Hydrofoil

The hydrofoil usually consists of a winglike structure mounted on struts below the hull, or across the keels of a catamaran in a variety of boats (see illustration). As a hydrofoil-equipped watercraft increases in speed, the hydrofoil elements below the hull(s) develop enough lift to raise the hull out of the water, which greatly reduces hull drag. This provides a corresponding increase in speed and fuel efficiency. Wider adoption of hydrofoils is prevented by the increased complexity of building and maintaining them. Hydrofoils are generally prohibitively more expensive than conventional watercraft above a certain displacement, so most hydrofoil craft are relatively small, and are mainly used as high-speed passenger ferries, where the relatively high passenger fees can offset the high cost of the craft itself. However, the design is simple enough that there are many human-powered hydrofoil designs. Amateur experimentation and development of the concept is popular. ==Hydrodynamic mechanics==

Since air and water are governed by similar fluid equations—albeit with different levels of viscosity, density, and compressibility—the hydrofoil and airfoil (both types of foil) create lift in identical ways. The foil shape moves smoothly through the water, deflecting the flow downward, which, following the Euler equations, exerts an upward force on the foil. This turning of the water creates higher pressure on the bottom of the foil and reduced pressure on the top. This pressure difference is accompanied by a velocity difference, via Bernoulli's principle, so the resulting flow field about the foil has a higher average velocity on one side than the other. When used as a lifting element on a hydrofoil boat, this upward force lifts the body of the vessel, decreasing drag and increasing speed. The lifting force eventually balances with the weight of the craft, reaching a point where the hydrofoil no longer lifts out of the water but remains in equilibrium. Since wave resistance and other impeding forces such as various types of drag (physics) on the hull are eliminated as the hull lifts clear, turbulence and drag act increasingly on the much smaller surface area of the hydrofoil, and decreasingly on the hull, creating a marked increase in speed. Foil configurations Early hydrofoils used V-shaped foils. Hydrofoils of this type are known as "surface-piercing" since portions of the V-shape hydrofoils rise above the water surface when foilborne. Some modern hydrofoils use fully submerged inverted T-shape foils. Fully submerged hydrofoils are less subject to the effects of wave action, and, therefore, more stable at sea and more comfortable for crew and passengers. This type of configuration, however, is not self-stabilizing. The angle of attack on the hydrofoils must be adjusted continuously to changing conditions, a control process performed by sensors, a computer, and active surfaces. == History ==

hydrofoil over Lake Maggiore, 1906 Prototypes The first evidence of a hydrofoil on a vessel appears on a British patent granted in 1869 to Emmanuel Denis Farcot, a Parisian. He claimed that "adapting to the sides and bottom of the vessel a series or inclined planes or wedge formed pieces, which as the vessel is driven forward will have the effect of lifting it in the water and reducing the draught.". Italian inventor Enrico Forlanini began work on hydrofoils in 1898 and used a "ladder" foil system. Forlanini obtained patents in Britain and the United States for his ideas and designs. Between 1899 and 1901, British boat designer John Thornycroft worked on a series of models with a stepped hull and single bow foil. In 1909 his company built the full scale long boat, Miranda III. Driven by a engine, it rode on a bowfoil and flat stern. The subsequent Miranda IV was credited with a speed of . 