Atmospheric entry

s of high speed wind tunnel tests The concept of the ablative heat shield was described as early as 1920 by Robert Goddard: "In the case of meteors, which enter the atmosphere with speeds as high as per second, the interior of the meteors remains cold, and the erosion is due, to a large extent, to chipping or cracking of the suddenly heated surface. For this reason, if the outer surface of the apparatus were to consist of layers of a very infusible hard substance with layers of a poor heat conductor between, the surface would not be eroded to any considerable extent, especially as the velocity of the apparatus would not be nearly so great as that of the average meteor." Practical development of reentry systems began as the range, and reentry velocity of ballistic missiles increased. For early short-range missiles, like the V-2, stabilization and aerodynamic stress were important issues (many V-2s broke apart during reentry), but heating was not a serious problem. Medium-range missiles like the Soviet R-5, with a range, required ceramic composite heat shielding on separable reentry vehicles (it was no longer possible for the entire rocket structure to survive reentry). The first ICBMs, with ranges of , were only possible with the development of modern ablative heat shields and blunt-shaped vehicles. In the United States, this technology was pioneered by H. Julian Allen and A. J. Eggers Jr. of the National Advisory Committee for Aeronautics (NACA) at Ames Research Center. In 1951, they made the counterintuitive discovery that a blunt shape (high drag) made the most effective heat shield. From simple engineering principles, Allen and Eggers showed that the heat load experienced by an entry vehicle was inversely proportional to the drag coefficient; i.e., the greater the drag, the less the heat load. If the reentry vehicle is made blunt, air cannot "get out of the way" quickly enough, and acts as an air cushion to push the shock wave and heated shock layer forward (away from the vehicle). Since most of the hot gases are no longer in direct contact with the vehicle, the heat energy would stay in the shocked gas and simply move around the vehicle to later dissipate into the atmosphere. The Allen and Eggers discovery, though initially treated as a military secret, was eventually published in 1958. ==Terminology, definitions and jargon==

reentry profile When atmospheric entry is part of a spacecraft landing or recovery, particularly on a planetary body other than Earth, entry is part of a phase referred to as entry, descent, and landing, or EDL. When the atmospheric entry returns to the same body that the vehicle had launched from, the event is referred to as reentry (almost always referring to Earth entry). The fundamental design objective in atmospheric entry of a spacecraft is to dissipate the energy of a spacecraft that is traveling at hypersonic speed as it enters an atmosphere such that equipment, cargo, and any passengers are slowed and land near a specific destination on the surface at zero velocity while keeping stresses on the spacecraft and any passengers within acceptable limits. This may be accomplished by propulsive or aerodynamic (vehicle characteristics or parachute) means, or by some combination. ==Entry vehicle shapes==

There are several basic shapes used in designing entry vehicles: Sphere or spherical section flying with the blunt end of the heat shield at a non-zero angle of attack in order to establish a lifting entry and control the landing site (artistic rendition) The simplest axisymmetric shape is the sphere or spherical section. This can either be a complete sphere or a spherical section forebody with a converging conical afterbody. The aerodynamics of a sphere or spherical section are easy to model analytically using Newtonian impact theory. Likewise, the spherical section's heat flux can be accurately modeled with the Fay–Riddell equation. The static stability of a spherical section is assured if the vehicle's center of mass is upstream from the center of curvature (dynamic stability is more problematic). Pure spheres have no lift. However, by flying at an angle of attack, a spherical section has modest aerodynamic lift thus providing some cross-range capability and widening its entry corridor. In the late 1950s and early 1960s, high-speed computers were not yet available and computational fluid dynamics was still embryonic. Because the spherical section was amenable to closed-form analysis, that geometry became the default for conservative design. Consequently, crewed capsules of that era were based upon the spherical section. Pure spherical entry vehicles were used