Incandescent light bulb

's shop in Menlo Park Historians Robert Friedel and Paul Israel list inventors of incandescent lamps prior to Joseph Swan and Thomas Edison of General Electric. They conclude that Edison's version was the first practical implementation, able to outstrip the others because of a combination of four factors: an effective incandescent material; a vacuum higher than other implementations; a high resistance that made power distribution from a centralized source economically viable, and the development of the associated components required for a large-scale lighting system. However, Joseph Swan's incandescent light bulb pre-dated Edison's and was sufficiently practical that it was actually installed and in daily use in London in 1881. Historian Thomas Hughes has attributed Edison's business success to his development of an entire, integrated system of electric lighting. {{blockquote Early pre-commercial research In 1761, Ebenezer Kinnersley demonstrated heating a wire to incandescence. However such wires tended to melt or oxidize very rapidly (burn) in the presence of air. Limelight became a popular form of stage lighting in the early 19th century, by heating a piece of calcium oxide to incandescence with an oxyhydrogen torch. In 1802, Humphry Davy used what he described as "a battery of immense size", consisting of 2,000 cells housed in the basement of the Royal Institution of Great Britain, to create an incandescent light by passing the current through a thin strip of platinum, chosen because the metal had an extremely high melting point. It was not bright enough nor did it last long enough to be practical, but it was the precedent behind the efforts of scores of experimenters over the next 75 years. Davy also demonstrated the electric arc, by passing high current between two pieces of charcoal. For the next 40 years much research was given to turning the carbon arc lamp into a practical means of lighting. The carbon arc itself was dim and violet in color, emitting most of its energy in the ultraviolet, but the positive electrode was heated to just below the melting point of carbon and glowed very brightly with incandescence very close to that of sunlight. Arc lamps burned up their carbon rods very rapidly, expelled dangerous carbon monoxide, and tended to produce outputs in the tens of kilowatts. Therefore, they were only practical for lighting large areas, so researchers continued to search for a way to make lamps suitable for home use. Over the first three-quarters of the 19th century, many experimenters worked with various combinations of platinum or iridium wires, carbon rods, and evacuated or semi-evacuated enclosures. Many of these devices were demonstrated and some were patented. In 1838, Belgian lithographer Marcellin Jobard invented an incandescent light bulb with a vacuum atmosphere using a carbon filament. In 1840, British scientist Warren De la Rue enclosed a coiled platinum filament in a vacuum tube and passed an electric current through it. The design was based on the concept that the high melting point of platinum would allow it to operate at high temperatures and that the evacuated chamber would contain fewer gas molecules to react with the platinum, improving its longevity. Although a workable design, the cost of the platinum made it impractical for commercial use. In 1841, Frederick de Moleyns of England was granted the first patent for an incandescent lamp, with a design using platinum wires contained within a vacuum bulb. He also used carbon. In 1845, American John W. Starr patented an incandescent light bulb using carbon filaments. His invention was never produced commercially. In 1851, Jean Eugène Robert-Houdin publicly demonstrated incandescent light bulbs on his estate in Blois, France. His light bulbs are on display in the museum of the Château de Blois. In 1859, Moses G. Farmer built an electric incandescent light bulb using a platinum filament. Thomas Edison later saw one of these bulbs in a shop in Boston, Massachusetts, and asked Farmer for advice on the electric light business. on 1951 Soviet postal stamp In 1872, Russian Alexander Lodygin invented an incandescent light bulb and obtained a Russian patent in 1874. He used as a burner two carbon rods of diminished section in a glass receiver, hermetically sealed, and filled with nitrogen, electrically arranged so that the current could be passed to the second carbon when the first had been consumed. Later he lived in the US, changed his name to Alexander de Lodyguine and applied for and obtained patents for incandescent lamps having chromium, iridium, rhodium, ruthenium, osmium, molybdenum and tungsten filaments. On 24 July 1874, a Canadian patent was filed by Henry Woodward and Mathew Evans for a lamp consisting of carbon rods mounted in a nitrogen-filled glass cylinder. They were unsuccessful at commercializing their lamp, and sold rights to their patent to Thomas Edison in 1879. (Edison needed ownership of the novel claim of lamps connected in a parallel circuit.) The government of Canada maintains that it is Woodward and Evans who invented the lightbulb. Commercialization Carbon filament and vacuum Joseph Swan (1828–1914) was a British physicist and chemist. In 1850, he began working with carbonized paper filaments in an evacuated glass bulb. By 1860, he was able to demonstrate a working device but the lack of a good vacuum and an adequate supply of electricity resulted in a short lifetime for the bulb and an inefficient source of light. By the mid-1870s better pumps had become available, and Swan