IEEE 802.11n-2009

IEEE 802.11n is an amendment to IEEE 802.11-2007 as amended by IEEE 802.11k-2008, IEEE 802.11r-2008, IEEE 802.11y-2008, and IEEE 802.11w-2009, and builds on previous 802.11 standards by adding a multiple-input multiple-output (MIMO) system and 40 MHz channels to the PHY (physical layer) and frame aggregation to the MAC layer. There were older proprietary implementations of MIMO and 40MHz channels such as Xpress, Super G and Nitro which were based upon 802.11g and 802.11a technology, but this was the first time it was standardized across all radio manufacturers. MIMO is a technology that uses multiple antennas to coherently resolve more information than possible using a single antenna. One way it provides this is through spatial division multiplexing (SDM), which spatially multiplexes multiple independent data streams, transferred simultaneously within one spectral channel of bandwidth. MIMO SDM can significantly increase data throughput as the number of resolved spatial data streams is increased. Each spatial stream requires a discrete antenna at both the transmitter and the receiver. In addition, MIMO technology requires a separate radio-frequency chain and analog-to-digital converter for each antenna, making it more expensive to implement than non-MIMO systems. Channels operating with a width of 40 MHz are another feature incorporated into 802.11n; this doubles the channel width from 20 MHz in previous 802.11 PHYs to transmit data, and provides twice the PHY data rate available over a single 20 MHz channel. It can be enabled in the 5 GHz mode, or within the 2.4 GHz mode if there is knowledge that it will not interfere with any other 802.11 or non-802.11 (such as Bluetooth) system using the same frequencies. The MIMO architecture, together with the wider channels, offers increased physical transfer rate over standard 802.11a (5 GHz) and 802.11g (2.4 GHz). Data encoding The transmitter and receiver use precoding and postcoding techniques, respectively, to achieve the capacity of a MIMO link. Precoding includes spatial beamforming and spatial coding, where spatial beamforming improves the received signal quality at the decoding stage. Spatial coding can increase data throughput via spatial multiplexing and increase range by exploiting the spatial diversity, through techniques such as Alamouti coding. Numbers of antennas and data streams The number of simultaneous data streams is limited by the minimum number of antennas in use on both sides of the link. However, the individual radios often further limit the number of spatial streams that may carry unique data. The notation helps identify what a given radio is capable of. The first number () is the maximum number of transmit antennas or transmitting TF chains that can be used by the radio. The second number () is the maximum number of receive antennas or receiving RF chains that can be used by the radio. The third number () is the maximum number of data spatial streams the radio can use. For example, a radio that can transmit on two antennas and receive on three, but can only send or receive two data streams, would be The 802.11n draft allows up to Common configurations of 11n devices are , , and . All three configurations have the same maximum throughputs and features, and differ only in the amount of diversity the antenna systems provide. In addition, a fourth configuration, is becoming common, which has a higher throughput, due to the additional data stream. Data rates Assuming equal operating parameters to an 802.11g network achieving 54 megabits per second (on a single 20 MHz channel with one antenna), an 802.11n network can achieve 72 megabits per second (on a single 20 MHz channel with one antenna and 400 ns guard interval); 802.11n's speed may go up to 150 megabits per second if there are not other Bluetooth, microwave or Wi-Fi emissions in the neighborhood by using two 20 MHz channels in 40 MHz mode. If more antennas are used, then 802.11n can go up to 288 megabits per second in 20 MHz mode with four antennas, or 600 megabits per second in 40 MHz mode with four antennas and 400 ns guard interval. Because the 2.4 GHz band is seriously congested in most urban areas, 802.11n networks usually have more success in increasing data rate by utilizing more antennas in 20 MHz mode rather than by operating in the 40 MHz mode, as the 40 MHz mode requires a relatively free radio spectrum which is only available in rural areas away from cities. Thus, network engineers installing an 802.11n network should strive to select routers and wireless clients with the most antennas possible (one, two, three or four as specified by the 802.11n standard) and try to make sure that the network's bandwidth will be satisfactory even on the 20 MHz mode. Data rates up to 600 Mbit/s are achieved only with the maximum of four spatial streams using one 40 MHz-wide channel. Various modulation schemes and coding rates are defined by the standard, which also assigns an arbitrary number to each; this number is the modulation and coding scheme index, or MCS index. The table below shows the relationships between the variables that allow for the maximum data rate. GI (Guard Interval): Timing between symbols. 20 MHz channel uses an FFT of 64, of which: 56 OFDM subcarriers, 52 are for data and 4 are pilot tones with a carrier separation of 0.3125 MHz (20 MHz/64) (3.2 μs). Each of these subcarriers can be a BPSK, QPSK, 16-QAM or 64-QAM. The total bandwidth is 20 MHz with an occupied bandwidth of 17.8 MHz. Total symbol duration is 3.6 or 4 microseconds, which includes a guard interval of 0.4 (also known as short guard interval (SGI)) or 0.8 microseconds. Frame aggregation PHY level data rate does not match user level throughput because of 802.11 protocol overheads, like the contention process, interframe spacing, PHY level headers (Preamble + PLCP) and acknowledgment frames. The main media access control (MAC) feature that provides a performance improvement is aggregation. Two types of aggregation are defined: • Aggregation of MAC service data units (MSDUs) at the top of the MAC (referred to as MSDU aggregation or A-MSDU) • Aggregation of MAC protocol data units (MPDUs) at the bottom of the MAC (referred to as MPDU aggregation or A-MPDU) Frame aggregation is a process of packing multiple MSDUs or MPDUs together to reduce the overheads and average them over multiple frames, thereby increasing the user level data rate. A-MPDU aggregation requires the use of block acknowledgement or BlockAck, which was introduced in 802.11e and has been optimized in 802.11n. Backward compatibility When 802.11g was released to share the band with existing 802.11b devices, it provided ways of ensuring backward compatibility between legacy and successor devices. 802.11n extends the coexistence management to protect its transmissions from legacy devices, which include 802.11g, 802.11b and 802.11a. There are MAC and PHY level protection mechanisms as listed below: • PHY level protection: Mixed Mode Format protection (also known as L-SIG TXOP Protection): In mixed mode, each 802.11n transmission is always embedded in an 802.11a or 802.11g transmission. For 20 MHz transmissions, this embedding takes care of the protection with 802.11a and 802.11g. However, 802.11b devices still need CTS protection. • PHY level protection: Transmissions using a 40 MHz channel in the presence of 802.11a or 802.11g clients require using CTS protection on both 20 MHz halves of the 40 MHz channel, to prevent interference with legacy devices. • MAC level protection: An RTS/CTS frame exchange or CTS frame transmission at legacy rates can be used to protect subsequent 11n transmission. == Deployment strategies ==