's HD-4 on a test run, c. 1919 In May 1904 a hydrofoil boat was described being tested on the River Seine "in the neighbourhood of Paris". This boat was designed by Comte de Lambert. This had 5 variable pitch fins on the hull beneath the water so inclined that when the boat begins to move "the boat rises and the planes come to the surface" with the result that "it skims over the surface with little but the propellers beneath the surface". The boat had twin hulls 18-foot long connected by a single deck 9-foot wide, and was fitted with a 14HP De Dion-Bouton motor, the boat was reported to have reached 20 mph. It was stated that "The boat running practically on its fins resembles an aeroplane". A March 1906 Scientific American article by American hydrofoil pioneer William E. Meacham explained the basic principle of hydrofoils. Alexander Graham Bell considered the invention of the hydroplane (now regarded as a distinct type, but also employing lift) a very significant achievement, and after reading the article began to sketch concepts of what is now called a hydrofoil boat. With his chief engineer Casey Baldwin, Bell began hydrofoil experiments in the summer of 1908. Baldwin studied the work of the Italian inventor Enrico Forlanini and began testing models based on those designs, which led to the development of hydrofoil watercraft. During Bell's world tour of 1910–1911, Bell and Baldwin met with Forlanini in Italy, where they rode in his hydrofoil boat over Lake Maggiore. Baldwin described it as being as smooth as flying. On returning to Bell's large laboratory at his Beinn Bhreagh estate near Baddeck, Nova Scotia, they experimented with a number of designs, culminating in Bell's HD-4. Using Renault engines, a top speed of was achieved, accelerating rapidly, taking waves without difficulty, steering well and showing good stability. Bell's report to the United States Navy permitted him to obtain two engines. On 9 September 1919 the HD-4 set a world marine speed record of , which stood for two decades. A full-scale replica of the HD-4 is viewable at the Alexander Graham Bell National Historic Site museum in Baddeck, Nova Scotia. In the early 1950s an English couple built the White Hawk, a jet-powered hydrofoil water craft, in an attempt to beat the absolute water speed record. However, in tests, White Hawk could barely top the record breaking speed of the 1919 HD-4. The designers had faced an engineering phenomenon that limits the top speed of even modern hydrofoils: cavitation disturbs the lift created by the foils as they move through the water at speed above , bending the lifting foil. First passenger boats German engineer Hanns von Schertel worked on hydrofoils prior to and during World War II in Germany. After the war, the Russians captured Schertel's team. As Germany was not authorized to build fast boats, Schertel went to Switzerland, where he established Together with his business partner and chief designer Karl Johann Büller the Supramar company. In 1952, Supramar launched the first commercial hydrofoil, PT10 "Freccia d'Oro" (Golden Arrow), in Lake Maggiore, between Switzerland and Italy. The PT10 is of surface-piercing type, it can carry 32 passengers and travel at . In 1968, the Bahraini born banker Hussain Najadi acquired the Supramar AG and expanded its operations into Japan, Hong Kong, Singapore, the UK, Norway and the US. General Dynamics of the United States became its licensee, and the Pentagon awarded its first R&D naval research project in the field of supercavitation. Hitachi Shipbuilding of Osaka, Japan, was another licensee of Supramar, as well as many leading ship owners and shipyards in the OECD countries. From 1952 to 1971, Supramar designed many models of hydrofoils: PT20, PT50, PT75, PT100 and PT150. All are of surface-piercing type, except the PT150 combining a surface-piercing foil forward with a fully submerged foil in the aft location. Over 200 of Supramar's design were built, most of them by Rodriquez (headed at the time by Engineer Carlo Rodriquez in Sicily, Italy. During the same period the Soviet Union experimented extensively with hydrofoils, constructing hydrofoil river boats and ferries with streamlined designs during the cold war period and into the 1980s. Such vessels include the Raketa (1957) type, followed by the larger Meteor type and the smaller Voskhod type. One of the most successful Soviet designer/inventor in this area was Rostislav Alexeyev, who some consider the 'father' of the modern hydrofoil due to his 1950s era high speed hydrofoil designs. Later, circa 1970s, Alexeyev combined his hydrofoil experience with the surface effect principle to create the Ekranoplan. Extensive investment in this type of technology in the USSR resulted in the largest civil hydrofoil fleet in the world and the making of the Meteor type, the most successful hydrofoil in history, with more than 400 units built. Peterhof hydrofoil (18272163540).jpg|Voskhod Meteor boat on Neva Bay.jpg|Meteor Raketa-185 on Khimki Reservoir 6-jun-2014 02.jpg|Raketa Polesye-1 (ship, 1986, Gomel, 7).jpg|Polesye Kizhi 06-2017 img30 Kometa-17 hydrofoil.jpg|Kometa In 1961, SRI International issued a study on "The Economic Feasibility of Passenger Hydrofoil Craft in US Domestic and Foreign Commerce". Commercial use of hydrofoils in the US first appeared in 1961 when two commuter vessels were commissioned by Harry Gale Nye, Jr.'s North American Hydrofoils to service the route from Atlantic Highlands, New Jersey to the financial district of Lower Manhattan. ==Military usage==