returned to his experiments. , the first house to be lit by electric lights With the help of Charles Stearn, an expert on vacuum pumps, in 1878, Swan developed a method of processing that avoided the early bulb blackening. This received a British Patent in 1880. On 18 December 1878, a lamp using a slender carbon rod was demonstrated at a meeting of the Newcastle Chemical Society though it only worked for a few minutes. Swan repeated the demonstration at another meeting on 17 January 1879 where it worked successfully. It was shown to 700 who attended a meeting of the Literary and Philosophical Society of Newcastle upon Tyne on 3 February 1879. In 1881, the Savoy Theatre in the City of Westminster, London was lit by Swan incandescent lightbulbs, which was the first theatre, and the first public building in the world, to be lit entirely by electricity. The first street in the world to be lit by incandescent lamps was Mosley Street, Newcastle upon Tyne, United Kingdom in 1880. with a light bulb from 1883. Thomas Edison began serious research into developing a practical incandescent lamp in 1878. Edison filed his first patent application for "Improvement in Electric Lights" on 14 October 1878. After many experiments, first with carbon in the early 1880s and then with platinum and other metals, in the end Edison returned to a carbon filament. The first successful test was on 22 October 1879, and lasted 13.5 hours. Edison continued to improve this design and by 4 November 1879, filed for a US patent for an electric lamp using "a carbon filament or strip coiled and connected ... to platina contact wires." Although the patent described several ways of creating the carbon filament including using "cotton and linen thread, wood splints, papers coiled in various ways," In 1880, the Oregon Railroad and Navigation Company steamer, Columbia, became the first application for Edison's incandescent electric lamps (it was also the first ship to use a dynamo). Albon Man, a New York lawyer, started Electro-Dynamic Light Company in 1878 to exploit his patents and those of William Sawyer. Weeks later the United States Electric Lighting Company was organized. This company made their first commercial installation of incandescent lamps in the fall of 1880, at the Mercantile Safe Deposit Company in New York City, about six months after the Edison incandescent lamps had been installed on the Columbia. Hiram S. Maxim was the chief engineer at the US Electric Lighting Company. After the great success in the United States, the incandescent light bulb patented by Edison also began to gain widespread popularity in Europe; among other places, the first Edison light bulbs in the Nordic countries were installed at the weaving hall of the Finlayson's textile factory in Tampere, Finland in March 1882. On 4 March 1880, just five months after Edison's light bulb, Alessandro Cruto developed a process to create thin carbon filaments by heating thin platinum filaments in the presence of gaseous ethyl alcohol to coat them with pure graphite, and then sublimating the platinum at high temperatures. In 1882 at the Munich Electrical Exhibition in Bavaria, Germany Cruto demonstrated bulbs that were more efficient than Edison's and produced a better, whiter light. Lewis Latimer, employed at the time by Edison, developed an improved method of heat-treating carbon filaments which reduced breakage and allowed them to be molded into novel shapes, such as the characteristic "M" shape of Maxim filaments. On 17 January 1882, Latimer received a patent for the "Process of Manufacturing Carbons", an improved method for the production of light bulb filaments, which was purchased by the United States Electric Light Company. Latimer patented other improvements such as a better way of attaching filaments to their wire supports. In Britain, the Edison and Swan companies merged into the Edison and Swan United Electric Company (later known as Ediswan, and ultimately incorporated into Thorn Lighting Limited). Edison was initially against this combination, but he was eventually forced to cooperate and the merger was made. Eventually, Edison acquired all of Swan's interest in the company. Swan sold his US patent rights to the Brush Electric Company in June 1882. for an improved electric lamp, 27 January 1880 The United States Patent Office issued a ruling 8 October 1883, that Edison's patents were based on the prior art of William Sawyer and were invalid. Litigation continued for a number of years. Eventually on 6 October 1889, a judge ruled that Edison's electric light improvement claim for "a filament of carbon of high resistance" was valid. In 1893, Heinrich Göbel claimed he had designed the first incandescent light bulb in 1854, with a thin carbonized bamboo filament of high resistance, platinum lead-in wires in an all-glass envelope, and a high vacuum. Judges of four courts raised doubts about the alleged Göbel anticipation, but there was never a decision in a final hearing due to the expiration of Edison's patent. Research work published in 2007 concluded that the story of the Göbel lamps in the 1850s is fictitious. The main difficulty with evacuating the lamps was moisture inside the bulb, which split when the lamp was lit, with resulting oxygen attacking the filament. In the 1880s, phosphoric anhydride was used in combination with expensive mercury vacuum pumps. However, about 1893, Italian inventor (1865–1939), who lacked these pumps, discovered that phosphorus vapours did the job of chemically binding the remaining amounts of water and oxygen. Twice as efficient as