Skew lines

If four points are chosen at random uniformly within a unit cube, they will almost surely define a pair of skew lines. After the first three points have been chosen, the fourth point will define a non-skew line if, and only if, it is coplanar with the first three points. However, the plane through the first three points forms a subset of measure zero of the cube, and the probability that the fourth point lies on this plane is zero. If it does not, the lines defined by the points will be skew. Similarly, in three-dimensional space a very small perturbation of any two parallel or intersecting lines will almost certainly turn them into skew lines. Therefore, any four points in general position always form skew lines. In this sense, skew lines are the "usual" case, and parallel or intersecting lines are special cases. ==Formulas==

Testing for skewness If each line in a pair of skew lines is defined by two points that it passes through, then these four points must not be coplanar, so they must be the vertices of a tetrahedron of nonzero volume. Conversely, any two pairs of points defining a tetrahedron of nonzero volume also define a pair of skew lines. Therefore, a test of whether two pairs of points define skew lines is to apply the formula for the volume of a tetrahedron in terms of its four vertices. Denoting one point as the 1×3 vector whose three elements are the point's three coordinate values, and likewise denoting , , and for the other points, we can check if the line through and is skew to the line through and by seeing if the tetrahedron volume formula gives a non-zero result: :V=\frac{1}{6}\left|\det\left[\begin{matrix}\mathbf{a}-\mathbf{b} \\ \mathbf{b}-\mathbf{c} \\ \mathbf{c}-\mathbf{d} \end{matrix}\right]\right|. Nearest points Expressing the two lines as vectors: :\text{Line 1:} \; \mathbf{v_1}=\mathbf{p_1}+t_1\mathbf{d_1} :\text{Line 2:} \; \mathbf{v_2}=\mathbf{p_2}+t_2\mathbf{d_2} The cross product of \mathbf{d_1} and \mathbf{d_2} is perpendicular to the lines. : \mathbf{n}= \mathbf{d_1} \times \mathbf{d_2} The plane formed by the translations of Line 2 along \mathbf{n} contains the point \mathbf{p_2} and is perpendicular to \mathbf{n_2}= \mathbf{d_2} \times \mathbf{n}. Therefore, the intersecting point of Line 1 with the above-mentioned plane, which is also the point on Line 1 that is nearest to Line 2 is given by : \mathbf{c_1}=\mathbf{p_1}+ \frac{(\mathbf{p_2}-\mathbf{p_1})\cdot\mathbf{n_2}}{\mathbf{d_1}\cdot\mathbf{n_2}} \mathbf{d_1} Similarly, the point on Line 2 nearest to Line 1 is given by (where \mathbf{n_1}= \mathbf{d_1} \times \mathbf{n} ) : \mathbf{c_2}=\mathbf{p_2}+ \frac{(\mathbf{p_1}-\mathbf{p_2})\cdot\mathbf{n_1}}{\mathbf{d_2}\cdot\mathbf{n_1}} \mathbf{d_2} Distance The nearest points \mathbf{c_1} and \mathbf{c_2} form the shortest line segment joining Line 1 and Line 2: : d = \Vert \mathbf{c_1} - \mathbf{c_2} \Vert. The distance between nearest points in two skew lines may also be expressed using other vectors: : \mathbf{x} = \mathbf{a} + \lambda \mathbf{b}; : \mathbf{y} = \mathbf{c} + \mu \mathbf{d}. Here the 1×3 vector represents an arbitrary point on the line through particular point with representing the direction of the line and with the value of the real number \lambda determining where the point is on the line, and similarly for arbitrary point on the line through particular point in direction . The cross product of b and d is perpendicular to the lines, as is the unit vector : \mathbf{n} = \frac{\mathbf{b} \times \mathbf{d}} The perpendicular distance between the lines is then : d = |\mathbf{n} \cdot (\mathbf{c} - \mathbf{a})|. (if |b × d| is zero the lines are parallel and this method cannot be used). ==More than two lines==

Configurations A configuration of skew lines is a set of lines in which all pairs are skew. Two configurations are said to be isotopic if it is possible to continuously transform one configuration into the other, maintaining throughout the transformation the invariant that all pairs of lines remain skew. Any two configurations of two lines are easily seen to be isotopic, and configurations of the same number of lines in dimensions higher than three are always isotopic, but there exist multiple non-isotopic configurations of three or more lines in three dimensions. The number of nonisotopic configurations of n lines in R3, starting at n = 1, is :1, 1, 2, 3, 7, 19, 74, ... . Ruled surfaces of projective space by skew lines on nested hyperboloids. If one rotates a line L around another line M skew but not perpendicular to it, the surface of revolution swept out by L is a hyperboloid of one sheet. For instance, the three hyperboloids visible in the illustration can be formed in this way by rotating a line L around the central white vertical line M. The copies of L within this surface form a regulus; the hyperboloid also contains a second family of lines that are also skew to M at the same distance as L from it but with the opposite angle that form the opposite regulus. The two reguli display the hyperboloid as a ruled surface. An affine transformation of this ruled surface produces a surface which in general has an elliptical cross-section rather than the circular cross-section produced by rotating L around L'; such surfaces are also called hyperboloids of one sheet, and again are ruled by two families of mutually skew lines. A third type of ruled surface is the hyperbolic paraboloid. Like the hyperboloid of one sheet, the hyperbolic paraboloid has two families of skew lines; in each of the two families the lines are parallel to a common plane although not to each other. Any three skew lines in R3 lie on exactly one ruled surface of one of these types. Gallucci's theorem If three skew lines all meet three other skew lines, any transversal of the first set of three meets any transversal of the second set. == Skew flats in higher dimensions ==

In higher-dimensional space, a flat of dimension k is referred to as a k-flat. Thus, a line may also be called a 1-flat. Generalizing the concept of skew lines to d-dimensional space, an i-flat and a j-flat may be skew if . As with lines in 3-space, skew flats are those that are neither parallel nor intersect. In affine d-space, two flats of any dimension may be parallel. However, in projective space, parallelism does not exist; two flats must either intersect or be skew. Let be the set of points on an i-flat, and let be the set of points on a j-flat. In projective d-space, if then the intersection of and must contain a (i+j−d)-flat. (A 0-flat is a point.) In either geometry, if and intersect at a k-flat, for , then the points of determine a (i+j−k)-flat. ==See also==