Fractional distillation in a laboratory makes use of common
laboratory glassware and apparatuses, typically including a heat source such as a
heating mantle or hot plate and
sand bath (almost never an open flame as shown in the illustration, since a large majority of organic reagents are highly flammable), a
round-bottomed flask and a
condenser, as well as the single-purpose
fractionating column. The apparatus is assembled as in the diagram. (The diagram represents a batch apparatus as opposed to a continuous apparatus.) The mixture is put into the round-bottomed flask along with a few
anti-bumping granules (or a Teflon-coated magnetic stirrer bar if using
magnetic stirring), and the fractionating column is fitted into the top. The fractional distillation column is set up with the heat source at the bottom of the still pot. As the distance from the still pot increases, a temperature gradient is formed in the column; it is coolest at the top and hottest at the bottom. As the mixed vapor ascends the temperature gradient, some of the vapor condenses and vaporizes along the
temperature gradient. Each time the vapor condenses and vaporizes, the composition of the more volatile component in the vapor increases. This distills the vapor along the length of the column, and eventually, the vapor is composed solely of the more volatile component (or an
azeotrope). The vapor
condenses on the glass platforms, known as
trays, inside the column, and runs back down into the liquid below,
refluxing distillate. The efficiency in terms of the amount of heating and time required to get fractionation can be improved by insulating the outside of the column in an insulator such as wool, aluminum foil, or preferably a vacuum jacket. The hottest tray is at the bottom and the coolest is at the top. At steady-state conditions, the vapor and liquid on each tray are at
equilibrium. The most volatile component of the mixture exits as a
gas at the top of the column. The vapor at the top of the column then passes into the condenser, which cools it down until it liquefies. The separation is more pure with the addition of more trays (to a practical limitation of heat, flow, etc.) Initially, the condensate will be close to the azeotropic composition, but when much of the ethanol has been drawn off, the condensate becomes gradually richer in water. The process continues until all the ethanol boils out of the mixture. This point can be recognized by the sharp rise in temperature shown on the
thermometer. The explanation above reflects the theoretical way fractionation works. Normal laboratory fractionation columns will be simple glass tubes (often vacuum-jacketed, and sometimes internally
silvered) filled with a packing, often small glass helices of diameter. Such a column can be calibrated by the distillation of a known mixture system to quantify the column in terms of number of theoretical trays. To improve fractionation the apparatus is set up to return condensate to the column by the use of some sort of reflux splitter (reflux wire, gago, Magnetic swinging bucket, etc.) – a typical careful fractionation would employ a reflux ratio of around 4:1 (4 parts returned condensate to 1 part condensate take off). In laboratory distillation, several types of condensers are commonly found. The
Liebig condenser is simply a straight tube within a
water jacket and is the simplest (and relatively least expensive) form of condenser. The
Graham condenser is a spiral tube within a water jacket, and the
Allihn condenser has a series of large and small constrictions on the inside tube, each increasing the surface area upon which the vapor constituents may condense. Alternate set-ups may use a multi-outlet distillation receiver flask (referred to as a "cow" or "pig") to connect three or four receiving
flasks to the condenser. By turning the cow or pig, the distillates can be channeled into any chosen receiver. Because the receiver does not have to be removed and replaced during the distillation process, this type of apparatus is useful when distilling under an inert atmosphere for
air-sensitive chemicals or at reduced pressure. A
Perkin triangle is an alternative apparatus often used in these situations because it allows isolation of the receiver from the rest of the system, but does require removing and reattaching a single receiver for each fraction.
Vacuum distillation systems operate at reduced pressure, thereby lowering the boiling points of the materials.
Anti-bumping granules, however, become ineffective at reduced pressures. Some mixtures cannot be completely purified by fractional distillation. As an example, consider the distillation of a mixture of water and
ethanol. Ethanol boils at while water boils at . In this case an
azeotrope is also formed, where the mixture of ethanol and water boils at ; even if this temperature weren't near enough to ethanol's own boiling to that it would be nearly impossible to fractionally separate the mixture, the first fraction would always come over as the 96/4 azeotrope. In these cases,
azeotropic distillation or another method must be used instead. ==Industrial distillation==