Analog computer

Precursors This is a list of examples of early computation devices considered precursors of the modern computers. Some of them may even have been dubbed 'computers' by the press, though they may fail to fit modern definitions. , dating from between 200 BC and 80 BC, was an early analog computer. The Antikythera mechanism, a type of device used to determine the positions of heavenly bodies known as an orrery, was described as an early mechanical analog computer by British physicist, information scientist, and historian of science Derek J. de Solla Price. It was discovered in 1901, in the Antikythera wreck off the Greek island of Antikythera, between Kythera and Crete, and has been dated to , during the Hellenistic period. Devices of a level of complexity comparable to that of the Antikythera mechanism would not reappear until a thousand years later. Many mechanical aids to calculation and measurement were constructed for astronomical and navigation use. The planisphere was first described by Ptolemy in the 2nd century AD. The astrolabe was invented in the Hellenistic world in either the 1st or 2nd centuries BC and is often attributed to Hipparchus. A combination of the planisphere and dioptra, the astrolabe was effectively an analog computer capable of working out several different kinds of problems in spherical astronomy. The sector, a calculating instrument used for solving problems in proportion, trigonometry, multiplication and division, and for various functions, such as squares and cube roots, was developed in the late 16th century and found application in gunnery, surveying and navigation. The planimeter was a manual instrument to calculate the area of a closed figure by tracing over it with a mechanical linkage. . The sliding central slip is set to 1.3, the cursor to 2.0 and points to the multiplied result of 2.6 when reading scales C and D. The slide rule was invented around 1620–1630, shortly after the publication of the concept of the logarithm. It is a hand-operated analog computer for doing multiplication and division. As slide rule development progressed, added scales provided reciprocals, squares and square roots, cubes and cube roots, as well as transcendental functions such as logarithms and exponentials, circular and hyperbolic trigonometry and other functions. Slide rules have been largely rendered obsolete by electronic calculators, though purpose-built variants persist in some niches, notably the E6-B flight computer for pilot training. In 1831–1835, mathematician and engineer Giovanni Plana devised a perpetual-calendar machine, which, through a system of pulleys and cylinders, could predict the perpetual calendar for every year from AD 0 (that is, 1 BC) to AD 4000, keeping track of leap years and varying day length. The tide-predicting machine invented by Sir William Thomson in 1872 was of great utility to navigation in shallow waters. It used a system of pulleys and wires to automatically calculate predicted tide levels for a set period at a particular location. The differential analyser, a mechanical analog computer designed to solve differential equations by integration, used wheel-and-disc mechanisms to perform the integration. In 1876 James Thomson had already discussed the possible construction of such calculators, but he had been stymied by the limited output torque of the ball-and-disk integrators. Several systems followed, notably those of Spanish engineer Leonardo Torres Quevedo, who built various analog machines for solving real and complex roots of polynomials; and Michelson and Stratton, whose Harmonic Analyser performed Fourier analysis, but using an array of 80 springs rather than Kelvin integrators. This work led to the mathematical understanding of the Gibbs phenomenon of overshoot in Fourier representation near discontinuities. In a differential analyzer, the output of one integrator drove the input of the next integrator, or a graphing output. The torque amplifier was the advance that allowed these machines to work. Starting in the 1920s, Vannevar Bush and others developed mechanical differential analyzers. Modern era The Dumaresq was a mechanical calculating device invented around 1902 by Lieutenant John Dumaresq of the Royal Navy. It was an analog computer that related vital variables of the fire control problem to the movement of one's own ship and that of a target ship. It was often used with other devices, such as a Vickers range clock to generate range and deflection data so the gun sights of the ship could be continuously set. A number of versions of the Dumaresq were produced of increasing complexity as development proceeded. By 1912, Arthur Pollen had developed an electrically driven mechanical analog computer for fire-control systems, based on the differential analyser. It was used by the Imperial Russian Navy in World War I. Starting in 1929, AC network analyzers were constructed to solve calculation problems related to electrical power systems that were too large to solve with numerical methods at the time. These were essentially scale models of the electrical properties of the full-size system. Since network analyzers could handle problems too large for analytic methods or hand computation, they were also used to solve problems in nuclear physics