To achieve maximum output, a pure 802.11n 5 GHz network is recommended. The 5 GHz band has substantial capacity due to many non-overlapping radio channels and less radio interference as compared to the 2.4 GHz band. An 802.11n-only network may be impractical for many users because they need to support legacy equipment that still is 802.11b/g only. In a mixed-mode system, an optimal solution would be to use a dual-radio access point and place the 802.11b/g traffic on the 2.4 GHz radio and the 802.11n traffic on the 5 GHz radio. This setup assumes that all the 802.11n clients are 5 GHz capable, which is not a requirement of the standard. 5 GHz is optional on Wi-Fi 4; quite some Wi-Fi 4 capable devices only support 2.4 GHz and there is no practical way to upgrade them to support 5 GHz. Band steering Some enterprise-grade APs use band steering to send 802.11n clients to the 5 GHz band, leaving the 2.4 GHz band for legacy clients. Band steering works by responding only to 5 GHz association requests and not the 2.4 GHz requests from dual-band clients. 40 MHz channels in 2.4 GHz The 2.4 GHz ISM band is fairly congested. With 802.11n, there is the option to double the bandwidth per channel to 40 MHz (fat channel) which results in slightly more than double the data rate. However, in North America, when in 2.4 GHz, enabling this option takes up to 82% of the unlicensed band. For example, channel 3 SCA (secondary channel above), also known as 3+7, reserves the first 9 out of the 11 channels available. In Europe and other places where channels 1–13 are available, allocating 1+5 uses slightly more than 50% of the channels, but the overlap with 9+13 is not usually significant as it lies at the edges of the bands, and so two 40 MHz bands typically work unless the transmitters are physically very closely spaced. The specification calls for requiring one primary 20 MHz channel as well as a secondary adjacent channel spaced ±20 MHz away. The primary channel is used for communications with clients incapable of 40 MHz mode. When in 40 MHz mode, the center frequency is actually the mean of the primary and secondary channels. Local regulations may restrict certain channels from operation. For example, Channels 12 and 13 are normally unavailable for use as either a primary or secondary channel in North America. For further information, see List of WLAN channels. ==Wi-Fi Alliance certification program==

