Solar panel

Early developments In 1839, the ability of some materials to create an electrical charge from light exposure was first observed by the French physicist Edmond Becquerel. Though these initial solar cells were too inefficient for even simple electric devices, they were used as an instrument to measure light. The observation by Becquerel was not replicated again until 1873, when the English electrical engineer Willoughby Smith discovered that the charge could be caused by light hitting selenium. After this discovery, William Grylls Adams and Richard Evans Day published "The action of light on selenium" in 1876, describing the experiment they used to replicate Smith's results. In 1881, the American inventor Charles Fritts created the first commercial solar cell, which was reported by Fritts as "continuous, constant and of considerable force not only by exposure to sunlight but also to dim, diffused daylight". However, these solar cells were still very inefficient for practical power production, especially compared to coal-fired power plants. In 1939, Russell Ohl created the solar cell design that is used in many modern solar panels. He patented his design in 1941. In 1954, this design was first used by Bell Labs to create the first commercially viable silicon solar cell. Solar panel installers saw significant growth between 2008 and 2013. Due to that growth many installers had projects that were not "ideal" solar roof tops to work with and had to find solutions to shaded roofs and orientation difficulties. This challenge was initially addressed by the re-popularization of micro-inverters and later the invention of power optimizers. Solar panel manufacturers partnered with micro-inverter companies to create alternating current modules and power optimizer companies partnered with module manufacturers to create smart modules. In 2013 many solar panel manufacturers announced and began shipping their smart module solutions. Between 1992 and 2023, the worldwide usage of photovoltaics (PV) increased exponentially. During this period, it evolved from a niche market of small-scale applications to a mainstream electricity source. From 2016 to 2022, PV has seen an annual capacity and production growth rate of around 26%, doubling approximately every three years. By the end of 2022, the global cumulative installed PV capacity reached about 1,185 gigawatts (GW), supplying over 6% of global electricity demand, up from about 3% in 2019. The decreasing cost of solar panels is driving an increase in solar energy use in the Global South. Many countries in the Global South rely on expensive fossil fuel imports. Many homes and businesses are switching to solar energy to save money == Theory and construction ==