carbon filament lamps, Nernst lamps were briefly popular until overtaken by lamps using metal filaments. Metal filament, inert gas US575002A patent on 01.Dec.1897 to Alexander Lodyguine (Lodygin, Russia) describes filaments made of rare metals, amongst them was tungsten. Lodygin invented a process where rare metals such as tungsten can be chemically treated and heat-vaporized onto an electrically heated thread-like wire (platinum, carbon, gold) acting as a temporary base or skeletal form. (US patent 575,002). Lodygin later sold the patent rights to General Electric. In 1902, Siemens developed a tantalum lamp filament that was more efficient than even graphitized carbon filaments since they could operate at higher temperature. Since tantalum metal has a lower resistivity than carbon, the tantalum lamp filament was quite long and required multiple internal supports. The metal filament gradually shortened in use; the filaments were installed with large slack loops. Lamps used for several hundred hours became quite fragile. Metal filaments had the property of breaking and re-welding, though this would usually decrease resistance and shorten the life of the filament. General Electric bought the rights to use tantalum filaments and produced them in the US until 1913. From 1898 to around 1905, osmium was also used as a filament in lamps made by Carl Auer von Welsbach. The metal was so expensive that used lamps could be returned for partial credit. It could not be made for 110 V or 220 V so several lamps were wired in series for use on standard voltage circuits. These were primarily sold in Europe. Tungsten filament advertising of the Tungsram bulb from 1906. The inscription reads: wire lamp with a drawn wire – indestructible. On 13 December 1904, Hungarian Sándor Just and Croatian Franjo Hanaman were granted a Hungarian patent (No. 34541) for a tungsten filament lamp that lasted longer and gave brighter light than the carbon filament. Filling a bulb with an inert gas such as argon or nitrogen slows the evaporation of the tungsten filament compared to operating it in a vacuum. This allows for greater temperatures and therefore greater efficacy with less reduction in filament life. In 1906, William D. Coolidge developed a method of making "ductile tungsten" from sintered tungsten which could be made into filaments while working for General Electric Company. By 1911 General Electric had begun selling incandescent light bulbs with ductile tungsten wire. In 1913, Irving Langmuir found that filling a lamp with inert gas (nitrogen at first, and later argon) instead of a vacuum resulted in twice the luminous efficacy and reduced bulb blackening. He patented his device on April 18, 1916. image of a coiled coil tungsten filament In 1917, Burnie Lee Benbow was granted a patent for the coiled coil filament, in which a coiled filament is then itself wrapped into a coil by use of a mandrel. In 1921, Junichi Miura created the first double-coil bulb using a coiled coil tungsten filament while working for Hakunetsusha (a predecessor of Toshiba). At the time, machinery to mass-produce coiled coil filaments did not exist. Hakunetsusha developed a method to mass-produce coiled coil filaments by 1936. Between 1924 and the outbreak of the Second World War, the Phoebus cartel attempted to fix prices and sales quotas for bulb manufacturers outside of North America. In 1925, Marvin Pipkin, an American chemist, patented a process for frosting the inside of lamp bulbs without weakening them. In 1947, he patented a process for coating the inside of lamps with silica. In 1930, Hungarian Imre Bródy filled lamps with krypton gas rather than argon, and designed a process to obtain krypton from air. Production of krypton filled lamps based on his invention started at Ajka, Hungary in 1937, in a factory co-designed by Polányi and Hungarian-born physicist Egon Orowan. By 1964, improvements in efficiency and production of incandescent lamps had reduced the cost of providing a given quantity of light by a factor of thirty, compared with the cost at introduction of Edison's lighting system. Consumption of incandescent light bulbs grew rapidly in the US. In 1885, an estimated 300,000 general lighting service lamps were sold, all with carbon filaments. When tungsten filaments were introduced, about 50 million lamp sockets existed in the US. In 1914, 88.5 million lamps were used, (only 15% with carbon filaments), and by 1945, annual sales of lamps were 795 million (more than 5 lamps per person per year). ==Efficacy and efficiency==

light Less than 5% of the power consumed by a typical tungsten incandescent light bulb is converted into visible light, with most of the rest being emitted as invisible infrared radiation. Some applications make use of the emitted infrared radiation, such as heat lamps in incubators, lava lamps, Edison effect bulbs, and the Easy-Bake Oven toy. Quartz envelope halogen infrared heaters are used for industrial processes such as paint curing and space heating. Light bulbs are rated by their luminous efficacy, which is the ratio of the amount of visible light emitted (luminous flux) to the electrical power consumed. Luminous efficacy is measured in lumens per watt (lm/W). The luminous efficiency of a source is defined as the ratio of its luminous efficacy to the maximum possible luminous efficacy, which is 683 lm/W. An ideal white light source could produce about 250 lumens per watt, corresponding to a luminous efficiency of 37%. While heat from lights will reduce the need to run a building's heating system, the latter can