and in the design of structures. More than 50 large network analyzers were built by the end of the 1950s. World War II era gun directors, gun data computers, and bomb sights used mechanical analog computers. In 1942 Helmut Hölzer built a fully electronic analog computer at Peenemünde Army Research Center as an embedded control system (mixing device) to calculate V-2 rocket trajectories from the accelerations and orientations (measured by gyroscopes) and to stabilize and guide the missile. Mechanical analog computers were very important in gun fire control in World War II, the Korean War and well past the Vietnam War; they were made in significant numbers. In the period 1930–1945 in the Netherlands, Johan van Veen developed an analogue computer to calculate and predict tidal currents when the geometry of the channels are changed. Around 1950, this idea was developed into the Deltar, a hydraulic analogy computer supporting the closure of estuaries in the southwest of the Netherlands (the Delta Works). The FERMIAC was an analog computer invented by physicist Enrico Fermi in 1947 to aid in his studies of neutron transport. Project Cyclone was an analog computer developed by Reeves in 1950 for the analysis and design of dynamic systems. Project Typhoon was an analog computer developed by RCA in 1952. It consisted of over 4,000 electron tubes and used 100 dials and 6,000 plug-in connectors to program. The MONIAC Computer was a hydraulic analogy of a national economy first unveiled in 1949. Computer Engineering Associates was spun out of Caltech in 1950 to provide commercial services using the "Direct Analogy Electric Analog Computer" ("the largest and most impressive general-purpose analyzer facility for the solution of field problems") developed there by Gilbert D. McCann, Charles H. Wilts, and Bart Locanthi. Educational analog computers illustrated the principles of analog calculation. The Heathkit EC-1, a $199 educational analog computer, was made by the Heath Company, US . It was programmed using patch cords that connected nine operational amplifiers and other components. General Electric also marketed an "educational" analog computer kit of a simple design in the early 1960s consisting of two transistor tone generators and three potentiometers wired such that the frequency of the oscillator was nulled when the potentiometer dials were positioned by hand to satisfy an equation. The relative resistance of the potentiometer was then equivalent to the formula of the equation being solved. Multiplication or division could be performed, depending on which dials were inputs and which was the output. Accuracy and resolution was limited and a simple slide rule was more accurate. However, the unit did demonstrate the basic principle. Analog computer designs were published in electronics magazines. One example is the PEAC (Practical Electronics analogue computer), published in Practical Electronics in the January 1968 edition. Another more modern hybrid computer design was published in Everyday Practical Electronics in 2002. An example described in the EPE hybrid computer was the flight of a VTOL aircraft such as the Harrier jump jet. The altitude and speed of the aircraft were calculated by the analog part of the computer and sent to a PC via a digital microprocessor and displayed on the PC screen. In industrial process control, analog loop controllers were used to automatically regulate temperature, flow, pressure, or other process conditions. The technology of these controllers ranged from purely mechanical integrators, through vacuum-tube and solid-state devices, to emulation of analog controllers by microprocessors. ==Electronic analog computers==

(1959) of a Claas tractor (1986) The similarity between linear mechanical components, such as springs and dashpots (viscous-fluid dampers), and electrical components, such as capacitors, inductors, and resistors is striking in terms of mathematics. They can be modeled using equations of the same form. However, the difference between these systems is what makes analog computing useful. Complex systems often are not amenable to pen-and-paper analysis, and require some form of testing or simulation. Complex mechanical systems, such as suspensions for racing cars, are expensive to fabricate and hard to modify. And taking precise mechanical measurements during high-speed tests adds further difficulty. By contrast, it is very inexpensive to build an electrical equivalent of a complex mechanical system, to simulate its behavior. Engineers arrange a few operational amplifiers (op amps) and some passive linear components to form a circuit that follows the same equations as the mechanical system being simulated. All measurements can be taken directly with an oscilloscope. In the circuit, the (simulated) stiffness of the spring, for instance, can be changed by adjusting the parameters of an integrator. The electrical system is an analogy to the physical system, hence the name, but it is much less expensive than a mechanical prototype, much easier to modify, and generally safer. The electronic circuit can also be made to run faster or slower than the physical system being simulated. Experienced users of electronic analog computers said that they offered a comparatively intimate control