to a PV system Photovoltaic modules consist of a large number of solar cells and use light energy from the Sun to generate electricity through the photovoltaic effect. Most modules use wafer-based crystalline silicon cells or thin-film cells. The structural (load carrying) member of a module can be either the top layer or the back layer. Cells must be protected from mechanical damage and moisture. The cells and modules are usually connected electrically in series, one to another to increase the desired voltage output, and then in parallel to increase current output to create the solar panel. Most panels are rigid, but semi-flexible ones based on thin-film cells are also available. The power (in watts) of the solar panel is the voltage (in volts) multiplied by the current (in amperes), and depends both on the amount of light and on the electrical load connected to the panel. The manufacturing specifications on solar panels are obtained under standard conditions, which are usually not the true operating conditions the solar panels are exposed to on the installation site. A PV junction box is attached to the back of the solar panel and functions as its output interface. External connections for most photovoltaic modules use MC4 connectors to facilitate easy weatherproof connections to the rest of the system. A USB power interface can also be used. Solar panels also use metal frames consisting of racking components, brackets, reflector shapes, and troughs to better support the panel structure. Cell connection techniques Solar cells need to be connected together by electrodes to form a module, with front electrodes blocking the solar cell front optical surface area slightly. To improve solar cell efficiency manufacturers maximize frontal surface area available for sunlight and improve sunlight absorption using chronologically adopted, varying rear electrode solar cell connection techniques: • Aluminum back surface field (Al-BSF), a vintage technology, uses full aluminum rear contact face • Passivated emitter rear contact (PERC) uses a reduced aluminum rear contact face and adds a polymer film where aluminum was removed to capture light • Interdigitated back contact (IBC) places contacts fully on the back allowing full frontal light exposure to capture even more light • Extended back contact (XBC) uses a combination of the above technologies Tandem solar cells use one of the above connection techniques and a combination of cell chemistries to form a solar cell. Arrays of solar panels A single solar panel can produce only a limited amount of power; most installations contain multiple panels adding their voltages or currents. A photovoltaic system typically includes an array of photovoltaic modules, an inverter, a battery pack for energy storage, a charge controller, interconnection wiring, circuit breakers, fuses, disconnect switches, voltage meters, and optionally a solar tracking mechanism. Equipment is carefully selected to optimize energy output and storage, reduce power transmission losses, and many times convert from direct current to alternating current. Smart solar panels Smart solar panels have power electronics embedded in the panel and are different from traditional solar panels with power electronics attached to the frame or connected to the photovoltaic circuit through a connector. Solar power electronics can be used for: • Maximum power point tracking power optimizers, a technology developed to maximize the power harvest from solar photovoltaic systems by compensating for shading effects, wherein a shadow falling on a section of a module causes the electrical output of one or more strings of cells in the module to fall to near zero, but not having the output of the entire module fall to zero. • Solar performance monitors for data collection • Fault detection for enhanced safety Technology Most solar modules are currently produced from crystalline silicon (c-Si) solar cells made of polycrystalline or monocrystalline silicon. In 2021, crystalline silicon accounted for 95% of worldwide PV production, while the rest of the overall market is made up of thin-film technologies using cadmium telluride (CdTe), copper indium gallium selenide and amorphous silicon . Bifacial cells produce energy on both sides which increases the total output of the module, this boost depends on the reflectivity of the surroundings and benefits from raised constructions since more light can reach the rear side. The gain is situational, the rear side benefits more from high-albedo surroundings such as snow, raised constructions and overcast weather but the gains might be minimal when the panels are installed directly on a surface with little clearance making it not cost-effective in those cases. The price of bifacial cells has dropped enough to be close to monofacial technologies, because of this as of 2024, bifacial panels are the leading choice for utility-scale PV installations. Emerging, third-generation solar technologies