EMD E-unit

9911A, an EMD E5, operating at the Illinois Railway Museum, July 18, 2004. The EA/EB, E1, and E2 models were powered by twin 900 hp Winton 201A V-12 engines in each power unit. They were standardized mechanically and in overall design. Union Pacific's E2 cab unit was distinguished from the slant-nosed EA and E1 units by its bulbous nose, round porthole style windows, and stainless steel ornamentation on the pilot and nose. The "E" designation originated to denote the locomotive units' Eighteen hundred horsepower, as opposed to the Twelve hundred horsepower "T" units but was later used to refer to all carbody constructed twin-engine mainline passenger locomotives units produced by EMC. Their twin V-12 diesel engine layout, Blomberg A-1-A trucks, and wheelbase would become the standard for all future E models. EMC/EMD has built all of its major components since 1939. The E3, E4, E5, and E6 had the new GM-EMC 567 purpose-designed locomotive engines, for a total of . They had the sharply raked "slant nose", and square windows on the sides (with the exception of Union Pacific orders with porthole style windows). Production stopped in 1942. The E5 designation was used for Chicago Burlington and Quincy's stainless steel clad locomotives in keeping with their Zephyr theme. The EA/EB, E1, E2, E4, and E5 model names reflected EMC's early convention of assigning a model name for each individual customer order. EMC started to change that convention with the multiple-customer E3 model and the new naming convention was fully incorporated with the E6 model. The E7 was introduced in 1945, and became the best selling E model. It had the improved 567 "A" engine, and the F style "bulldog nose". The E8 and E9 were the final E models. The E8 had 12-V567B engines ( total), while the E9 had uprated 12V-567C engines ( total). They both used the same body style, with a grille along the top of the sides the length of the loco, and several "porthole" windows below it. Model descriptions are as originally built; EMC/EMD locomotives are often rebuilt to newer standards. == Engines ==

While there were some cosmetic differences between E-unit models, the major line of development was technological, and largely that of increasing power. The first model, the EA/EB, was rated at 1800 hp (1300 kW), then the E3 was rated at 2,000 hp. The last model, the E9, was rated at 2,400 hp (1800 kW). Early models (EA/EB through E2) used the Winton 201-A engine that had been developed in the early 1930s by the partnership of General Motors and Winton. While this engine represented a breakthrough in power-to-weight ratios and output flexibility for Diesel engines, it was a compromise between marine and locomotive requirements and wasn't well suited to the sustained full throttle operation often needed in railroad service. It was not unusual for heavy repairs to be done en route on one engine while the other engine propelled the train at reduced speed. The 201-A engines used in E-units were 900 hp (700 kW) V12s. Experience with the 201-A, which was the first two-stroke Diesel engine in operational use, was invaluable in the development of the next-generation Diesel engine, the EMD 567, a purpose-designed engine that achieved a factor-of-five improvement in piston life for locomotive use. The E3 introduced the 567 series engine, which would power all later E units, the 567 being a mechanically aspirated two stroke 45 degree V-type with displacement per cylinder, a total of per engine. Models E3 through E9 used the EMD model 567 engine, named after its engine displacement in cubic inches per cylinder. The 567 model had been developed by EMD specifically for locomotive use, and exhibited excellent performance and reliability in high speed passenger train service. The 567 had a greater displacement per cylinder than the 201-A and ran at a higher maximum rpm, elements which when combined gave greater engine output. The 12V-567 V12 model used in the E3 through E6 developed 1000 hp (750 kW). The E7 model used the 12V-567A rated at 1000 hp (750 kW). The E8 used the more advanced 567B unit, with improved exhaust manifolds and other enhancements to give 1,125 hp each. More development resulted in the 1200 hp (900 kW) 567C engine used in the E9. == Trucks ==

All E-units used the same EMD passenger truck design by engineer Martin Blomberg. This was an A1A-A1A truck, with the outer axles powered and the center axle unpowered. Like the well-known two-axle Blomberg B trucks, these trucks had outside spring hangers between the wheels for better cushioning of side-to-side motion. Also like the Blomberg B, there were no drop equalizers between the axles. Two direct current generators powered four traction motors, two on each truck, in an A1A-A1A arrangement. This truck design was used on all E units and on CB&Q 9908 and MP 7100 power cars. The success of the design is shown by the few changes to it over the years. == Styling ==

The EA and E1 had sloping noses with recessed headlights, while the E2 had a more bulbous "bulldog" nose. Models E3 through E6 had a sloping nose but with a protruding headlight, while models E7 through E9 used a less sloped (closer to vertical) style like the freight F-units. A patent of 1937 signed by several EMC engineers defined the styling. Many older E-units were updated to newer styles. The E8 introduced the one-piece stamped Farr stainless-steel side grilles that made a continuous band from front to rear just below the roof, but these were often retrofitted to earlier units. Side windows were half-rounded on the EA/EB, square on the E1, round on the E2, square on most E3 through E7 units, and rounded portholes again on the E8 and E9, but again many railroads updated older locomotives. The E5 units were unique, produced for the Chicago, Burlington and Quincy Railroad in all stainless steel with fluted lower carbody sides, to match the railroad's Zephyr passenger trains. == Other changes ==

Other improvements occurred independently of the change in engine design. The E8, for example, was the first model to incorporate electric cooling fans, and offer dynamic braking as an option. ==Models==

A number of E-units survive, many are in good running order. Several railroads retain sets that haul passenger specials, management inspection specials, etc. Others survive in museums or on short lines. The Illinois Railway Museum in Union, Illinois has one of the largest collections of operable and preserved E's including CB&Q E5 9911A and WSOR 102, one of the few remaining operable B units. The Southeastern Railway Museum in Duluth, Georgia has Southern Railway #6901, an E8 that once powered the Southern Crescent. == References ==