and understanding of the problem, relative to digital simulations. (SEA) Electronic analog computers are especially well-suited to representing situations described by differential equations. Historically, they were often used when a system of differential equations proved very difficult to solve by traditional means. As a simple example, the dynamics of a spring-mass system can be described by the equation m \ddot y + d \dot y +cy = mg, with y as the vertical position of a mass m, d the damping coefficient, c the spring constant and g the gravity of Earth. For analog computing, the equation is programmed as \ddot y = - \tfrac{d}{m} \dot y - \tfrac{c}{m} y - g. The equivalent analog circuit consists of two integrators for the state variables -\dot y (speed) and y (position), one inverter, and three potentiometers. Electronic analog computers have drawbacks: the value of the circuit's supply voltage limits the range over which the variables may vary (since the value of a variable is represented by a voltage on a particular wire). Therefore, each problem must be scaled so its parameters and dimensions can be represented using voltages that the circuit can supply —e.g., the expected magnitudes of the velocity and the position of a spring pendulum. Improperly scaled variables can have their values "clamped" by the limits of the supply voltage. Or if scaled too small, they can suffer from higher noise levels. Either problem can cause the circuit to produce an incorrect simulation of the physical system. (Modern digital simulations are much more robust to widely varying values of their variables, but are still not entirely immune to these concerns: floating-point digital calculations support a huge dynamic range, but can suffer from imprecision if tiny differences of huge values lead to numerical instability.) The precision of the analog computer readout was limited chiefly by the precision of the readout equipment used, generally three or four significant figures. (Modern digital simulations are much better in this area. Digital arbitrary-precision arithmetic can provide any desired degree of precision.) However, in most cases the precision of an analog computer is absolutely sufficient given the uncertainty of the model characteristics and its technical parameters. Many small computers dedicated to specific computations are still part of industrial regulation equipment, but from the 1950s to the 1970s, general-purpose analog computers were the only systems fast enough for real time simulation of dynamic systems, especially in the aircraft, military and aerospace field. In the 1960s, the major manufacturer was Electronic Associates of Princeton, New Jersey, with its 231R Analog Computer (vacuum tubes, 20 integrators) and subsequently its EAI 8800 Analog Computer (solid state operational amplifiers, 64 integrators). Its challenger was Applied Dynamics of Ann Arbor, Michigan. Although the basic technology for analog computers is usually operational amplifiers (also called "continuous current amplifiers" because they have no low frequency limitation), in the 1960s an attempt was made in the French ANALAC computer to use an alternative technology: medium frequency carrier and non dissipative reversible circuits. In the 1970s, every large company and administration concerned with problems in dynamics had an analog computing center, such as: • In the US: NASA (Huntsville, Houston), Martin Marietta (Orlando), Lockheed, Westinghouse, Hughes Aircraft • In Europe: CEA (French Atomic Energy Commission), MATRA, Aérospatiale, BAC (British Aircraft Corporation). Construction An analog computing machine consists of several main components: • Signal sources: These are blocks that generate analog signals, such as voltage or current, to represent input data and operations. • Amplifiers: Amplifiers are used to boost analog signals and maintain their amplitudes throughout the system. They amplify weak input signals and compensate for signal losses during transmission. • Filters: Filters are used to modify the spectrum of signals by suppressing or amplifying specific frequencies. They allow the isolation or suppression of certain signal components depending on the computational requirements. • Modulators and demodulators: Modulators convert information into analog signals that can be transmitted through a communication channel, and demodulators perform the reverse transformation, recovering the original data from modulated signals. • Adders, multipliers, log converters, and other calculation stages: These perform arithmetic operations on analog signals. They can be used for mathematical operations such as addition, multiplication, exponentiation, integration, and differentiation. • Storage and memory: Analog computing machines can use various forms of information storage, such as capacitors or inductors, to store intermediate results and memory. • Feedback and control: Feedback and control blocks are used to maintain the stability and accuracy of the analog computing machine. They may include regulation systems and error correction. • Patch panel: Analog computing machines also feature a patch panel or patch field. A patch panel is a physical structure on which connectors or contacts are placed to interconnect various components and modules