use advanced thin-film cells. They produce a relatively high-efficiency conversion for a lower cost compared with other solar technologies. Also, high-cost, high-efficiency, and close-packed rectangular multi-junction solar cells are usually used in solar panels on spacecraft, as they offer the highest ratio of generated power per kilogram lifted into space. Multi-junction cells are compound semiconductors and made of gallium arsenide and other semiconductor materials. Another emerging PV technology using multi-junction cells is concentrator photovoltaics. Thin film Concentrator Some special solar PV modules include concentrators in which light is focused by lenses or mirrors onto smaller cells. This enables the cost-effective use of highly efficient, but expensive cells (such as gallium arsenide) with the trade-off of using a higher solar exposure area. Concentrating the sunlight can also raise the efficiency to around 45%. Light capture The amount of light absorbed by a solar cell depends on the sunlight angle of incidence and intensity. Light absorption varies because the amount falling on the panel is proportional to the cosine of the angle of incidence, and partly because at high angle of incidence more light is reflected. Modules usually are faced south (in the Northern Hemisphere) or north (in the Southern Hemisphere) with a particular tilt calculated according to the latitude, to maximize total energy output over a day. Solar tracking can be used to adjust the tilt angle from dawn to dusk, to keep the angle of incidence small. Vertical orientation of bi-facial panels are oriented north south and capture the most light from the east in the morning and west in the afternoon. Photovoltaic manufacturers have been working to decrease reflectance with improved anti-reflective coatings or with textures. Anti-reflective coatings use one or more thin layers of substances with refractive indices intermediate between that of silicon and that of air, causing destructive interference of the reflected light. Power curve In individual solar panels, if not enough current is taken, then power isn't maximised. If too much current is taken then the voltage collapses. The optimum current draw is roughly proportional to the amount of sunlight striking the panel. Solar panel capacity is specified by the MPP (maximum power point) value of solar panels in full sunlight. Inverters Solar inverters convert the direct current power provided by panels to alternating current power. MPP (Maximum power point) of the solar panel consists of MPP voltage (V) and MPP current (I). Performing maximum power point tracking, a solar inverter samples the output (I-V curve) from the solar cell and applies the proper electrical load to obtain maximum power. An alternating current solar panel has a small direct current to alternating current microinverter on the back and produces alternating current power with no external direct current connector. Alternating current modules are defined by Underwriters Laboratories as the smallest and most complete system for harvesting solar energy. Micro-inverters work independently to enable each panel to contribute its maximum possible output for a given amount of sunlight, but can be more expensive. Solar panel interconnection Solar panel electrical interconnections are made of conductors that carry current and are sized according to the current rating and fault conditions; sometimes including in-line fuses. Panels are typically connected in series of one or more panels to form strings to achieve a desired output voltage, and strings can be connected in parallel to provide the desired current (ampere) capability of the PV system. In string connections the voltages of the modules add, but the current is determined by the lowest performing panel. This is known as the "Christmas light effect". In parallel connections the voltages will be the same, but the currents add. Arrays are connected up to meet the voltage requirements of the inverters and to not greatly exceed the current limits. Blocking and bypass diodes may be incorporated within the module or used externally to deal with partial array shading, in order to maximize output. For series connections, bypass diodes are placed in parallel with modules to allow current to bypass shaded modules with a lower output voltage which would severely limit the current. For paralleled connections, a blocking diode may be placed in series with each module's string to prevent current flowing backwards through shaded strings thus short-circuiting other strings. If three or more strings are connected in parallel, fuses are generally included on each string to eliminate the possibility of diode failures overloading the panels and wiring and causing fires. Connectors Outdoor solar panels usually include MC4 connectors, automotive solar panels may include an auxiliary power outlet and/or USB adapter and indoor panels may have a microinverter. == Efficiency ==