usually produce the same amount of heat at lower cost than incandescent lights. The chart below lists the luminous efficacy and efficiency for several types of incandescent bulb. A longer chart in luminous efficacy compares a broader array of light sources. Color rendering The spectrum of light produced by an incandescent lamp closely approximates that of a black body radiator at the same temperature. The basis for light sources used as the standard for color perception is a tungsten incandescent lamp operating at a defined temperature. Light sources such as fluorescent lamps, high-intensity discharge lamps and LED lamps have higher luminous efficiency. These devices produce light by luminescence. Their light has bands of characteristic wavelengths, without the "tail" of invisible infrared emissions, instead of the continuous spectrum produced by a thermal source. By careful selection of fluorescent phosphor coatings or filters which modify the spectral distribution, the spectrum emitted can be tuned to mimic the appearance of incandescent sources, or other different color temperatures of white light. When used for tasks sensitive to color, such as motion picture lighting, these sources may require particular techniques to duplicate the appearance of incandescent lighting. Metamerism describes the effect of different light spectrum distributions on the perception of color. Cost of lighting The initial cost of an incandescent bulb is small compared to the cost of the energy it uses over its lifetime. Incandescent bulbs have a shorter life than most other lighting, an important factor if replacement is inconvenient or expensive. Some types of lamp, including incandescent and fluorescent, emit less light as they age; this may be an inconvenience, or may reduce effective lifetime due to lamp replacement before total failure. A comparison of incandescent lamp operating cost with other light sources must include illumination requirements, cost of the lamp and labor cost to replace lamps (taking into account effective lamp lifetime), cost of electricity used, effect of lamp operation on heating and air conditioning systems. When used for lighting in houses and commercial buildings, the energy lost to heat can significantly increase the energy required by a building's air conditioning system. During the heating season heat produced by the bulbs is not wasted, although in most cases it is more cost effective to obtain heat from the building's heating system. Regardless, over the course of a year a more efficient lighting system than incandescent saves energy in nearly all climates. Measures to ban Since incandescent light bulbs use more energy than alternatives such as compact fluorescent lamps (CFLs) and LED lamps, many governments have introduced measures to ban them by setting minimum efficacy standards higher than can be achieved by incandescent lamps. Measures to ban light bulbs have been implemented in the European Union, the United States, Russia, Brazil, Argentina, Canada and Australia, among others. The European Commission has calculated that the ban contributes to to the economy and saves 40 TWh of electricity every year, translating in emission reductions of . Objections to banning incandescent light bulbs include the higher initial cost of alternatives, lower quality of light of fluorescent lamps, and resistance to government regulation. Some people have concerns about the health effects of fluorescent lamps. A 2008 opinion by the European Commission's Scientific Committee on Emerging and Newly Identified Health Risks found that some of the compact florescent lamps available at the time emitted higher levels of UV and blue light than incandescent lamps, which might aggravate the symptoms of people with conditions that make them light sensitive. A 2017 review in the World Journal of Biological Psychiatry reported that blue-rich white LED lighting can suppress melatonin and disrupt sleep and circadian rhythms, with potential implications for mental illness. Efforts to improve efficacy with an E27 base, which can replace a non-halogen bulb Some research has been carried out to improve the efficacy of commercial incandescent lamps. In 2007, General Electric announced a high efficiency incandescent (HEI) lamp project, which they claimed would ultimately be as much as four times more efficient than current incandescents, although their initial production goal was to be approximately twice as efficient. The HEI program was terminated in 2008 due to slow progress. US Department of Energy research at Sandia National Laboratories initially indicated the potential for dramatically improved efficiency from a photonic lattice filament. Prompted by legislation in various countries mandating increased bulb efficiency, hybrid incandescent bulbs have been introduced by Philips. The Halogena Energy Saver incandescents can produce about 23 lm/W; about 30 percent more efficient than traditional incandescents, by using a reflective capsule to reflect formerly wasted infrared radiation back to the filament from which some is re-emitted as visible light. More advanced reflectors based on interference filters or photonic crystals can theoretically result in higher efficiency, up to a limit of about 270 lm/W (40% of the maximum efficacy possible). Laboratory proof-of-concept experiments have produced as much as 45 lm/W, approaching the efficacy of compact fluorescent bulbs which is still lower than LED bulbs. ==Construction==