within the system. On the patch panel, various connections and routes can be set and switched to configure the machine and determine signal flows. This allows users to flexibly configure and reconfigure the analog computing system to perform specific tasks. Patch panels are used to control data flows, connect and disconnect connections between various blocks of the system, including signal sources, amplifiers, filters, and other components. They provide convenience and flexibility in configuring and experimenting with analog computations. Patch panels can be presented as a physical panel with connectors or, in more modern systems, as a software interface that allows virtual management of signal connections and routes. • Hardware interfaces: Interfaces provide means of interaction with the machine, for example, for parameter control or data transmission. • Output device: this device is designed to present the results of analog computations in a convenient form for the user or to transmit the obtained data to other systems. Output devices in analog machines can vary depending on the specific goals of the system. For example, they could be graphical indicators, oscilloscopes, graphic recording devices, TV connection module, voltmeter, etc. These devices allow for the visualization of analog signals and the representation of the results of measurements or mathematical operations. • Power source and stabilizers. These are just general blocks that can be found in a typical analog computing machine. The actual configuration and components may vary depending on the specific implementation and the intended use of the machine. ==Analog–digital hybrids==

Analog computing devices are fast; digital computing devices are more versatile and accurate. The idea behind an analog-digital hybrid is to combine the two processes for the best efficiency. An example of such hybrid elementary device is the hybrid multiplier, where one input is an analog signal, the other input is a digital signal and the output is analog. It acts as an analog potentiometer, upgradable digitally. This kind of hybrid technique is mainly used for fast dedicated real time computation when computing time is very critical, as signal processing for radars and generally for controllers in embedded systems. In the early 1970s, analog computer manufacturers tried to tie together their analog computers with a digital computers to get the advantages of the two techniques. In such systems, the digital computer controlled the analog computer, providing initial set-up, initiating multiple analog runs, and automatically feeding and collecting data. The digital computer may also participate to the calculation itself using analog-to-digital and digital-to-analog converters. The largest manufacturer of hybrid computers was Electronic Associates. Their hybrid computer model 8900 was made of a digital computer and one or more analog consoles. These systems were mainly dedicated to large projects such as the Apollo program and Space Shuttle at NASA, or Ariane in Europe, especially during the integration step where at the beginning everything is simulated, and progressively real components replace their simulated parts. Only one company was known as offering general commercial computing services on its hybrid computers, CISI of France, in the 1970s. The best reference in this field is the 100,000 simulation runs for each certification of the automatic landing systems of Airbus and Concorde aircraft. After 1980, purely digital computers progressed more and more rapidly and were fast enough to compete with analog computers. One key to the speed of analog computers was their fully parallel computation, but this was also a limitation. The more equations required for a problem, the more analog components were needed, even when the problem wasn't time critical. "Programming" a problem meant interconnecting the analog operators; even with a removable wiring panel this was not very versatile. ==Implementations==

Mechanical analog computers 's tide-predicting machine of 1881–1882 Throughout history, many types of mechanical analog computers have been invented. These ranged from simple devices (like planimeters) to complex fire-control systems that guided WWII naval guns. Practical mechanical analog computers of any significant complexity used rotating shafts to carry variables from one mechanism to another. Cables and pulleys were used in a Fourier synthesizer, a tide-predicting machine, which summed the individual harmonic components. Another category, not nearly as well known, used rotating shafts only for input and output, with precision racks and pinions. The racks were connected to linkages that performed the computation. At least one U.S. Naval sonar fire control computer of the later 1950s, made by Librascope, was of this type, as was the principal computer in the Mk. 56 Gun Fire Control System. These computers often employed precision miter-gear differentials (pairs of bevel gears arranged to produce the sum or difference of two shaft rotations) to transmit variables between computing elements. The Ford Instrument Mark I Fire Control Computer, for example, contained approximately 160 miter-gear differentials. Integration with respect to another variable was done by a rotating