Geologic history During the Lower
Cretaceous (~150–100 Ma)
Rangitata Orogeny, an accretionary wedge accumulated and was uplifted on the margin of
Gondwana in present-day New Zealand. The resulting topography was eroded throughout the Cretaceous. After the Rangitata Orogeny, seafloor spreading commenced during the Middle Cretaceous. This resulted in the formation of the
Tasman Sea as New Zealand separated from
Australia. Normal faults, including the Manaia Fault, formed as the Taranaki Basin developed during
seafloor spreading. Rifting continued until the
Eocene (~56 Ma), when the Taranaki Basin underwent passive subsidence. Kapuni collected abundant organic material under coastal plain and fluvio-estuarine environments during much of the Eocene. A broad
marine transgression occurred in the Late
Oligocene to Early
Miocene (~28–20 Ma), and mudstones were deposited on top of the Eocene organic-rich shales and sandstones. Cenozoic compression in the Taranaki Basin has generally been attributed to a change in stress regime caused by the development of the
Hikurangi Subduction System between the Pacific and Australian Plates off the east coast of New Zealand's North Island. Late Eocene compressional structures in the Taranaki Basin correspond with a period of elevated uplift rates along the
Alpine Fault on New Zealand's
South Island that has also been attributed to the nearby subduction zone. Kapuni is located on the Australian Plate, west of the plate boundary zone and above the subducting Pacific Plate.
Source Rocks Kapuni's source rocks are a series of type III
kerogen-rich coal sequences in the Eocene (~56–34 Ma) Mangahewa Formation of the Kapuni Group. These coals were deposited under coastal plain and fluo-estuarine environments and reach up to 10 m in thickness.
Reservoirs Like its source rocks, Kapuni's reservoir layers are located in the Eocene Mangahewa Formation and were deposited as part of a general transgressive sequence. The reservoirs are predominantly sandstones, shales, and coals deposited in shore, fluvial, and estuarine environments. Kapuni's reservoirs are located below a depth of 3000 m. They range in average thickness from 20 m to 130 m, average natural-gas fraction from 0.06 to 0.95, and average porosity from 12.2% to 16.8% by volume.
Kapuni Anticline Hydrocarbons of the Kapuni Field are trapped by the Kapuni Anticline, in the hanging wall of the east-dipping Manaia Fault, a reverse fault in the Eastern Mobile Belt. The Kapuni Anticline is asymmetric, doubly-plunging, and approximately 18 km long and 8 km wide. The Manaia Fault initially developed as a normal fault bounding the Manaia Graben during Cretaceous to Early Eocene rifting associated with the opening of the Tasman Sea. Dextral transpression associated with the Hikurangi Subduction System caused fault reactivation and basin inversion during the Eocene and Miocene, resulting in the development of the Kapuni Anticline. Maximum throw on the Manaia Fault is 900 m.
Seal Middle Oligocene (~30–25 Ma) mudstones of the Otaraoa Formation overly the Mangahewa Formation, sealing Kapuni's reservoirs. These mudstones were deposited under a continental shelf environment as part of the same broad transgressive sequence under which the Mangahewa Formation was deposited.
Faulting Faulting is pervasive in the Kapuni Group and predominantly consists of southwest–northeast right-lateral and northwest–southeast left-lateral strike-slip faults. These faults were formed under transpressional and compressional stress regimes during the Late Eocene to Late Miocene and are indicative of an east–west direction of maximum compressive stress. In the northern portion of the Kapuni Anticline, these two dominant fault trends become nearly orthogonal to one another. This is a result of fault block rotation that produced necessary extension along the anticline's younger units during fold growth.
Secondary porosity Kapuni's gas is CO2-rich, containing approximately 40-45 mol% CO2. This has facilitated significant diagenesis and the development of secondary porosity, especially in the K3E reservoir, one of the field's main producing reservoirs. Beginning approximately 5 Ma, thermal maturation of source rocks expelled CO2, which dissolved into groundwater. The acidic groundwater migrated updip towards the crest of the Kapuni anticline, dissolving feldspar and carbonates along its route. Intervals of coarser clasts experienced net dissolution, while finer-grained intervals experienced precipitation of authigenic clays, carbonates, and quartz. Precipitation of quartz and carbonate cements began approximately 4 Ma at temperatures exceeding 100
°C. The carbon isotope signature of carbonate cements in the K3E reservoir suggests an intraformational origin. As a result of diagenesis, the K3E reservoir contains areas exhibiting significant secondary porosity and enhanced reservoir quality along with tight, cemented regions of poor reservoir quality. == Production history ==