates damage from each cycle, making the chip unreliable after several thousand cycles. EPROM programming is slow compared to other forms of memory. Because higher-density parts have little exposed oxide between the layers of interconnects and gate, ultraviolet erasing becomes less practical for very large memories. Even dust inside the package can prevent some cells from being erased. ==Application==

For large volumes of parts (thousands of pieces or more), mask-programmed ROMs are the lowest cost devices to produce. However, these require many weeks lead time to make, since the artwork or design in an IC mask layer or photomask must be altered to store data on the ROMs. Initially, it was thought that the EPROM would be too expensive for mass production use and that it would be confined to development only. It was soon found that small-volume production was economical with EPROM parts, particularly when the advantage of rapid upgrades of firmware was considered. Some microcontrollers, from before the era of EEPROMs and flash memory, use an on-chip EPROM to store their program. Such microcontrollers include some versions of the Intel 8048, the Freescale 68HC11, and the "C" versions of the PIC microcontroller. Like EPROM chips, such microcontrollers came in windowed (expensive) versions that were used for debugging and program development. The same chip came in (somewhat cheaper) opaque OTP packages for production. Leaving the die of such a chip exposed to light can also change behavior in unexpected ways when moving from a windowed part used for development to a non-windowed part for production. == EPROM generations, sizes and types ==

The first generation 1702 devices were fabricated with the p-MOS technology. They were powered with VCC = VBB = +5 V and VDD = VGG = -9 V in Read mode, and with VDD = VGG = -47 V in Programming mode. The second generation 2704 / 2708 devices switched to n-MOS technology and to three-rail VCC = +5 V, VBB = -5 V, VDD = +12 V power supply with VPP = 12 V and a +25 V pulse in Programming mode. The third generation 2716 / 2732 devices upgraded to an evolved n-MOS technology that required only a single-rail VCC = +5 V power supply for read operations, and a single VPP = +25 V programming voltage without pulse. The unneeded VBB and VDD pins were reused for additional address bits allowing larger capacities (2716 / 2732) in the same 24-pin package, and even larger capacities with larger packages. Later the decreased cost of the CMOS technology allowed the same devices to be fabricated using it, adding the letter "C" to the device numbers (27xx(x) are n-MOS and 27Cxx(x) are CMOS). While the industry was heading towards a standard pinout and architecture of the 27xx EPROMs, Texas Instruments (TI) introduced a few types that are now considered non-standard. While the TMS2716 was a three-rail device like preceding types, their TMS2516 was a single +5V EPROM like the 2716 offered by the other chip foundries. TI then released the TMS2532 and TMS2564, both single +5V devices, but with pinouts incompatible with the 2732 and 2764. While parts of the same size from different manufacturers are compatible in read mode, different manufacturers added different and sometimes multiple programming modes leading to subtle differences in the programming process. This prompted larger capacity devices to introduce a "signature mode", allowing the manufacturer and device to be identified by the EPROM programmer. It was implemented by forcing +12 V on pin A9 and reading out two bytes of data. However, as this was not universal, programmer software also would allow manual setting of the manufacturer and device type of the chip to ensure proper programming. ==Gallery==

ST Microelectronics M27C256B (2006) (cropped).jpg|A 32 KB (256 Kbit) EPROM. The -12 suffix indicates this device has a 120 nanosecond access time. KL_Intel_D8749.jpg|This 8749 Microcontroller stores its program in an internal EPROM. Nec 02716 EPROM.jpg|NEC 02716, 16 KBit EPROM Microcomputer with EPROM (piggyback).jpg|Piggyback microcontroller from MOSTEK with attached EPROM ==See also==