The Wi-Fi Alliance has upgraded its suite of compatibility tests for some enhancements that were finalized after a 2.0. Furthermore, it has affirmed that all draft-n certified products remain compatible with the products conforming to the final standards. draft-n After the first draft of the IEEE 802.11n standard was published in 2006, many manufacturers began producing so-called "draft-n" products that claimed to comply with the standard draft, even before standard finalization which mean they might not be inter-operational with products produced according to IEEE 802.11 standard after the standard publication, nor even among themselves. The Wi-Fi Alliance began certifying products based on IEEE 802.11n draft 2.0 mid-2007. This certification program established a set of features and a level of interoperability across vendors supporting those features, thus providing one definition of "draft n" to ensure compatibility and interoperability. The baseline certification covers both 20 MHz and 40 MHz wide channels, and up to two spatial streams, for maximum throughputs of 144.4 Mbit/s for 20 MHz and 300 Mbit/s for 40 MHz (with short guard interval). A number of vendors in both the consumer and enterprise spaces have built products that have achieved this certification. == Timeline ==

The following are milestones in the development of 802.11n: ;September 11, 2002: The first meeting of the High-Throughput Study Group (HTSG) was held. Earlier in the year, in the Wireless Next Generation standing committee (WNG SC), presentations were heard on why they need change and what the target throughput would be required to justify the amendments. Compromise was reached in May 2002 to delay the start of the Study Group until September to allow 11g to complete major work during the July 2002 session. ;September 11, 2003: The IEEE-SA New Standards Committee (NesCom) approved the Project Authorization Request (PAR) for the purpose of amending the 802.11-2007 standard. The new 802.11 Task Group (TGn) is to develop a new amendment. The TGn amendment is based on IEEE Std 802.11-2007, as amended by IEEE Std 802.11k-2008, IEEE Std 802.11r-2008, IEEE Std 802.11y-2008 and IEEE P802.11w. TGn will be the 5th amendment to the 802.11-2007 standard. The scope of this project is to define an amendment that shall define standardized modifications to both the 802.11 physical layers (PHY) and the 802.11 Medium Access Control Layer (MAC) so that modes of operation can be enabled that are capable of much higher throughputs, with a maximum throughput of at least 100 Mbit/s, as measured at the MAC data service access point (SAP). ;September 15, 2003: The first meeting of the new 802.11 Task Group (TGn). ;May 17, 2004: Call for Proposals was issued. ;September 13, 2004: 32 first round of proposals were heard. ;March 2005: Proposals were downselected to a single proposal, but there is not a 75% consensus on the one proposal. Further efforts were expended over the next 3 sessions without being able to agree on one proposal. ;July 2005: Previous competitors TGn Sync, WWiSE, and a third group, MITMOT, said that they would merge their respective proposals as a draft. The standardization process was expected to be completed by the second quarter of 2009. ; January 19, 2006: The IEEE 802.11n Task Group approved the Joint Proposal's specification, enhanced by EWC's draft specification. Unanimous approval to send Final WG draft 11.0 to RevCom. ;September 11, 2009: RevCom/Standards Board approval. ;October 29, 2009: Published. == Comparison ==

• • IEEE 802.11n-2009 ==Notes==