C0 and C1 control codes

ASCII defines 32 control characters, plus the DEL character. This large number of codes was desirable at the time, as multi-byte controls would require implementation of a state machine in the terminal, which was very difficult with contemporary electronics and mechanical terminals. Only a few codes have maintained their use: BEL, ESC, and the format effector (FEn) characters BS, HT, LF, VT, FF, and CR. Others are unused or have acquired different meanings such as NUL being the C string terminator. Some data transfer protocols such as ANPA-1312, Kermit, and XMODEM do make extensive use of SOH, STX, ETX, EOT, ACK, NAK and SYN for purposes approximating their original definitions; and some file formats use the "Information Separators" (ISn) such as the Unix info format and Python's string method. The names of some codes were changed in ISO 6429:1992 (or ECMA-48:1991) to be neutral with respect to writing direction. The abbreviations used were not changed, as the standard had already specified that those would remain unchanged when the standard is translated to other languages. In this table both new and old names are shown for the renamed controls (the old name is the one matching the abbreviation). Unicode provides Control Pictures that can replace C0 control characters to make them visible on screen. However caret notation is used more often. == C1 controls ==

In 1973, ECMA-35 and ISO 2022 attempted to define a method so an 8-bit "extended ASCII" code could be converted to a corresponding 7-bit code, and vice versa. (i.e. all but the C0 control codes), to be the characters that an 8-bit environment would print if it used the same code with the high bit set. This meant that the range through could not be printed in a 7-bit environment, thus it was decided that no alternative character set could use them, and that these codes should be additional control codes, which become known as the C1 control codes. To allow a 7-bit environment to use these new controls, the sequences ESC @ through ESC _ were to be considered equivalent. and JIS X 0211 (formerly JIS C 6323). Symbolic names defined by and early drafts of ISO 10646, but not in ISO/IEC 6429 (, and ) are also used. Except for and in EUC-JP text, and in text transcoded from EBCDIC, the 8-bit forms of these codes were almost never used. , and are used to control text terminals and terminal emulators, but almost always by using their 7-bit escape code representations. Nowadays if these codes are encountered it is far more likely they are intended to be printing characters from that position of Windows-1252 or Mac OS Roman. Except for , Unicode does not provide a "control picture" for any of these. There is no well-known variation of Caret notation for them either. == Other control code sets ==

The ISO/IEC 2022 (ECMA-35) extension mechanism allowed escape sequences to change the C0 and C1 sets. The standard C0 control character set shown above is chosen with the sequence and the above C1 set chosen with the sequence . SP and DEL "fixed" coded characters, which are available in their ASCII locations in all encodings that conform to the standard. It also specifies that if a C0 set included transmission control (TCn) codes, they must be encoded at their ASCII locations and could not be put in a C1 set, and any new transmission controls must be in a C1 set. and others replaced EM and GS with SS2 and SS3 so these functions could be used in a 7-bit environment without resorting to escape sequences. • Some sets replaced FS with SS2, (same as ANPA-1312). • The now-withdrawn JIS C 6225, designated JIS X 0207 in later sources. replaced FS with CEX or "Control Extension" which introduces control sequences for vertical text behaviour, superscripts and subscripts and for transmitting custom character graphics. • Various specialised C1 control code sets are registered for use by Videotex formats. It includes SS1 (Single-Shift 1) through SS15 (Single-Shift 15) controls, used to invoke individual characters from pre-defined supplementary character sets, in a similar manner to the single-shift mechanism of ISO/IEC 2022. The only single-shift controls defined by ISO/IEC 2022 are SS2 and SS3; these are retained in the VOS set at their original code points and function the same way. • EBCDIC defines up to 29 additional control codes besides those present in ASCII. When translating EBCDIC to Unicode (or to ISO 8859), these codes are mapped to C1 control characters in a manner specified by IBM's Character Data Representation Architecture (CDRA). Although the New Line (NL) does translate to the ISO/IEC 6429 (although it is often swapped with LF, following UNIX line ending convention), ==Unicode==

Unicode reserves the 65 code points described above for compatibility with the C0 and C1 control codes, giving them the general category (control). These are: • (C0 controls) and (DEL) assigned to the C0 Controls and Basic Latin block, and • (C1 controls) assigned to the C1 Controls and Latin-1 Supplement block. Unicode only specifies semantics for the C0 format controls HT, LF, VT, FF, and CR (note BS is missing); the C0 information separators FS, GS, RS, US (and SP); and the C1 control NEL. Unicode includes many additional format effector characters besides these, such as marks, embeds, isolates and pops for explicit bidirectional formatting, and the zero-width joiner and non-joiner for controlling ligature use. However these are given the general category (format) rather than . ==See also==