Network switch

A switch is a device in a computer network that connects other devices together. Multiple data cables are plugged into a switch to enable communication between different networked devices. Switches manage the flow of data across a network by transmitting a received network packet only to the one or more devices for which the packet is intended. Each networked device connected to a switch can be identified by its network address, allowing the switch to direct the flow of traffic, maximizing the security and efficiency of the network. A switch is more intelligent than an Ethernet hub, which simply retransmits packets out of every port of the hub except the port on which the packet was received, unable to distinguish different recipients, and achieves an overall lower network efficiency. An Ethernet switch operates at the data link layer (layer 2) of the OSI model to create a separate collision domain for each switch port. Each device connected to a switch port can transfer data to any of the other ports at any time and the transmissions will not interfere. Because broadcasts are still being forwarded to all connected devices by the switch, the newly formed network segment continues to be a broadcast domain. Switches may also operate at higher layers of the OSI model, including the network layer and above. A switch that also operates at these higher layers is known as a multilayer switch. Segmentation involves the use of a switch to split a larger collision domain into smaller ones in order to reduce collision probability and to improve overall network throughput. In the extreme case (i.e., micro-segmentation), each device is directly connected to a switch port dedicated to the device. In contrast to an Ethernet hub, there is a separate collision domain on each switch port. This allows computers to have dedicated bandwidth on point-to-point connections to the network and also to run in full-duplex mode. Full-duplex mode has only one transmitter and one receiver per collision domain, making collisions impossible. The network switch plays an integral role in most modern Ethernet local area networks (LANs). Mid-to-large-sized LANs contain a number of linked managed switches. Small office/home office (SOHO) applications typically use a single switch, or an all-purpose device such as a residential gateway to access small office/home broadband services such as DSL or cable Internet. In most of these cases, the end-user device contains a router and components that interface to the particular physical broadband technology. Many switches have pluggable modules, such as Small Form-factor Pluggable (SFP) modules. These modules often contain a transceiver that connects the switch to a physical medium, such as a fiber optic cable. Alternatively, DAC (Direct Attach Copper) cables may be used in place of modules. These modules were preceded by Medium Attachment Units connected via Attachment Unit Interfaces to switches and have evolved over time: the first modules were Gigabit interface converters, followed by XENPAK modules, SFP modules, XFP transceivers, SFP+ modules, QSFP, QSFP-DD, and OSFP modules. Pluggable modules are also used for transmitting video in broadcast applications. With the advent of increased speeds together with Co-packaged optics (CPO), which bring the transceivers close to the switching chip of the switch, reducing power consumption, pluggable modules become replaceable laser light sources, and fiber optics are connected directly to the front of the switch instead of through pluggable modules. CPO is also considerably easier to adapt to water cooling. == Role in a network ==

Switches are most commonly used as the network connection point for hosts at the edge of a network. In the hierarchical internetworking model and similar network architectures, switches are also used deeper in the network to provide connections between the switches at the edge. In switches intended for commercial use, built-in or modular interfaces make it possible to connect different types of networks, including Ethernet, Fibre Channel, RapidIO, ATM, ITU-T G.hn and 802.11. This connectivity can be at any of the layers mentioned. While the layer-2 functionality is adequate for bandwidth-shifting within one technology, interconnecting technologies such as Ethernet and Token Ring is performed more easily at layer 3 or via routing. Devices that interconnect at the layer 3 are traditionally called routers. Where there is a need for a great deal of analysis of network performance and security, switches may be connected between WAN routers as places for analytic modules. Some vendors provide firewall, network intrusion detection, and performance analysis modules that can plug into switch ports. Some of these functions may be on combined modules. Through port mirroring, a switch can create a mirror image of data that can go to an external device, such as intrusion detection systems and packet sniffers. A modern switch may implement power over Ethernet (PoE), which avoids the need for attached devices, such as a VoIP phone or wireless access point, to have a separate power supply. Because switches can have their power circuits connected to uninterruptible power supplies, the connected device can continue operating even when regular office power fails. In 1989 and 1990, Kalpana introduced the first multiport Ethernet switch, its seven-port EtherSwitch. == Bridging ==