) Each module is rated by its DC output power under standard test conditions and hence the on field output power might vary. Power typically ranges from 100 to 365 Watts (W). The efficiency of a module determines the area of a module given the same rated output an 8% efficient 230 W module will have twice the area of a 16% efficient 230 W module. Some commercially available solar modules exceed 24% efficiency. As of 2025, the best achieved sunlight conversion rate (solar module efficiency) is around 24.5% in new commercial products typically lower than the efficiencies of their cells in isolation. The most efficient mass-produced solar modules have power density values of up to 175 W/m2 (16.22 W/ft2). The current versus voltage curve of a module provides useful information about its electrical performance. Globally, capacity factor for utility-scale PV farms was 16.1% in 2019. Overheating is the most important factor for the efficiency of the solar panel. Radiation-dependent efficiency Depending on construction, photovoltaic modules can produce electricity from a range of frequencies of light, but usually cannot cover the entire solar radiation range (specifically, ultraviolet, infrared and low or diffused light). Hence, much of the incident sunlight energy is wasted by solar modules, and they can give far higher efficiencies if illuminated with monochromatic light. Therefore, another design concept is to split the light into six to eight different wavelength ranges that will produce a different color of light, and direct the beams onto different cells tuned to those ranges. == Performance and degradation ==

Module performance is generally rated under standard test conditions: irradiance of 1,000 W/m2, solar spectrum of AM 1.5 and module temperature at 25 °C. The actual voltage and current output of the module changes as lighting, temperature and load conditions change, so there is never one specific voltage at which the module operates. Performance varies depending on geographic location, time of day, the day of the year, amount of solar irradiance, direction and tilt of modules, cloud cover, shading, soiling, state of charge, and temperature. Performance of a module or panel can be measured at different time intervals with a direct current clamp meter or shunt and logged, graphed, or charted with a chart recorder or data logger. For optimum performance, a solar panel string needs to be made of similar electrical voltage solar panels oriented in the same direction perpendicular to direct sunlight. Bypass diodes are used to optimize output by allowing continuous current flow by circumventing broken or shaded panels. Electrical characteristics include nominal power (PMAX, measured in W), open-circuit voltage (VOC), short-circuit current (ISC, measured in amperes), maximum power voltage (VMPP), maximum power current (IMPP), peak power, (watt-peak, Wp), and module efficiency (%). Open-circuit voltage or VOC is the maximum voltage the module can produce when not connected to an electrical circuit or system. VOC can be measured with a voltmeter directly on an illuminated module's terminals or on its disconnected cable. The peak power rating, Wp, is the maximum output under standard test conditions (not the maximum possible output). Typical modules, which could measure approximately , will be rated from as low as 75 W to as high as 600 W, depending on their efficiency. At the time of testing, the test modules are binned according to their test results, and a typical manufacturer might rate their modules in 5 W increments, and either rate them at +/- 3%, +/-5%, +3/-0% or +5/-0%. Influence of temperature The performance of a photovoltaic (PV) module depends on the environmental conditions, mainly on the global incident irradiance G in the plane of the module. However, the temperature T of the p–n junction also influences the main electrical parameters: the short circuit current ISC, the open circuit voltage VOC and the maximum power Pmax. In general, it is known that VOC shows a significant inverse correlation with T, while for ISC this correlation is direct, but weaker, so that this increase does not compensate for the decrease in VOC. As a consequence, Pmax decreases when T increases. This correlation between the power output of a solar cell and the working temperature of its junction depends on the semiconductor material, and is due to the influence of T on the concentration, lifetime, and mobility of the intrinsic carriers, i.e., electrons and gaps. inside the photovoltaic cell. Temperature sensitivity is usually described by temperature coefficients, each of which expresses the derivative of the parameter to which it refers with respect to the junction temperature. The values of these parameters can be found in any data sheet of the photovoltaic module; are the following: - β: VOC variation coefficient with respect to T, given by ∂VOC/∂T. - α: Coefficient of variation of ISC with respect to T, given by ∂ISC/∂T. - δ: Coefficient of variation of Pmax with respect to T, given by ∂Pmax/∂T. Techniques for estimating these coefficients from experimental data can be found in the literature Studies have shown that while high temperatures negatively impact efficiency, colder temperatures can improve solar panel performance due to reduced electrical resistance within the cells. However, winter conditions introduce additional challenges such as snow accumulation and reduced daylight hours, which can offset the efficiency benefits of lower temperatures. Solar panels are still capable of generating power in winter, but overall output may be lower due to limited sunlight exposure and potential obstructions. Degradation The ability of solar modules to withstand damage by rain, hail, heavy snow load, and cycles of heat and cold varies by manufacturer, although most solar panels on the U.S. market are UL listed, meaning they have gone through testing to withstand hail. Potential-induced degradation (also called PID) is a potential-induced performance degradation in crystalline photovoltaic modules, caused by so-called stray currents. This effect may cause power loss of up to 30%. The power output of a photovoltaic (PV) device decreases over time due to exposure to solar radiation as well as other external conditions. The degradation index, defined as the annual percentage of output power loss, is a key factor in determining the long-term production of a photovoltaic plant. To estimate this degradation, the percentage of decrease associated with each of the electrical parameters is calculated. Individual degradation of a solar panel can negatively influence the performance of a complete string. Furthermore, not all solar panels in the same installation decrease their performance at exactly the same rate. There are several studies dealing with the power degradation analysis of solar panels based on different photovoltaic technologies available in the literature. According to a recent study, the degradation of crystalline silicon solar panels is linear, between 0.8% and 1.0% per year. On the other hand, if we analyze the performance of thin-film photovoltaic modules, an initial period of strong degradation is observed (which can last several months and even up to 2 years), followed by a later stage in which the degradation stabilizes, being then comparable to that of crystalline silicon. Strong seasonal variations are also observed in such thin-film technologies because the influence of the solar spectrum is much greater. Solar panels of amorphous silicon, micromorphic silicon or cadmium telluride, can have annual degradation rates for the first years of between 3% and 4%. Copper indium gallium selenide solar panels show lower degradation rates than crystalline silicon, even in early years. == Mounting and tracking ==

