, by
Lee Richmond, 1880. Abbreviations: A, B, C, for first, second and third, P and H for pitcher and catcher, S for shortstop, L, M, and R for left, center, and right field There is no authoritative set of rules for scorekeeping. The traditional method has many variations in its symbols and syntax, but this is a typical example. In the traditional method, each cell in the main area of the scoresheet represents the "lifetime" of an offensive player, from at-bat, to baserunner, to being put out, scoring a run, or being left on base.
Outs When an out is recorded, the combination of defensive players executing that out is recorded. For example: • If a batter hits a ball on the ground to the shortstop, who throws the ball to the first baseman to force the first out, it would be noted on the scoresheet as
6–3, with
6 for the shortstop and
3 for the first baseman. • If the next batter hits a ball to the center fielder who catches it on the fly for the second out, it would be noted as
F8, with
F for
flyout and
8 for the center fielder. (In some systems, the letter 'F' is reserved for foul outs. A fly out would therefore be scored simply as '8'.) Other systems append a lower-case "ƒ" for foul balls, as in
F9ƒ . • If the following batter strikes out, it would be noted as
K, with the
K being the standard notation for a strikeout. If the batter did not swing at the third strike, a "backwards K" (
K, see right) is traditionally used. Other forms include "Kc" for a called third strike with no swing, or "Ks" if the batter did swing. A slash should be drawn across the lower right corner to indicate the end of the inning. • If a runner is put out while on base, the next basepath is filled-in halfway, then ended with a short stroke perpendicular to the basepath. A notation is then added to indicate how the runner was out, along with the defensive combination that resulted in the out: •
CS means the runner was caught trying to steal the base ahead. The notation for a runner caught trying to steal second is normally
2–4 or
2–6 for a catcher-to-second-base play. •
PK means the runner was
picked off by the pitcher while he was off the base. This almost always occurs at first base, so the notation is usually
1–3. •
DP or
TP means the runner was out as part of a
double or
triple play. Usually, the full notation is left on the batter's line (the last out of the play);
6–4–3,
4–6–3, and
5–4–3 are common double-play sequences. •
FC means the out was the result of a
fielder's choice to get out the runner on base rather than force out the batter. This can also be indicative of an unsuccessful attempt at a double or triple play as such a move is often the first move to make such a play.
Reaching base If a batter reaches first base, either due to a walk, a hit, or an error, the basepath from home to first base is drawn, and the method described in the lower-righthand corner. For example: • If a batter gets a base hit, the basepath is drawn and
1B or
– (for a single-base hit) is written below. • If the batter hits a
double, however, the basepaths from home to first and first to second are drawn, and
2B or
= is written
above. This change of position is done to indicate that the runner did not advance on another hit. If the batter hits a
triple, the basepaths are drawn from home to first to second to third and
3B or
≡ is written in the
upper lefthand corner for the same reason. • If a batter gets a walk, the basepath is drawn and
BB (for
Base on Balls) or
W (for Walk) is written below.
IBB is written for an
intentional base on balls. Other indicators may be used if the batter is awarded first base for other reasons (
HBP for being
hit by a pitch,
CI for
catcher's interference, etc.). • If the batter reaches first base due to
fielder's choice (ex. the shortstop decides to force out the runner heading to second instead), the basepath is drawn and
FC is written along with the sequence of the defense's handling of the ball, e.g., 6–4. • If the batter reaches base because the first baseman dropped the throw from the shortstop, the basepath is drawn and
E3 (an error committed by the first baseman) is written below. • If a batter gets a base hit then in the same play advances due to a fielding error by the second baseman (for example he misses the throw from the outfield, allowing the ball to get away), these are written as two events. First, the path to first is drawn with a
1B noted as for a single, then the path to second is drawn with an
E4 noted above. This correctly describes the scoring—a single
plus an error.
Advancing When a runner advances due to a following batter, it can be noted by the batting position or the uniform number of the batter that advanced the runner. This kind of information is not always included by amateur scorers, and there is a lot of variation in notation. For example: • If a runner on first is advanced to third base due to action from the 4th batter, number 22, the paths from first to second to third are drawn in and either a
4 or
22 could be written in the upper left hand corner. Whether that action was a base hit or a sacrifice will be noted on the batter's annotation. • If a runner steals second while the 7th batter, number 32, is up to bat, the path from first to second would be drawn and
SB followed by either a
7 or
32 could be written in the upper right hand corner. Note that Defensive Indifference (no attempt to throw out the runner) is denoted differently from a Stolen Base. • For a batter to be credited with advancing the runner, the base advance must be the result of the batter's action. If a runner advances beyond that due to an error (such as a bad catch) or a fielder's choice (such as a throw to tag out a runner ahead of him), the advance due to the batter's action and the advance due to the other action are noted separately. • To advance a player home to score a run, a runner must touch all 4 bases and cross all four base paths, therefore the scorer draws a complete diamond and, usually, fills it in. However, some scorers only fill in the diamond on a home run; they might then place a small dot in the center of the diamond to indicate a run scored but not a home run. The player that bats the runner home (or the other event such as an error that allows the runner to reach home) is noted in the lower left hand corner.
Miscellaneous • End of an inning – When the offensive team has made three outs, a slash is drawn diagonally across the lower right corner of the cell of the third out. After each half-inning, the total number of hits and runs can be noted at the bottom of the column. After the game, totals can be added up for each team and each batter. • Extra innings – There are extra columns on a scoresheet that can be used if a game goes to extra innings, but if a game requires more columns, another scorecard will be needed for each team. • Substitutions – When a substitution is made, a vertical line is drawn after the last at-bat for previous player, and the new player's name and number is written in the second line of the Player Information section. A notation of
PH or
PR should be made for pinch hit and pinch run situations. • Batting around – After the ninth batter has batted, the record of the first batter should be noted in the same column. However, if more than nine batters bat in a single inning, the next column will be needed. Draw a diagonal line across the lower left hand corner, to indicate that the original column is being extended. ==Alternative systems==