Germany A 17-ton German craft VS-6 Hydrofoil was designed and constructed in 1940, completed in 1941 for use as a mine layer; it was tested in the Baltic Sea, producing speeds of 47 knots. Tested against a standard E-boat over the next three years it performed well but was not brought into production. Being faster it could carry a higher payload and was capable of travelling over minefields but was prone to damage and noisier. Canada In Canada during World War II, Baldwin worked on an experimental smoke laying hydrofoil (later called the Comox Torpedo) that was later superseded by other smoke-laying technology and an experimental target-towing hydrofoil. The forward two foil assemblies of what is believed to be the latter hydrofoil were salvaged in the mid-1960s from a derelict hulk in Baddeck, Nova Scotia by Colin MacGregor Stevens. These were donated to the Maritime Museum in Halifax, Nova Scotia. The Canadian Armed Forces built and tested a number of hydrofoils (e.g., Baddeck and two vessels named ''Bras d'Or), which culminated in the high-speed anti-submarine hydrofoil HMCS Bras d'Or in the late 1960s. However, the program was cancelled in the early 1970s due to a shift away from anti-submarine warfare by the Canadian military. The Bras d'Or'' was a surface-piercing type that performed well during her trials, reaching a maximum speed of . Soviet Union patrol fast attack craft hydrofoil of the Cuban Navy. The USSR introduced several hydrofoil-based fast attack craft into their navy, principally: • Sarancha class missile boat, a unique vessel built in the 1970s • Turya class torpedo boat, introduced in 1972 and still in service • Matka class missile boat, introduced in the 1980s and still in service • Muravey class patrol boat, introduced in the 1980s and still in service • Project 664 United States , a military hydrofoil. The T-shaped foils are visible just below the water. The US Navy began experiments with hydrofoils in the mid-1950s by funding a sailing vessel that used hydrofoils to reach speeds in the 30 mph range. The XCH-4 (officially, Experimental Craft, Hydrofoil No. 4), designed by William P. Carl, exceeded speeds of and was mistaken for a seaplane due to its shape. Halobates was a 1957 US Navy prototype hydrofoil boat built by Miami Shipbuilding. The US Navy implemented a small number of combat hydrofoils, such as the Pegasus class, from 1977 through 1993. These hydrofoils were fast and well armed. Italy The Italian Navy used six hydrofoils of the Sparviero class starting in the late 1970s. These were armed with a 76 mm gun and two missiles, and were capable of speeds up to . Three similar boats were built for the Japan Maritime Self-Defense Force. ==Sailing and sports==

's AC72 at the 2013 America's Cup, San Francisco Bay. Several editions of the America's Cup have been raced with foiling yachts. The 2013 and 2017 editions used the AC72 and AC50 classes of catamaran respectively, and the 2021 edition used the AC75 class of foiling monohulls with canting arms. The French experimental sail-powered hydrofoil Hydroptère is the result of a research project that involves advanced engineering skills and technologies. In September 2009, the Hydroptère set new sailcraft world speed records in the 500 m category, with a speed of and in the category with a speed of . The 500 m speed record for sailboats is currently held by the Vestas Sailrocket, an exotic design which operates in effect as a hydrofoil. Another trimaran sailboat is the Windrider Rave. The Rave is a commercially available , two person, hydrofoil trimaran, capable of reaching speeds of . The boat was designed by Jim Brown. The Moth dinghy has evolved into some radical foil configurations. Hobie Sailboats produced a production foiling