in the early Soviet Vostok and Voskhod capsules and in Soviet Mars and Venera descent vehicles. The Apollo command module used a spherical section forebody heat shield with a converging conical afterbody. It flew a lifting entry with a hypersonic trim angle of attack of −27° (0° is blunt-end first) to yield an average L/D (lift-to-drag ratio) of 0.368. The resultant lift achieved a measure of cross-range control by offsetting the vehicle's center of mass from its axis of symmetry, allowing the lift force to be directed left or right by rolling the capsule on its longitudinal axis. Other examples of the spherical section geometry in crewed capsules are Soyuz/Zond, Gemini, and Mercury. Even these small amounts of lift allow trajectories that have very significant effects on peak g-force, reducing it from 8–9 g for a purely ballistic (slowed only by drag) trajectory to 4–5 g, as well as greatly reducing the peak reentry heat. Sphere-cone The sphere-cone is a spherical section with a frustum or blunted cone attached. The sphere-cone's dynamic stability is typically better than that of a spherical section. The vehicle enters sphere-first. With a sufficiently small half-angle and properly placed center of mass, a sphere-cone can provide aerodynamic stability from Keplerian entry to surface impact. (The half-angle is the angle between the cone's axis of rotational symmetry and its outer surface, and thus half the angle made by the cone's surface edges.) The original American sphere-cone aeroshell was the Mk-2 RV (reentry vehicle), which was developed in 1955 by the General Electric Corp. The Mk-2's design was derived from blunt-body theory and used a radiatively cooled thermal protection system (TPS) based upon a metallic heat shield (the different TPS types are later described in this article). The Mk-2 had significant defects as a weapon delivery system, i.e., it loitered too long in the upper atmosphere due to its lower ballistic coefficient and also trailed a stream of vaporized metal making it very visible to radar. These defects made the Mk-2 overly susceptible to anti-ballistic missile (ABM) systems. Consequently, an alternative sphere-cone RV to the Mk-2 was developed by General Electric. RV, Cold War weapon and ancestor to most of the U.S. missile entry vehicles This new RV was the Mk-6 which used a non-metallic ablative TPS, a nylon phenolic. This new TPS was so effective as a reentry heat shield that significantly reduced bluntness was possible. However, the Mk-6 was a huge RV with an entry mass of 3,360 kg, a length of 3.1 m and a half-angle of 12.5°. Subsequent advances in nuclear weapon and ablative TPS design allowed RVs to become significantly smaller with a further reduced bluntness ratio compared to the Mk-6. Since the 1960s, the sphere-cone has become the preferred geometry for modern ICBM RVs with typical half-angles being between 10° and 11°. during final assembly Reconnaissance satellite RVs (recovery vehicles) also used a sphere-cone shape and were the first American example of a non-munition entry vehicle (Discoverer-I, launched on 28 February 1959). The sphere-cone was later used for space exploration missions to other celestial bodies or for return from open space; e.g., Stardust probe. Unlike with military RVs, the advantage of the blunt body's lower TPS mass remained with space exploration entry vehicles like the Galileo Probe with a half-angle of 45° or the Viking aeroshell with a half-angle of 70°. Space exploration sphere-cone entry vehicles have landed on the surface or entered the atmospheres of Mars, Venus, Jupiter, and Titan. Biconic , shown during its first flight, was a prototype single-stage-to-orbit vehicle, and used a biconic shape similar to AMaRV. The biconic is a sphere-cone with an additional frustum attached. The biconic offers a significantly improved L/D ratio. A biconic designed for Mars aerocapture typically has an L/D of approximately 1.0 compared to an L/D of 0.368 for the Apollo-CM. The higher L/D makes a biconic shape better suited for transporting people to Mars due to the lower peak deceleration. Arguably, the most significant biconic ever flown was the Advanced Maneuverable Reentry Vehicle (AMaRV). Four AMaRVs were made by the McDonnell Douglas Corp. and represented a significant leap in RV sophistication. Three AMaRVs were launched by Minuteman-1 ICBMs on 20 December 1979, 8 October 1980 and 4 October 1981. AMaRV had an entry mass of approximately 470 kg, a nose radius of 2.34 cm, a forward-frustum half-angle of 10.4°, an inter-frustum radius of 14.6 cm, aft-frustum half-angle of 6°, and an axial length of 2.079 meters. No accurate diagram or picture of AMaRV has