Modern commercial switches primarily use Ethernet interfaces. The core function of an Ethernet switch is to provide multiple ports of layer-2 bridging. Layer-1 functionality is required in all switches in support of the higher layers. Many switches also perform operations at other layers. A device capable of more than bridging is known as a multilayer switch. A layer 2 network device is a multiport device that uses hardware addresses (MAC addresses) to process and forward data at the data link layer (layer 2). A switch operating as a network bridge may interconnect otherwise separate layer 2 networks. The bridge learns the MAC address of each connected device, storing this data in a table that maps MAC addresses to ports. This table is often implemented using high-speed content-addressable memory (CAM), some vendors refer to the MAC address table as a CAM table. Bridges also buffer an incoming packet and adapt the transmission speed to that of the outgoing port. While there are specialized applications, such as storage area networks, where the input and output interfaces are the same bandwidth, this is not always the case in general LAN applications. In LANs, a switch used for end-user access typically concentrates lower bandwidth and uplinks into a higher bandwidth. The Ethernet header at the start of the frame contains all the information required to make a forwarding decision; some high-performance switches can begin forwarding the frame to the destination whilst still receiving the frame payload from the sender. This cut-through switching can significantly reduce latency through the switch. Interconnects between switches may be regulated using the Spanning Tree Protocol (STP) that disables forwarding on links so that the resulting local area network is a tree without switching loops. In contrast to routers, spanning tree bridges must have topologies with only one active path between two points. Shortest path bridging and TRILL (Transparent Interconnection of Lots of Links) are layer 2 alternatives to STP, which allow all paths to be active with multiple equal cost paths. == Types ==

24-port 3Com switch Form factors Switches are available in many form factors, including stand-alone, desktop units which are typically intended to be used in a home or office environment outside a wiring closet; rack-mounted switches for use in an equipment rack or an enclosure; DIN rail mounted for use in industrial environments; and small installation switches, mounted into a cable duct, floor box or communications tower, as found, for example, in fiber to the office infrastructures. Rack-mounted switches may be stand-alone units, stackable switches or large chassis units with swappable line cards. Configuration options • es have no configuration interface or options. They are plug and play. They are typically the least expensive switches, and therefore often used in a small office/home office environment. Unmanaged switches can be desktop or rack mounted. • Managed switches have one or more methods to modify the operation of the switch. Common management methods include: a command-line interface (CLI) accessed via serial console, telnet or Secure Shell, an embedded Simple Network Management Protocol (SNMP) agent allowing management from a remote console or management station, or a web interface for management from a web browser. Two sub-classes of managed switches are smart and enterprise-managed switches. • Enterprise managed switches (aka managed switches) have a full set of management features, including CLI, SNMP agent, and web interface. They may have additional features to manipulate configurations, such as the ability to display, modify, backup and restore configurations. Compared with smart switches, enterprise switches have more features that can be customized or optimized and are generally more expensive than smart switches. Enterprise switches are typically found in networks with a larger number of switches and connections, where centralized management is a significant savings in administrative time and effort. A stackable switch is a type of enterprise-managed switch. Typical management features Gigabit Ethernet rackmount switches, connected to the Ethernet ports on a few patch panels using Category 6 patch cables (all installed in a standard 19-inch rack) • Centralized configuration management and configuration distribution • Enable and disable ports • Link bandwidth and duplex settings • Quality of service configuration and monitoring • MAC filtering and other access control list features • Configuration of Spanning Tree Protocol (STP) and Shortest Path Bridging (SPB) features • Simple Network Management Protocol (SNMP) monitoring of device and link health • Port mirroring for monitoring traffic and troubleshooting • Link aggregation configuration to set up multiple ports for the same connection to achieve higher data transfer rates and reliability • VLAN configuration and port assignments including IEEE 802.1Q tagging • NTP (Network Time Protocol) synchronization • Network access control features such as IEEE 802.1X • LLDP (Link Layer Discovery Protocol) • IGMP snooping for control of multicast traffic ==Traffic monitoring==

It is difficult to monitor traffic that is bridged using a switch because only the sending and receiving ports can see the traffic. Methods that are specifically designed to allow a network analyst to monitor traffic include: • Port mirroring Because the purpose of a switch is to not forward traffic to network segments where it would be superfluous, a node attached to a switch cannot monitor traffic on other segments. Port mirroring is how this problem is addressed in switched networks: In addition to the usual behavior of forwarding frames only to ports through which they might reach their addressees, the switch forwards frames received through a given monitored port to a designated monitoring port, allowing analysis of traffic that would otherwise not be visible through the switch. • Switch monitoring (SMON) is described by RFC 2613 and is a provision for controlling facilities such as port mirroring. • RMON • sFlow These monitoring features are rarely present on consumer-grade switches. Other monitoring methods include connecting a layer-1 hub or network tap between the monitored device and its switch port. == See also ==