trimaran, the Hobie Trifoiler, the fastest production sailboat. Trifoilers have clocked speeds upward of thirty knots. A new kayak design, called Flyak, has hydrofoils that lift the kayak enough to significantly reduce drag, allowing speeds of up to . Some surfers have developed surfboards with hydrofoils called foilboards, specifically aimed at surfing big waves further out to sea. Quadrofoil Q2 is a two-seater, four-foiled hydrofoil electrical leisure watercraft. Its initial design was set in 2012 and it has been available commercially since the end of 2016. Powered by a 5.2-kWh lithium-ion battery pack and propelled by a 5.5 kW motor, it reaches the top speed of 40 km/h and has 80 km of range. The Manta5 Hydrofoiler XE-1 is a Hydrofoil E-bike, designed and built in New Zealand that has since been available commercially for pre-order since late 2017. Propelled by a 400 watt motor, it can reach speeds exceeding 14 km/h with a weight of 22 kg. A single charge of the battery lasts an hour for a rider weighing 85 kg. Candela, a Swedish company, is producing a recreational hydrofoil powerboat, making strong claims for efficiency, performance, and range. Hydrofoils are now widely used with kitesurfing, that is traction kites over water. Hydrofoils are a new trend in windsurfing - including the new Summer Olympic class, the IQFoil, and more recently with Wing foiling, which are essentially a kite with no strings, or a hand-held sail. on the North Sea Canal, the Netherlands 's Urzela JetFoil on West Lamma Channel, Hong Kong 's Barca Foilcat == Modern passenger boats ==

from Fethiye when the sister Kometas hydrofoil from Bodrum also arrived from Turkey in 2011. Soviet-built Voskhods are one of the most successful passenger hydrofoil designs. Manufactured in Soviet and later Ukrainian Crimea, they are in service in more than 20 countries. The most recent model, Voskhod-2M FFF, also known as Eurofoil, was built in Feodosiya for the Dutch public transport operator Connexxion. 's callsign, moored in Sevastopol Mid-2010s saw a Russian governmental program aimed at restoring passenger hydrofoil production. The , based on the earlier , Kolhida and Katran models, became the first to enter production, initially on factory in Rybinsk, and later on More shipyard in Feodosiya. Since 2018, the ships are running Sevastopol-Yalta and Sochi-Gelenzhik-Novorossiysk, with a Sevastopol-Sochi connection in the immediate plans in 2021. At the same time, the Alekseyev Bureau began building lighter, smaller hydrofoils, based on a widely successful model, at its own plant in Nizhny Novgorod, the relatively shallow-draft boats used on the Ob and the Volga. The , a development of the Meteor, became the Valday's larger sibling, the first ship launched in Nizhny Novgorod in August 2021. The Boeing 929 is widely used in Asia for passenger services, between Hong Kong and Macau and between the many islands of Japan. It was also used between Kyushu of Japan and Korean peninsula. Hong Kong ferry company TurboJET was the main user of Boeing 929. Current operation Current operators of hydrofoils include: • TurboJET service, which speeds passengers across the Pearl River Delta between Hong Kong and Macau in less than an hour, with an average speed of , mainly using Boeing's Jetfoil, until suspension of service due to COVID-19 pandemic. After the pandemic, all of the Boeing 929 are either scrapped or in dockyard. Currently only one Foilcat is in service and the remaining operating fleet are catamarans. Also serviced Shenzhen, Panyu (Nansha) and Kowloon. Operated by Shun Tak-China Travel Ship Management Limited. • Voskhod and Polesye service between Tulcea and Sulina on the Danube. • Meteor and Polesye service in Poland between Szczecin and Świnoujście. • Cometa service between Nizhneangarsk and Irkutsk on Lake Baikal. • Cometa service between Vladivostok and Slavyanka. • Polesye service between Mozyr and Turov on the Pripyat River (Belarus). • Meteor service between Saint Petersburg, Russia and the Peterhof Palace, a summer palace of Russian tsars. , Russia. , Greece. • Meteor service between Saint Petersburg, Russia and the Kronstadt, a strongly fortified Russian seaport town, located on Kotlin Island, near the head of the Gulf of Finland. It lies thirty kilometers west of Saint Petersburg. Since 2012 replaced by a catamaran Mercury. • Meteor, Raketa and Voskhod