ever appeared in the open literature. However, a schematic sketch of an AMaRV-like vehicle along with trajectory plots showing hairpin turns has been published. AMaRV's attitude was controlled through a split body flap (also called a split-windward flap) along with two yaw flaps mounted on the vehicle's sides. Hydraulic actuation was used for controlling the flaps. AMaRV was guided by a fully autonomous navigation system designed for evading anti-ballistic missile (ABM) interception. The McDonnell Douglas DC-X (also a biconic) was essentially a scaled-up version of AMaRV. AMaRV and the DC-X also served as the basis for an unsuccessful proposal for what eventually became the Lockheed Martin X-33. Non-axisymmetric shapes Non-axisymmetric shapes have been used for crewed entry vehicles. One example is the winged orbit vehicle that uses a delta wing for maneuvering during descent much like a conventional glider. This approach has been used by the American Space Shuttle, the Soviet Buran and the in-development Starship. The lifting body is another entry vehicle geometry and was used with the X-23 PRIME (Precision Recovery Including Maneuvering Entry) vehicle. ==Entry heating==

trail of Gemini 2 reentry Objects entering an atmosphere from space at high velocities relative to the atmosphere will cause very high levels of heating. Atmospheric entry heating comes principally from two sources: • convection of hot gas flow past the surface of the body and catalytic chemical recombination reactions between the surface and atmospheric gases; and • radiation from the energetic shock layer that forms in the front and sides of the body During certain intensity of ionization, a radio-blackout with the spacecraft is produced. While NASA's Earth entry interface is at , the main heating during controlled entry takes place at altitudes of , peaking at . Shock layer gas physics At typical reentry temperatures, the air in the shock layer is both ionized and dissociated. This chemical dissociation necessitates various physical models to describe the shock layer's thermal and chemical properties. There are four basic physical models of a gas that are important to aeronautical engineers who design heat shields: Perfect gas model Almost all aeronautical engineers are taught the perfect (ideal) gas model during their undergraduate education. Most of the important perfect gas equations along with their corresponding tables and graphs are shown in NACA Report 1135. Excerpts from NACA Report 1135 often appear in the appendices of thermodynamics textbooks and are familiar to most aeronautical engineers who design supersonic aircraft. The perfect gas theory is elegant and extremely useful for designing aircraft but assumes that the gas is chemically inert. From the standpoint of aircraft design, air can be assumed to be inert for temperatures less than at one atmosphere pressure. The perfect gas theory begins to break down at 550 K and is not usable at temperatures greater than . For temperatures greater than 2,000 K, a heat shield designer must use a real gas model. Real (equilibrium) gas model An entry vehicle's pitching moment can be significantly influenced by real-gas effects. Both the Apollo command module and the Space Shuttle were designed using incorrect pitching moments determined through inaccurate real-gas modelling. The Apollo-CM's trim-angle angle of attack was higher than originally estimated, resulting in a narrower lunar return entry corridor. The actual aerodynamic center of the Columbia was upstream from the calculated value due to real-gas effects. On Columbias maiden flight (STS-1), astronauts John Young and Robert Crippen had some anxious moments during reentry when there was concern about losing control of the vehicle. An equilibrium real-gas model assumes that a gas is chemically reactive, but also assumes all chemical reactions have had time to complete and all components of the gas have the same temperature (this is called thermodynamic equilibrium). When air is processed by a shock wave, it is superheated by compression and chemically dissociates through many different reactions. Direct friction upon the reentry object is not the main cause of shock-layer heating. It is caused mainly from isentropic heating of the air molecules within the compression wave. Friction based entropy increases of the molecules within the wave also account for some heating. The distance from the shock wave to the stagnation point on the entry vehicle's leading edge is called shock wave stand off. An approximate rule of thumb for shock wave standoff distance is 0.14 times the nose radius. One can estimate the time of travel for a gas