s Ground Large utility-scale solar power plants frequently use ground-mounted photovoltaic systems. Their solar modules are held in place by racks or frames that are attached to ground-based mounting supports. Ground based mounting supports include: • Pole mounts, which are driven directly into the ground or embedded in concrete. • Foundation mounts, such as concrete slabs or poured footings • Ballasted footing mounts, such as concrete or steel bases that use weight to secure the solar module system in position and do not require ground penetration. This type of mounting system is well suited for sites where excavation is not possible such as capped landfills and simplifies decommissioning or relocation of solar module systems. Vertical bifacial solar array Vertical bifacial solar panels are oriented towards east and west rather than south, this allows them to utilize the sun's irradiance more efficiently in the morning and evening. In most cases this results in a slightly lower total output, but matches energy demand better than a south facing installation and helps reduce the duck curve problem. Applications include agrivoltaics, solar fencing, highway and railroad noise dampeners and barricades. Vertical bifacial solar panels are well suited for high-latitude locations, such as the Nordics, due to the low average solar altitude angle. File:Agrivoltaic installation Foulum.jpg|Agrivoltaic vertical bifacial solar panels File:Vertical Bifacial vs South facing solar array.webp|Vertical Bifacial vs south facing solar array power output Roof Roof-mounted solar power systems consist of solar modules held in place by racks or frames attached to roof-based mounting supports. Roof-based mounting supports include: • Rail mounts, which are attached directly to the roof structure and may use additional rails for attaching the module racking or frames. • Ballasted footing mounts, such as concrete or steel bases that use weight to secure the panel system in position and do not require through penetration. This mounting method allows for decommissioning or relocation of solar panel systems with no adverse effect on the roof structure. • All wiring connecting adjacent solar modules to the energy harvesting equipment must be installed according to local electrical codes and should be run in a conduit appropriate for the climate conditions Solar canopy parking lot in New Haven at Hotel Marcel. There are EV level 2 chargers underneath the canopy and a 12-stall Tesla Supercharger behind. Solar canopies are solar arrays which are installed on top of a traditional canopy. These canopies could be a parking lot canopy, carport, gazebo, Pergola, or patio cover. There are many benefits, which include maximizing the space available in urban areas while also providing shade for cars. The energy produced can be used to create electric vehicle (EV) charging stations. Portable Portable solar panels can ensure electric current, enough to charge devices (mobile, radio, ...) via USB-port or to charge a powerbank. Special features of portable solar panels include high flexibility, high durability & waterproof characteristics good for travel and camping. Tracking Solar trackers increase the energy produced per module at the cost of mechanical complexity and increased need for maintenance. They sense the direction of the Sun and tilt or rotate the modules as needed for maximum exposure to the light. Alternatively, fixed racks can hold modules stationary throughout the day at a given tilt (zenith angle) and facing a given direction (azimuth angle). Tilt angles equivalent to an installation's latitude are common. Some systems may also adjust the tilt angle based on the time of year. On the other hand, east- and west-facing arrays (covering an east–west facing roof, for example) are commonly deployed. Even though such installations will not produce the maximum possible average power from the individual solar panels, the cost of the panels is now usually cheaper than the tracking mechanism and they can provide more economically valuable power during morning and evening peak demands than north or south facing systems. == Maintenance ==