Incandescent light bulbs consist of an air-tight glass enclosure (the envelope, or bulb) with a filament of tungsten wire inside the bulb, through which an electric current is passed. Contact wires and a base with two (or more) conductors provide electrical connections to the filament. Incandescent light bulbs usually contain a stem or glass mount anchored to the bulb's base that allows the electrical contacts to run through the envelope without air or gas leaks. Small wires embedded in the stem in turn support the filament and its lead wires. An electric current heats the filament to typically , well below tungsten's melting point of . Filament temperatures depend on the filament type, shape, size, and amount of current drawn. The heated filament emits light that approximates a continuous spectrum. The useful part of the emitted energy is visible light, but most energy is given off as heat in the near-infrared wavelengths. Bulbs Most light bulbs have either clear or coated glass. Coated glass bulbs have kaolin clay blown in and electrostatically deposited on the interior of the bulb. The powder layer diffuses the light from the filament. Pigments may be added to the clay to adjust the color of the light emitted. Kaolin diffused bulbs are used extensively in interior lighting because of their comparatively gentle light. Other kinds of colored bulbs are also made, including the various colors used for "party bulbs", Christmas tree lights and other decorative lighting. These are created by coloring the glass with a dopant; which is often a metal like cobalt (blue) or chromium (green). Neodymium-containing glass is sometimes used to provide a more natural-appearing light. The glass bulb of a general service lamp can reach temperatures between . Lamps intended for high power operation or used for heating purposes will have envelopes made of hard glass or fused quartz. The gas reduces evaporation of the filament, but the fill must be chosen carefully to avoid introducing significant heat losses. For these properties, chemical inertness and high atomic or molecular weight is desirable. The presence of gas keeps the tungsten below its vapor pressure, allowing it to be operated at higher temperature without reducing its life (or, for operating at the same temperature, prolongs the filament life). On the other hand, the presence of the gas leads to heat loss from the filament—and therefore efficiency loss due to reduced incandescence—by heat conduction and heat convection. Early lamps used only a vacuum to protect the filament from oxygen. The vacuum increases evaporation of the filament but eliminates two modes of heat loss. Some small modern lamps use vacuum as well. The most commonly used fills are: • Vacuum, used in small lamps. Provides best thermal insulation of the filament but does not protect against its evaporation. Used also in larger lamps where the outer bulb surface temperature has to be limited. • Argon (93%) and nitrogen (7%), where argon is used for its inertness, low thermal conductivity and low cost, and the nitrogen is added to increase the breakdown voltage and prevent arcing between parts of the filament. • Nitrogen, used in some higher-power lamps, e.g. projection lamps, and where higher breakdown voltage is needed due to proximity of filament parts or lead-in wires. • Krypton, which is more advantageous than argon due to its higher atomic weight and lower thermal conductivity (which also allows use of smaller bulbs), but its use is hindered by much higher cost, confining it mostly to smaller-size bulbs. • Krypton mixed with xenon, where xenon improves the gas properties further due to its higher atomic weight. Its use is however limited by its very high cost. The improvements by using xenon are modest in comparison to its cost. • Hydrogen, in special flashing lamps where rapid filament cooling is required; its high thermal conductivity is exploited here. • Halogen, a small amount mixed with inert gas which is used in halogen lamps, a distinct type of incandescent lamp. The gas fill must be free of traces of water, which greatly accelerates bulb blackening (see below). The gas layer close to the filament (called the Langmuir layer) is stagnant, with heat transfer occurring only by conduction. Only at some distance does convection occur to carry heat to the bulb's envelope. The orientation of the filament influences efficiency. Gas flow parallel to the filament, e.g., a vertically oriented bulb with vertical (or axial) filament, reduces convective losses. The efficiency of the lamp increases with a larger filament diameter. Thin-filament, low-power bulbs benefit less from a fill gas, so are often only evacuated. Early light bulbs with carbon filaments also used carbon monoxide, nitrogen, or mercury vapor. However, carbon filaments operate at lower temperatures than tungsten ones, so the effect of the fill gas was not significant as the heat losses offset any benefits. == Manufacturing ==

filament light bulb was the first one to have a metal filament. This one is from 1908. Early bulbs were laboriously assembled by hand. After automatic machinery was developed, the cost of bulbs fell. Until 1910, when Libbey's Westlake machine went into production, bulbs were generally produced by a team of three workers (two gatherers and a master gaffer) blowing the bulbs into wooden or cast-iron molds, coated with a paste. Around 150 bulbs per hour were produced by the hand-blowing process in the 1880s at Corning Glass Works. The Ribbon Machine surpassed any previous attempts to automate bulb production and was used to produce incandescent bulbs into the 21st century. The inventor, William Woods, along with his colleague at Corning Glass Works, David E. Gray, had created a machine that by 1939 was producing 1,000 bulbs per minute. By the 1970s, 15 ribbon machines installed in factories around the world produced the entire supply of incandescent bulbs. The filament and its supports are assembled on a glass stem, which is then fused to the bulb. The air is pumped out of the bulb, and the evacuation tube in the stem press is sealed by a flame. The bulb is then inserted into the lamp base, and the whole assembly tested. The 2016 closing of Osram-Sylvania's Wellsboro, Pennsylvania plant meant that one of the last remaining ribbon machines in the United States was shut down. ==Filament==

