Transform fault

Transform boundaries are also known as conservative plate boundaries because they involve no addition or loss of lithosphere at the Earth's surface. == Background ==

Geophysicist and geologist John Tuzo Wilson recognized that the offsets of oceanic ridges by faults do not follow the classical pattern of an offset fence or geological marker in Reid's rebound theory of faulting, from which the sense of slip is derived. The new class of faults, called transform faults, produce slip in the opposite direction from what one would surmise from the standard interpretation of an offset geological feature. Slip along transform faults does not increase the distance between the ridges it separates; the distance remains constant in earthquakes because the ridges are spreading centers. This hypothesis was confirmed in a study of the fault plane solutions that showed the slip on transform faults points in the opposite direction than classical interpretation would suggest. ==Difference between transform and transcurrent faults==

Transform faults are closely related to transcurrent faults and are commonly confused. Both types of fault are strike-slip or side-to-side in movement; nevertheless, transform faults always end at a junction with another plate boundary, while transcurrent faults may die out without a junction with another fault. Finally, transform faults form a tectonic plate boundary, while transcurrent faults do not. ==Mechanics==

Faults in general are focused areas of deformation or strain, which are the response of built-up stresses in the form of compression, tension, or shear stress in rock at the surface or deep in the Earth's subsurface. Transform faults specifically accommodate lateral strain by transferring displacement between mid-ocean ridges or subduction zones. They also act as the plane of weakness, which may result in splitting in rift zones. ==Transform faults and divergent boundaries==

Transform faults are commonly found linking segments of divergent boundaries (mid-oceanic ridges or spreading centres). These mid-oceanic ridges are where new seafloor is constantly created through the upwelling of new basaltic magma. With new seafloor being pushed and pulled out, the older seafloor slowly slides away from the mid-oceanic ridges toward the continents. Although separated only by tens of kilometers, this separation between segments of the ridges causes portions of the seafloor to push past each other in opposing directions. This lateral movement of seafloors past each other is where transform faults are currently active. Transform faults move differently from a strike-slip fault at the mid-oceanic ridge. Instead of the ridges moving away from each other, as they do in other strike-slip faults, transform-fault ridges remain in the same, fixed locations, and the new ocean seafloor created at the ridges is pushed away from the ridge. Evidence of this motion can be found in paleomagnetic striping on the seafloor. A paper written by geophysicist Taras Gerya theorizes that the creation of the transform faults between the ridges of the mid-oceanic ridge is attributed to rotated and stretched sections of the mid-oceanic ridge. This occurs over a long period of time with the spreading center or ridge slowly deforming from a straight line to a curved line. Finally, fracturing along these planes forms transform faults. As this takes place, the fault changes from a normal fault with extensional stress to a strike-slip fault with lateral stress. In the study done by Bonatti and Crane, peridotite and gabbro rocks were discovered in the edges of the transform ridges. These rocks are created deep inside the Earth's mantle and then rapidly exhumed to the surface. This evidence helps to prove that new seafloor is being created at the mid-oceanic ridges and further supports the theory of plate tectonics. Active transform faults are between two tectonic structures or faults. Fracture zones represent the previously active transform-fault lines, which have since passed the active transform zone and are being pushed toward the continents. These elevated ridges on the ocean floor can be traced for hundreds of miles and in some cases even from one continent across an ocean to the other continent. ==Types==

In his work on transform-fault systems, geologist Tuzo Wilson said that transform faults must be connected to other faults or tectonic-plate boundaries on both ends; because of that requirement, transform faults can grow in length, keep a constant length, or decrease in length. == Examples ==

The most prominent examples of the mid-oceanic ridge transform zones are in the Atlantic Ocean between South America and Africa. Known as the St. Paul, Romanche, Chain, and Ascension fracture zones, these areas have deep, easily identifiable transform faults and ridges. Other locations include: the East Pacific Ridge located in the South Eastern Pacific Ocean, which meets up with San Andreas Fault to the North. Transform faults are not limited to oceanic crust and spreading centers; many of them are on continental margins. The best example is the San Andreas Fault on the Pacific coast of the United States. The San Andreas Fault links the East Pacific Rise off the West coast of Mexico (Gulf of California) to the Mendocino triple junction (Part of the Juan de Fuca plate) off the coast of the Northwestern United States, making it a ridge-to-transform-style fault. During this period, the Farallon plate, followed by the Pacific plate, collided into the North American plate. Other examples include: • Middle East's Dead Sea Transform Fault • Pakistan's Chaman Fault • Turkey's North Anatolian Fault • North America's Queen Charlotte Fault • Myanmar's Sagaing Fault == See also ==