disc driven by one variable. Output came from a pick-off device (such as a wheel) positioned at a radius on the disc proportional to the second variable. (A carrier with a pair of steel balls supported by small rollers worked especially well. A roller, its axis parallel to the disc's surface, provided the output. It was held against the pair of balls by a spring.) Arbitrary functions of one variable were provided by cams, with gearing to convert follower movement to shaft rotation. Functions of two variables were provided by three-dimensional cams. In one good design, one of the variables rotated the cam. A hemispherical follower moved its carrier on a pivot axis parallel to that of the cam's rotating axis. Pivoting motion was the output. The second variable moved the follower along the axis of the cam. One practical application was ballistics in gunnery. Coordinate conversion from polar to rectangular was done by a mechanical resolver (called a "component solver" in US Navy fire control computers). Two discs on a common axis positioned a sliding block with pin (stubby shaft) on it. One disc was a face cam, and a follower on the block in the face cam's groove set the radius. The other disc, closer to the pin, contained a straight slot in which the block moved. The input angle rotated the latter disc (the face cam disc, for an unchanging radius, rotated with the other (angle) disc; a differential and a few gears did this correction). Referring to the mechanism's frame, the location of the pin corresponded to the tip of the vector represented by the angle and magnitude inputs. Mounted on that pin was a square block. Rectilinear-coordinate outputs (both sine and cosine, typically) came from two slotted plates, each slot fitting on the block just mentioned. The plates moved in straight lines, the movement of one plate at right angles to that of the other. The slots were at right angles to the direction of movement. Each plate, by itself, was like a Scotch yoke, known to steam engine enthusiasts. During World War II, a similar mechanism converted rectilinear to polar coordinates, but it was not particularly successful and was eliminated in a significant redesign (USN, Mk. 1 to Mk. 1A). Multiplication was done by mechanisms based on the geometry of similar right triangles. Using the trigonometric terms for a right triangle, specifically opposite, adjacent, and hypotenuse, the adjacent side was fixed by construction. One variable changed the magnitude of the opposite side. In many cases, this variable changed sign; the hypotenuse could coincide with the adjacent side (a zero input), or move beyond the adjacent side, representing a sign change. Typically, a pinion-operated rack moving parallel to the (trig.-defined) opposite side would position a slide with a slot coincident with the hypotenuse. A pivot on the rack let the slide's angle change freely. At the other end of the slide (the angle, in trig. terms), a block on a pin fixed to the frame defined the vertex between the hypotenuse and the adjacent side. At any distance along the adjacent side, a line perpendicular to it intersects the hypotenuse at a particular point. The distance between that point and the adjacent side is some fraction that is the product of 1 the distance from the vertex, and 2 the magnitude of the opposite side. The second input variable in this type of multiplier positions a slotted plate perpendicular to the adjacent side. That slot contains a block, and that block's position in its slot is determined by another block right next to it. The latter slides along the hypotenuse, so the two blocks are positioned at a distance from the (trig.) adjacent side by an amount proportional to the product. To provide the product as an output, a third element, another slotted plate, also moves parallel to the (trig.) opposite side of the theoretical triangle. As usual, the slot is perpendicular to the direction of movement. A block in its slot, pivoted to the hypotenuse block positions it. A special type of integrator, used at a point where only moderate accuracy was needed, was based on a steel ball, instead of a disc. It had two inputs, one to rotate the ball, and the other to define the angle of the ball's rotating axis. That axis was always in a plane that contained the axes of two movement pick-off rollers, quite similar to the mechanism of a rolling-ball computer mouse (in that mechanism, the pick-off rollers were roughly the same diameter as the ball). The pick-off roller axes were at right angles. A pair of rollers "above" and "below" the pick-off plane were mounted in rotating holders that were geared together. That gearing was driven by the angle input, and established the rotating axis of the ball. The other input rotated the "bottom" roller to make the ball rotate. Essentially, the whole mechanism, called a component integrator, was a variable-speed drive with one motion input and two outputs, as well as an angle input. The angle input varied the ratio (and direction) of coupling between the "motion" input and the outputs according to the sine and cosine of the input angle. Although they did not accomplish any computation, electromechanical position servos (aka. torque amplifiers) were essential in mechanical analog computers of the "rotating-shaft" type