Carbon has the highest melting point of any element, and in carbon arc lamps it had been demonstrated to produce incandescence fairly close to that of sunlight. However, carbon has a tendency to sublimate before reaching its melting point depending on pressure, which led to rapid blackening of vacuumed bulbs. The first commercially successful light bulb filaments were made from carbonized paper or bamboo. Carbon filaments have a negative temperature coefficient of resistance—as they get hotter, their electrical resistance decreases. This made the lamp sensitive to fluctuations in the power supply, since a small increase of voltage would cause the filament to heat up, reducing its resistance and causing it to draw even more power and heat even further. Carbon filaments were "flashed" by heating in a hydrocarbon vapor (usually gasoline), to improve their strength and uniformity. Metallized or "graphitized" filaments were first heated to high temperature to transform them into graphite, which further strengthened and smoothed the filament. These filaments have a positive temperature coefficient, like a metallic conductor, which stabilized the lamps operating properties against minor variations in supply voltage. Metal filaments were tried in 1897 and started to displace carbon starting around 1904. Tungsten has the highest available melting point, but brittleness was an obstacle. By 1910, a process was developed by William D. Coolidge at General Electric for production of a ductile form of tungsten. The process required pressing tungsten powder into bars, then several steps of sintering, swaging, and then wire drawing. It was found that very pure tungsten formed filaments that sagged in use, and that a very small "doping" treatment with potassium, silicon, and aluminum oxides at the level of a few hundred parts per million (so-called AKS tungsten) greatly improved the life and durability of the tungsten filaments. The predominant mechanism for failure in tungsten filaments even now is grain boundary sliding accommodated by diffusional creep. During operation, the tungsten wire is stressed under the load of its own weight and because of the diffusion that can occur at high temperatures, grains begin to rotate and slide. This stress, because of variations in the filament, causes the filament to sag nonuniformly, which ultimately introduces further torque on the filament. or sometimes krypton. While inert gas reduces filament evaporation, it also conducts heat from the filament, thereby cooling the filament and reducing efficiency. At constant pressure and temperature, the thermal conductivity of a gas depends upon the molecular weight of the gas and the cross sectional area of the gas molecules. Higher molecular weight gases have lower thermal conductivity, because both the molecular weight and cross sectional area are higher. Xenon gas improves efficiency because of its high molecular weight, but is also more expensive, so its use is limited to smaller lamps. Filament notching is due to uneven evaporation of the filament. Small variations in resistivity along the filament cause "hot spots" to form at points of higher resistivity; Since a filament breaking in a gas-filled bulb can form an electric arc, which may spread between the terminals and draw very heavy current, intentionally thin lead-in wires or more elaborate protection devices are therefore often used as fuses built into the light bulb. More nitrogen is used in higher-voltage lamps to reduce the possibility of arcing. A very small amount of water vapor inside a light bulb can significantly increase lamp darkening. Water vapor dissociates into hydrogen and oxygen at the hot filament. The oxygen attacks the tungsten metal, and the resulting tungsten oxide particles travel to cooler parts of the lamp. Hydrogen from water vapor reduces the oxide, reforming water vapor and continuing this water cycle. Some old, high-powered lamps used in theater, projection, searchlight, and lighthouse service with heavy, sturdy filaments contained loose tungsten powder within the envelope. From time to time, the operator would remove the bulb and shake it, allowing the tungsten powder to scrub off most of the tungsten that had condensed on the interior of the envelope, removing the blackening and brightening the lamp again. Halogen lamps . The two ring-shaped structures left and right are filament supports. The halogen lamp reduces uneven evaporation of the filament and eliminates darkening of the envelope by filling the lamp with a halogen gas at low pressure, along with an inert gas. The halogen cycle increases the lifetime of the bulb and prevents its darkening by redepositing tungsten from the inside of the bulb back onto the filament. The halogen lamp can operate its filament at a higher temperature than a standard gas filled lamp of similar power without loss of operating life. Such