Solar panel conversion efficiency, typically in the 20% range, is reduced by the accumulation of dust, grime, pollen, and other particulates on the solar panels, collectively referred to as soiling. "A dirty solar panel can reduce its power capabilities by up to 30% in high dust/pollen or desert areas", says Seamus Curran, associate professor of physics at the University of Houston and director of the Institute for NanoEnergy, which specializes in the design, engineering, and assembly of nanostructures. The average soiling loss in the world in 2018 is estimated to be at least 3% – 4%. Paying to have solar panels cleaned is a good investment in many regions, as of 2019. There are also occupational hazards with solar panel installation and maintenance. A 2015–2018 study in the UK investigated 80 PV-related incidents of fire, with over 20 "serious fires" directly caused by PV installation, including 37 domestic buildings and 6 solar farms. In of the incidents a root cause was not established and in a majority of others was caused by poor installation, faulty product or design issues. The most frequent single element causing fires was the direct current isolators. A 2021 study by kWh Analytics found that, at a system level, the median annual degradation of PV installations was 1.09% for residential and 0.8% for non-residential. This was significantly more than the common industry assumption of 0.5% per year, which was taken from an estimate of panel-level degradation. A 2021 module reliability study found an increasing trend in solar module failure rates with 30% of manufacturers experiencing safety failures related to junction boxes (growth from 20%) and 26% bill-of-materials failures (growth from 20%). Cleaning Cleaning methods for solar panels can be divided into 5 groups: manual tools, mechanized tools (such as tractor mounted brushes), installed hydraulic systems (such as sprinklers), installed robotic systems, and deployable robots. Manual cleaning tools are by far the most prevalent method of cleaning, most likely because of the low purchase cost. However, in a Saudi Arabian study done in 2014, it was found that "installed robotic systems, mechanized systems, and installed hydraulic systems are likely the three most promising technologies for use in cleaning solar panels". Novel self-cleaning mechanisms for solar panels are being developed. For instance, in 2019 via wet-chemically etched nanowires and a hydrophobic coating on the surface water droplets could remove 98% of dust particles, which may be especially relevant for applications in the desert. In March 2022, MIT researchers announced the development of a waterless cleaning system for solar panels and mirrors to address the issue of dust accumulation, which can reduce solar output by up to 30 percent in one month. This system utilizes electrostatic repulsion to detach dust particles from the panel's surface, eliminating the need for water or brushes. An electrical charge imparted to the dust particles by passing a simple electrode over the panel causes them to be repelled by a charge applied to the panel itself. The system can be automated using a basic electric motor and guide rails. == Waste and recycling ==

There were 30 thousand tonnes of PV waste in 2021, and the annual amount was estimated by Bloomberg NEF to rise to more than 1 million tons by 2035 and more than 10 million by 2050. For comparison, 750 million tons of fly ash waste was produced by coal power in 2022. In the United States, around 90% of decommissioned solar panels end up in landfills as of 2023. Most parts of a solar module can be recycled including up to 95% of certain semiconductor materials or the glass as well as large amounts of ferrous and non-ferrous metals. Some private companies and non-profit organizations take-back and recycle end-of-life modules. EU law requires manufacturers to ensure their solar panels are recycled properly. Similar legislation is underway in Japan, India, and Australia. A 2023 Australian report said that there is a market for quality used panels and made recommendations for increasing reuse, but rules have not been implemented. Recycling possibilities depend on the kind of technology used in the modules: • Silicon based modules: aluminum frames and junction boxes are dismantled manually at the beginning of the process. The module is then crushed in a mill and the different fractions are separated – glass, plastics and metals. It is possible to recover more than 80% of the incoming weight. This process can be performed by flat glass recyclers, since the shape and composition of a PV module is similar to flat glass used in the building and automotive industry. The recovered glass, for example, is readily accepted by the glass foam and glass insulation industry. • Non-silicon based modules: they require specific recycling technologies such as the use of chemical baths in order to separate the different semiconductor materials. For cadmium telluride modules, the recycling process begins by crushing the module and subsequently separating the different fractions. This recycling process is designed to recover up to 90% of the glass and 95% of the semiconductor materials contained. Some commercial-scale recycling facilities have been created in recent years by private companies. Since 2010, there is an annual European conference bringing together manufacturers, recyclers and researchers to look at the future of PV module recycling. == Production ==

The production of PV systems has followed a classic learning curve effect, with significant cost reduction occurring alongside large rises in efficiency and production output. With over 100% year-on-year growth in PV system installation, PV module makers dramatically increased their shipments of solar modules in 2019. They actively expanded their capacity and turned themselves into gigawatt GW players. According to Pulse Solar, five of the top ten PV module companies in 2019 have experienced a rise in solar panel production by at least 25% compared to 2019. The basis of producing most solar panels is mostly on the use of silicon cells. These silicon cells are typically 10–20% efficient at converting sunlight into electricity, with newer production models exceeding 22%. In 2018, the world's top five solar module producers in terms of shipped capacity during the calendar year of 2018 were Jinko Solar, JA Solar, Trina Solar, Longi solar, and Canadian Solar. Environmental impact The manufacture of PV panels depends on the use of toxic and reactive chemicals. These include cadmium telluride, copper indium selenide, cadmium gallium (di)selenide, copper indium gallium (di)selenide, hexafluoroethane, lead, and polyvinyl fluoride. Byproducts include silicon tetrachloride. Silicon dust ("kerf") is produced when the silicon wafers are sawn. == Price ==

