Digital signal

The term digital signal has related definitions in different contexts. In digital electronics digital signal In digital electronics, a digital signal is a pulse amplitude modulated signal, i.e., a sequence of fixed-width electrical pulses or light pulses, each occupying one of a discrete number of levels of amplitude. A special case is a logic signal or a binary signal, which varies between a low and a high signal level. The pulse trains in digital circuits are typically generated by metal–oxide–semiconductor field-effect transistor (MOSFET) devices, due to their rapid on–off electronic switching speed and large-scale integration (LSI) capability. In contrast, bipolar junction transistors more slowly generate signals resembling sine waves. The digital signal may be stored, processed or transmitted physically as a pulse-code modulation (PCM) signal. In communications (FSK) signal is alternating between two waveforms and allows passband transmission. It is considered a means of digital data transmission. digital signal used in baseband transmission (line coding) In digital communications, a digital signal is a continuous-time physical signal, alternating between a discrete number of waveforms, representing a bitstream. The shape of the waveform depends on the transmission scheme, which may be either a line coding scheme allowing baseband transmission; or a digital modulation scheme, allowing passband transmission over long wires or over a limited radio frequency band. Such a carrier-modulated sine wave is considered a digital signal in literature on digital communications and data transmission, but considered as a bit stream converted to an analog signal in specific cases where the signal will be carried over a system meant for analog communication, such as an analog telephone line. In communications, sources of interference are usually present, and noise is frequently a significant problem. The effects of interference are typically minimized by filtering off interfering signals as much as possible and by using data redundancy. The main advantages of digital signals for communications are often considered to be noise immunity, and the ability, in many cases such as with audio and video data, to use data compression to greatly decrease the bandwidth that is required on the communication media. ==Logic voltage levels==

A waveform that switches representing the two states of a Boolean value (0 and 1, or low and high, or false and true) is referred to as a digital signal or logic signal or binary signal when it is interpreted in terms of only two possible digits. The two states are usually represented by some measurement of an electrical property: Voltage is the most common, but current is used in some logic families. Two ranges of voltages are typically defined for each logic family, which are frequently not directly adjacent. The signal is low when in the low range and high when in the high range, and in between the two ranges the behavior can vary between different types of gates. The clock signal is a special digital signal that is used to synchronize many digital circuits. The image shown can be considered the waveform of a clock signal. Logic changes are triggered either by the rising edge or the falling edge. The rising edge is the transition from a low voltage (level 1 in the diagram) to a high voltage (level 2). The falling edge is the transition from a high voltage to a low one. Although in a highly simplified and idealized model of a digital circuit, we may wish for these transitions to occur instantaneously, no real-world circuit is purely resistive, and therefore no circuit can instantly change voltage levels. This means that during a short, finite transition time, the output may not properly reflect the input, and will not correspond to either a logically high or low voltage. ==Modulation==

To create a digital signal, a signal must be modulated with a control signal to produce it. The simplest modulation, a type of unipolar encoding, is simply to switch on and off a DC signal so that high voltages represent a '1' and low voltages are '0'. In digital radio schemes, one or more carrier waves are amplitude, frequency or phase modulated by the control signal to produce a digital signal suitable for transmission. Asymmetric Digital Subscriber Line (ADSL) over telephone wires, does not primarily use binary logic; the digital signals for individual carriers are modulated with different-valued logics, depending on the Shannon capacity of the individual channel. ==Clocking==

Digital signals may be sampled by a clock signal at regular intervals by passing the signal through a flip-flop. When this is done, the input is measured at the clock edge and the signal from that time. The signal is then held steady until the next clock. This process is the basis of synchronous logic. Asynchronous logic also exists, which uses no single clock, and generally operates more quickly, and may use less power, but is significantly harder to design. == See also ==