bulbs are much smaller than normal incandescent bulbs, and are widely used where intense illumination is needed in a limited space. Fiber-optic lamps for optical microscopy is one typical application. Incandescent arc lamps A variation of the incandescent lamp did not use a hot wire filament, but instead used an arc struck on a spherical bead electrode to produce heat. The electrode then became incandescent, with the arc contributing little to the light produced. Such lamps were used for projection or illumination for scientific instruments such as microscopes. These arc lamps ran on relatively low voltages and incorporated tungsten filaments to start ionization within the envelope. They provided the intense concentrated light of an arc lamp but were easier to operate. Developed around 1915, these lamps were displaced by mercury and xenon arc lamps. ==Electrical characteristics==

Power Incandescent lamps are nearly pure resistive loads with a power factor of 1. Unlike discharge lamps or LED lamps, the power consumed is equal to the apparent power in the circuit. Incandescent light bulbs are usually marketed according to the electrical power consumed. This depends mainly on the operating resistance of the filament. For two bulbs of the same voltage, and type, the higher-powered bulb gives more light. The table shows the approximate typical output, in lumens, of standard 120 volt incandescent light bulbs at various powers. Light output of similar 230 V bulbs is usually slightly less, even though in this table the opposite holds true at 25 W. The lower current (higher voltage) filament is thinner and has to be operated at a slightly lower temperature for the same life expectancy, which reduces energy efficiency. The lumen values for "soft white" bulbs will generally be slightly lower than for clear bulbs at the same power. Current and resistance The resistance of the filament is temperature dependent. The cold resistance of tungsten-filament lamps is about the resistance when operating. For example, a 100-watt, 120-volt lamp has a resistance of 144 ohms when lit, but the cold resistance is much lower (about 9.5 ohms). Since incandescent lamps are resistive loads, simple phase-control TRIAC dimmers can be used to control brightness. Electrical contacts may carry a "T" rating symbol indicating that they are designed to control circuits with the high inrush current characteristic of tungsten lamps. For a 100-watt, 120-volt general-service lamp, the current stabilizes in about 0.10 seconds, and the lamp reaches 90% of its full brightness after about 0.13 seconds. ==Physical characteristics==

Safety The filament in a tungsten light bulb is not easy to break when the bulb is cold, but filaments are more vulnerable when they are hot because the incandescent metal is less rigid. An impact on the outside of the bulb may cause the filament to break or experience a surge in electric current that causes part of it to melt or vaporize. In most modern incandescent bulbs, part of the wire inside the bulb acts like a fuse: if a broken filament produces an electrical short inside the bulb, the fusible section of wire will melt and cut the current off to prevent damage to the supply lines. A hot glass bulb may fracture on contact with cold objects. When the glass envelope breaks, the bulb implodes, exposing the filament to ambient air. The air then usually destroys the hot filament through oxidation. Bulb shapes Bulb shape and size designations are given in national standards. Some designations are one or more letters followed by one or more numbers, e.g. A55 or PAR38, where the letters identify the shape and the numbers some characteristic size. National standards such as ANSI C79.1-2002, IS 14897:2000 and JIS C 7710:1988 cover a common terminology for bulb shapes. Common shape codes ;General Service/General Lighting Service (GLS) :Light emitted in (nearly) all directions. Available either clear or frosted. :Types: General (A), elliptical (E), mushroom (M), sign (S), tubular (T) :120 V sizes: A17, 19 and 21 :230 V sizes: A55 and 60 ;High Wattage General Service :Lamps greater than 200 watts. :Types: Pear-shaped (PS) ;Decorative :lamps used in chandeliers, etc. Smaller candle-sized bulbs may use a smaller socket. :Types: candle (B), twisted candle, bent-tip candle (CA & BA), flame (F), globe (G), lantern chimney (H), fancy round (P) :230 V sizes: P45, G95 ;Reflector (R): Reflective coating inside the bulb directs light forward. Flood types (FL) spread light. Spot types (SP) concentrate the light. Reflector (R) bulbs put approximately double the amount of light (foot-candles) on the front central area as General Service (A) of same wattage. :Types: Standard reflector (R), bulged reflector (BR), elliptical reflector (ER), crown-silvered :120 V sizes: R16, 20, 25 and 30 :230 V sizes: R50, 63, 80 and 95 ;Parabolic aluminized reflector (PAR) :Parabolic aluminized reflector (PAR) bulbs control light more precisely. They produce about four times the concentrated light intensity of general service (A), and are used in recessed and track lighting. Weatherproof casings are available for outdoor spot and flood fixtures. :120 V sizes: PAR 16, 20, 30, 38, 56 and 64 :230 V sizes: PAR 16, 20, 30, 38, 56 and 64 :Available in numerous spot and flood beam spreads. Like all light bulbs, the number represents the diameter of the bulb in of an inch. Therefore, a PAR 16 is in diameter, a PAR 20 is in diameter, PAR 30 is and a PAR 38 is in diameter. ;Multifaceted reflector (MR) :Multifaceted reflector bulbs are usually smaller in size and run