–stating that solar module prices have dropped about 20% for each doubling of installed capacity—defines the "learning rate" of solar photovoltaics. The price of solar electrical power has continued to fall so that in many countries it has become cheaper than fossil fuel electricity from the electricity grid since 2012, a phenomenon known as grid parity. The price of a solar array only continues to fall. Average pricing information divides in three pricing categories: those buying small quantities (modules of all sizes in the kilowatt range annually), mid-range buyers (typically up to 10 MWp annually), and large quantity buyers (self-explanatory—and with access to the lowest prices). Over the long term there is clearly a systematic reduction in the price of cells and modules. For example, in 2012 it was estimated that the quantity cost per watt was about US$0.60, which was 250 times lower than the cost in 1970 of US$150. A 2015 study shows price/kWh dropping by 10% per year since 1980, and predicts that solar could contribute 20% of total electricity consumption by 2030, whereas the International Energy Agency predicts 16% by 2050. Real-world energy production costs depend a great deal on local weather conditions. In a cloudy country such as the United Kingdom, the cost per produced kWh is higher than in sunnier countries like Spain. File:Energy pricing longterm.png|thumb|upright=1.25|Long term normalized cost comparisons demonstrating value of various electric generation technologies == Standards ==

Standards generally used in photovoltaic modules: • IEC 61215 (crystalline silicon performance), 61646 (thin film performance) and 61730 (all modules, safety), 61853 (Photovoltaic module performance testing & energy rating) • ISO 9488 Solar energy—Vocabulary. • UL 1703 from Underwriters Laboratories • UL 1741 from Underwriters Laboratories • UL 2703 from Underwriters Laboratories • CE mark • Electrical Safety Tester (EST) Series (EST-460, EST-22V, EST-22H, EST-110). == Applications ==

There are many practical applications for the use of solar panels or photovoltaics. It can first be used in agriculture as a power source for irrigation. In health care solar panels can be used to refrigerate medical supplies. It can also be used for infrastructure. PV modules are used in photovoltaic systems and include a large variety of electric devices. == Limitations ==

Impact on electricity network With the increasing levels of rooftop photovoltaic systems, the energy flow becomes 2-way. When there is more local generation than consumption, electricity is exported to the grid. However, an electricity network traditionally is not designed to deal with the 2- way energy transfer. Therefore, some technical issues may occur. For example, in Queensland Australia, more than 30% of households used rooftop PV by the end of 2017. The duck curve appeared often for a lot of communities from 2015 onwards. An over-voltage issue may result as the electricity flows from PV households back to the network. There are solutions to manage the over voltage issue, such as regulating PV inverter power factor, new voltage and energy control equipment at the electricity distributor level, re-conducting the electricity wires, demand side management, etc. There are often limitations and costs related to these solutions. For rooftop solar to be able to provide enough backup power during a power cut a battery is often also required. == Quality assurance ==

Solar module quality assurance involves testing and evaluating solar cells and Solar Panels to ensure the quality requirements of them are met. Solar modules (or panels) are expected to have a long service life between 20 and 40 years. They should continually and reliably convey and deliver the power anticipated. Solar modules can be tested through a combination of physical tests, laboratory studies, and numerical analyses. Furthermore, solar modules need to be assessed throughout the different stages of their life cycle. Various companies such as Southern Research Energy & Environment, SGS Consumer Testing Services, TÜV Rheinland, Sinovoltaics, Clean Energy Associates (CEA), CSA Solar International and Enertis provide services in solar module quality assurance."The implementation of consistent traceable and stable manufacturing processes becomes mandatory to safeguard and ensure the quality of the PV Modules" Certification is carried out according to standards ANSI/UL1703, IEC 17025, IEC 61215, IEC 61701, and IEC 61730-1/-2 == See also ==