for providing operating torque to the inputs of subsequent computing mechanisms, as well as driving output data-transmission devices such as large torque-transmitter synchros in naval computers. Other readout mechanisms, not directly part of the computation, included internal odometer-like counters with interpolating drum dials for indicating internal variables, and mechanical multi-turn limit stops. Considering that accurately controlled rotational speed in analog fire-control computers was a basic element of their accuracy, there was a motor with its average speed controlled by a balance wheel, hairspring, jeweled-bearing differential, a twin-lobe cam, and spring-loaded contacts (ship's AC power frequency was not necessarily accurate, nor dependable enough, when these computers were designed). Electronic analog computers Electronic analog computers typically have front panels with numerous jacks (single-contact sockets) that permit patch cords (flexible wires with plugs at both ends) to create the interconnections that define the problem setup. In addition, there are precision high-resolution potentiometers (variable resistors) for setting up (and, when needed, varying) scale factors. In addition, there is usually a zero-center analog pointer-type meter for modest-accuracy voltage measurement. Stable, accurate voltage sources provide known magnitudes. Typical electronic analog computers contain anywhere from a few to a hundred or more operational amplifiers ("op amps"), named because they perform mathematical operations. Op amps are a particular type of feedback amplifier with very high gain and stable input (low and stable offset). They are always used with precision feedback components that, in operation, all but cancel out the currents arriving from input components. The majority of op amps in a representative setup are summing amplifiers, which add and subtract analog voltages, providing the result at their output jacks. As well, op amps with capacitor feedback are usually included in a setup; they integrate the sum of their inputs with respect to time. Integrating with respect to another variable is the nearly exclusive province of mechanical analog integrators; it is almost never done in electronic analog computers. However, given that a problem solution does not change with time, time can serve as one of the variables. Other computing elements include analog multipliers, nonlinear function generators, and analog comparators. Electrical elements such as inductors and capacitors used in electrical analog computers had to be carefully manufactured to reduce non-ideal effects. For example, in the construction of AC power network analyzers, one motive for using higher frequencies for the calculator (instead of the actual power frequency) was that higher-quality inductors could be more easily made. Many general-purpose analog computers avoided the use of inductors entirely, re-casting the problem in a form that could be solved using only resistive and capacitive elements, since high-quality capacitors are relatively easy to make. The use of electrical properties in analog computers means that calculations are normally performed in real time (or faster), at a speed determined mostly by the frequency response of the operational amplifiers and other computing elements. In the history of electronic analog computers, there were some special high-speed types. Nonlinear functions and calculations can be constructed to a limited precision (three or four digits) by designing function generators—special circuits of various combinations of resistors and diodes to provide the nonlinearity. Typically, as the input voltage increases, progressively more diodes conduct. When compensated for temperature, the forward voltage drop of a transistor's base-emitter junction can provide a usably accurate logarithmic or exponential function. Op amps scale the output voltage so that it is usable with the rest of the computer. Any physical process that models some computation can be interpreted as an analog computer. Some examples, invented for the purpose of illustrating the concept of analog computation, include using a bundle of spaghetti as a model of sorting numbers; a board, a set of nails, and a rubber band as a model of finding the convex hull of a set of points; and strings tied together as a model of finding the shortest path in a network. These are all described in Dewdney (1984). ==Components==

s and is currently housed at the Cambridge Museum of Technology. Analog computers often have a complicated framework, but they have, at their core, a set of key components that perform the calculations. The operator manipulates these through the computer's framework. Key hydraulic components might include pipes, valves and containers. Key mechanical components might include rotating shafts for carrying data within the computer, miter gear differentials, disc/ball/roller integrators, cams (2-D and 3-D), mechanical resolvers and multipliers, and torque servos. Key electrical/electronic components might include: • precision resistors and capacitors • operational amplifiers • multipliers • potentiometers • fixed-function generators The core mathematical operations used in an electric analog computer are: • addition • integration with respect to time • inversion • multiplication • exponentiation • logarithm • division In some analog computer designs, multiplication is much preferred to division. Division is carried out with a multiplier in the feedback path of an Operational Amplifier. Differentiation with respect to time is not frequently used, and in practice is avoided by redefining the problem when possible. It corresponds in the frequency domain to a high-pass filter, which means that high-frequency noise is amplified; differentiation also risks instability. ==Limitations==