at a lower voltage, often 12 V. ;HIR/IRC: "HIR" is a GE designation for a lamp with an infrared reflective coating. Since less heat escapes, the filament burns hotter and more efficiently. The Osram designation for a similar coating is "IRC". Lamp bases Large lamps may have a screw base or a bayonet base, with one or more contacts on the base. The shell may serve as an electrical contact or only as a mechanical support. Bayonet base lamps are frequently used in automotive lamps to resist loosening by vibration. Some tubular lamps have an electrical contact at either end. Miniature lamps may have a wedge base and wire contacts, and some automotive and special purpose lamps have screw terminals for connection to wires. Very small lamps may have the filament support wires extended through the base of the lamp for connections. A bipin base is often used for halogen or reflector lamps. In the late 19th century, manufacturers introduced a multitude of incompatible lamp bases. General Electric's "Mazda" standard base sizes were soon adopted across the US. Lamp bases may be secured to the bulb with a cement, or by mechanical crimping to indentations molded into the glass bulb. Lamps intended for use in optical systems have bases with alignment features so that the filament is positioned accurately within the optical system. A screw-base lamp may have a random orientation of the filament when the lamp is installed in the socket. Contacts in the lightbulb socket allow the electric current to pass through the base to the filament. The socket provides electrical connections and mechanical support, and allows changing the lamp when it burns out. ==Light output and lifetime==

Incandescent lamps are very sensitive to changes in the supply voltage. These characteristics are of great practical and economic importance. For a supply voltage V near the rated voltage of the lamp: • Light output is approximately proportional to V 3.4 • Power consumption is approximately proportional to V 1.6 • Lifetime is approximately proportional to V −16 • Color temperature is approximately proportional to V 0.42 A 5% reduction in voltage will double the life of the bulb, but reduce its light output by about 16%. Long-life bulbs take advantage of this trade-off in applications such as traffic signal lamps. Since electric energy they use costs more than the cost of the bulb, general service lamps emphasize efficiency over long operating life. The objective is to minimize the cost of light, not the cost of lamps. When this was exposed in 1953, General Electric and other leading American manufacturers were banned from limiting the life. The relationships above are valid for only a few percent change of voltage around standard rated conditions, but they indicate that a lamp operated at low voltage could last much longer than at rated voltage, albeit with greatly reduced light output. The "Centennial Light" is a light bulb that is accepted by the Guinness Book of World Records as having been burning almost continuously at a fire station in Livermore, California, since 1901. However, the bulb emits the equivalent light of a four watt bulb. A similar story can be told of a 40-watt bulb in Texas that has been illuminated since 21 September 1908. It once resided in an opera house where notable celebrities stopped to take in its glow, and was moved to an area museum in 1977. Photoflood lamps used for photographic lighting favor light output over life, with some lasting only two hours. The upper temperature limit for the filament is the melting point of the metal. Tungsten is the metal with the highest melting point, . A 50-hour-life projection bulb, for instance, is designed to operate only below that melting point. Such a lamp may achieve up to 22 lumens per watt, compared with 17.5 for a 750-hour general service lamp. Lamps of the same power rating but designed for different voltages have different luminous efficacy. For example, a 100-watt, 1000 hour, 120-volt lamp will produce about 17.1 lumens per watt. A similar lamp designed for 230 V would produce only around 12.8 lumens per watt, and one designed for 30 volts (train lighting) would produce as much as 19.8 lumens per watt. Lower voltage lamps have a thicker filament, for the same power rating. They can run hotter for the same lifetime before the filament evaporates. The wires used to support the filament make it mechanically stronger, but remove heat, creating another tradeoff between efficiency and long life. Many general-service 120-volt lamps use no additional support wires, but lamps designed for "rough service" or "vibration service" may have as many as five. Low-voltage lamps have filaments made of heavier wire and do not require additional support wires. Very low voltages are inefficient since the lead wires would conduct too much heat away from the filament, so the practical lower limit for incandescent lamps is 1.5 volts. Very long filaments for high voltages are fragile, and lamp bases become more difficult to insulate, so lamps for illumination are not made with rated voltages over 300 volts. Some infrared heating elements are made for higher voltages, but these use tubular bulbs with widely separated terminals. File:Livermore Centennial Light Bulb.jpg|The Centennial Light is the longest-lasting light bulb in the world. File:Various lighting spectrums - Flurescent incandescent diode and candle.jpg|Various lighting spectra as viewed in a diffraction grating. Upper left: fluorescent lamp, upper right: incandescent bulb, lower left: white LED, lower right: candle flame. ==See also==