hydrofoil types operate all over Volga, Don and Kama Rivers in Russia. Also the Lena River and Amur River. • Meteor hydrofoils are operated by a number of tour operators in Croatia, mostly for packaged tours, but there are also some scheduled services to islands in Adriatic. • In Italy hydrofoils have been used for commercial connections since 1956, by the Rodriguez shipyards and the SNAV company. Currently (2025), the main hydrofoil operator in Italy is Liberty Lines, which operates connections between the smaller Sicilian islands (Aeolian Islands, Aegadian Islands, Pelagian Islands, Ustica and Pantelleria) with Sicily and Calabria, through the Strait of Messina (between Messina and Reggio Calabria) and between Trieste and Mali Lošinj (Croazia). SNAV operates connections between Naples and the smaller campanian islands and - in the summer period - between Naples and the Aeolian Islands. Hydrofoils are regularly operated on the three major Italian lakes by branches of the Ministry of Infrastructure and Transport: Navigazione Lago Maggiore services routes on Lake Maggiore between Locarno and Arona, Navigazione Lago di Como services routes on Lake Como, and Navigazione Lago di Garda services routes on Lake Garda. Three units of the Rodriguez RHS150 type operate on each lake, for a total of nine hydrofoils. At least until 2024, former Russian hydrofoils was used in southern Italy for connection with islands of Lazio and Campania by VETORaliscafi. SNAV had five RHS200, RHS160 and RHS150 used in the connections between Naples and the islands of Capri and Ischia, now mainly replaced by catamarans (the only hydrofoil left in the SNAV fleet, the RHS200 Super Jumbo, connect Naples and the Aeolian Islands in summer). • In July 2018, the new generation Kometa 120M boat has started operation on the busy Sevastopol-Yalta route in Crimea, with the plans to add two more and possible other routes in 2019. Discontinued operations • Until 31 December 2013, Fast Flying Ferries operated by Connexxion provided a regular public transport service over the North Sea Canal between Amsterdam Central Station and Velsen-Zuid in the Netherlands, using Voskhod 2M hydrofoils. It was stopped due to a new speed limit. • Between 1981 and 1990, Transmediterranea operated a service of hydrofoils connecting Ceuta and Algeciras in the Strait of Gibraltar. The crossing took half an hour, in comparison to the hour and a half of conventional ferries. Due to the common extreme winds and storms that take place in winter in the Strait of Gibraltar, the service was replaced in 1990 by catamarans, which were also able to carry cars. At the peak of the year, in summer, there was a service every half an hour in each direction. This high-speed connection had a big impact on the development of Ceuta, facilitating one-day business trips to mainland Spain. • Between 1964 and 1991 the Sydney hydrofoils operated on Sydney Harbour between Circular Quay and Manly. • Between 1969 and 1998 Red Funnel operated between Southampton and Cowes, Isle of Wight. • During the 1970s and 1980s there were frequent services between Belgrade and Tekija in Đerdap gorge. The distance of was covered in 3 hours and 30 minutes downstream and 4 hours upstream. • Between 1980 and 1981, B+I Line operated a Boeing 929 jetfoil, named Cú Na Mara (Hound of the Sea), between Liverpool and Dublin. The service was not successful and was discontinued at the end of the 1981 season. • Between the 1960s and 1985 there were hydrofoils going between Malmö, Sweden and Copenhagen, Denmark. They were retired and exchanged for catamarans. The service got cancelled when the Öresund Bridge got built in the early 2000s. • Condor Ferries operated six hydrofoil ferries over a 29-year period between the Channel Islands, the south coast of England and Saint-Malo in France. • Following the restoration of Estonian independence in the 1990s, the regular ferry service between Helsinki and Tallinn was augmented by Soviet built hydrofoils during the summer season in periods of good weather. The higher speed service competed with the traditional ro-ro ferries but allowed easy day trips for pedestrian travellers. They were ultimately replaced with high-speed catamarans that could also carry vehicles and have better seaworthiness; however, the latter ceased operations as the operator filed for bankruptcy in May 2018. == See also ==