In general, analog computers are limited by non-ideal effects. An analog signal is composed of four basic components: DC and AC magnitudes, frequency, and phase. The real limits of range on these characteristics limit analog computers. Some of these limits include the operational amplifier offset, finite gain, and frequency response, noise floor, non-linearities, temperature coefficient, and parasitic effects within semiconductor devices. For commercially available electronic components, ranges of these aspects of input and output signals are always figures of merit. ==Decline==

In the 1950s to 1970s, digital computers based on first vacuum tubes, transistors, integrated circuits and then micro-processors became more economical and precise. This led digital computers to largely replace analog computers. Even so, some research in analog computation is still being done. A few universities still use analog computers to teach control system theory. The American company Comdyna manufactured small analog computers. At Indiana University Bloomington, Jonathan Mills has developed the Extended Analog Computer based on sampling voltages in a foam sheet. At the Harvard Robotics Laboratory, analog computation is a research topic. Lyric Semiconductor's error correction circuits use analog probabilistic signals. Slide rules are still used as flight computers in flight training. ==Resurgence==

With the development of very-large-scale integration (VLSI) technology, Yannis Tsividis' group at Columbia University has been revisiting analog/hybrid computers design in standard CMOS process. Two VLSI chips have been developed, an 80th-order analog computer (250 nm) by Glenn Cowan in 2005 and a 4th-order hybrid computer (65 nm) developed by Ning Guo in 2015, both targeting at energy-efficient ODE/PDE applications. Glenn's chip contains 16 macros, in which there are 25 analog computing blocks, namely integrators, multipliers, fanouts, few nonlinear blocks. Ning's chip contains one macro block, in which there are 26 computing blocks including integrators, multipliers, fanouts, ADCs, SRAMs and DACs. Arbitrary nonlinear function generation is made possible by the ADC+SRAM+DAC chain, where the SRAM block stores the nonlinear function data. The experiments from the related publications revealed that VLSI analog/hybrid computers demonstrated about 1–2 orders magnitude of advantage in both solution time and energy while achieving accuracy within 5%, which points to the promise of using analog/hybrid computing techniques in the area of energy-efficient approximate computing. In 2016, a team of researchers developed a compiler to solve differential equations using analog circuits. Analog computers are also used in neuromorphic computing, and in 2021 a group of researchers have shown that a specific type of artificial neural network called a spiking neural network was able to work with analog neuromorphic computers. In 2021, the German company anabrid GmbH began to produce THE ANALOG THING (abbreviated THAT), a small low-cost analog computer mainly for educational and scientific use. The company is also constructing analog mainframes and hybrid computers. ==Practical examples==

simulator analog computer (also note slide rule on desk) These are examples of analog computers that have been constructed or practically used: • Boeing B-29 Superfortress Central Fire Control System • Deltar • E6B flight computer • Ishiguro Storm Surge Computer • Kerrison Predictor • Leonardo Torres y Quevedo's Analogue Calculating Machines based on "fusee sans fin" • Librascope, aircraft weight and balance computer • Mechanical computer • Mechanical watch • Mechanical integrators, for example, the planimeter • Mischgerät (V-2 guidance computer) • MONIAC, economic modelling • Nomogram • Norden bombsight • Rangekeeper, and related fire control computers • Scanimate • SR-71 inlet control system (fast adjustment of inlet geometry to prevent super-sonic shock waves from causing engine flame-out at high mach numbers) • THE ANALOG THING, a small analog computer by anabrid • Torpedo Data Computer • Torquetum • Water integrator Analog (audio) synthesizers can also be viewed as a form of analog computer, and their technology was originally based in part on electronic analog computer technology. The ARP 2600's Ring Modulator was actually a moderate-accuracy analog multiplier. The Simulation Council (or Simulations Council) was an association of analog computer users in US. It is now known as The Society for Modeling and Simulation International. The Simulation Council newsletters from 1952 to 1963 are available online and show the concerns and technologies at the time, and the common use of analog computers for missilry. ==See also==