molecule from the shock wave to the stagnation point by assuming a free stream velocity of 7.8 km/s and a nose radius of 1 meter, i.e., time of travel is about 18 microseconds. This is roughly the time required for shock-wave-initiated chemical dissociation to approach chemical equilibrium in a shock layer for a 7.8 km/s entry into air during peak heat flux. Consequently, as air approaches the entry vehicle's stagnation point, the air effectively reaches chemical equilibrium thus enabling an equilibrium model to be usable. For this case, most of the shock layer between the shock wave and leading edge of an entry vehicle is chemically reacting and not in a state of equilibrium. The Fay–Riddell equation, The Lighthill–Freeman model initially assumes a gas made up of a single diatomic species susceptible to only one chemical formula and its reverse; e.g., N2 = N + N and N + N = N2 (dissociation and recombination). Because of its simplicity, the Lighthill–Freeman model is a useful pedagogical tool, but is too simple for modelling non-equilibrium air. Air is typically assumed to have a mole fraction composition of 0.7812 molecular nitrogen, 0.2095 molecular oxygen and 0.0093 argon. The simplest real gas model for air is the five species model, which is based upon N2, O2, NO, N, and O. The five species model assumes no ionization and ignores trace species like carbon dioxide. When running a Gibbs free energy equilibrium program, the iterative process from the originally specified molecular composition to the final calculated equilibrium composition is essentially random and not time accurate. With a non-equilibrium program, the computation process is time accurate and follows a solution path dictated by chemical and reaction rate formulas. The five species model has 17 chemical formulas (34 when counting reverse formulas). The Lighthill–Freeman model is based upon a single ordinary differential equation and one algebraic equation. The five species model is based upon five ordinary differential equations and 17 algebraic equations. Because the five ordinary differential equations are tightly coupled, the system is numerically "stiff" and difficult to solve. The five species model is only usable for entry from low Earth orbit where entry velocity is approximately . For lunar return entry of 11 km/s, the shock layer contains a significant amount of ionized nitrogen and oxygen. The five-species model is no longer accurate and a twelve-species model must be used instead. Atmospheric entry interface velocities on a Mars–Earth trajectory are on the order of . Modeling high-speed Mars atmospheric entry—which involves a carbon dioxide, nitrogen and argon atmosphere—is even more complex requiring a 19-species model. An important aspect of modelling non-equilibrium real gas effects is radiative heat flux. If a vehicle is entering an atmosphere at very high speed (hyperbolic trajectory, lunar return) and has a large nose radius then radiative heat flux can dominate TPS heating. Radiative heat flux during entry into an air or carbon dioxide atmosphere typically comes from asymmetric diatomic molecules; e.g., cyanogen (CN), carbon monoxide, nitric oxide (NO), single ionized molecular nitrogen etc. These molecules are formed by the shock wave dissociating ambient atmospheric gas followed by recombination within the shock layer into new molecular species. The newly formed diatomic molecules initially have a very high vibrational temperature that efficiently transforms the vibrational energy into radiant energy; i.e., radiative heat flux. The whole process takes place in less than a millisecond which makes modelling a challenge. The experimental measurement of radiative heat flux (typically done with shock tubes) along with theoretical calculation through the unsteady Schrödinger equation are among the more esoteric aspects of aerospace engineering. Most of the aerospace research work related to understanding radiative heat flux was done in the 1960s, but largely discontinued after conclusion of the Apollo Program. Radiative heat flux in air was just sufficiently understood to ensure Apollo's success. However, radiative heat flux in carbon dioxide (Mars entry) is still barely understood and will require major research. Frozen gas model The frozen gas model describes a special case of a gas that is not in equilibrium. The name "frozen gas" can be misleading. A frozen gas is not "frozen" like ice is frozen water. Rather a frozen gas is "frozen" in time (all chemical reactions are assumed to have stopped). Chemical reactions are normally driven by collisions between molecules. If gas pressure is slowly reduced such that chemical reactions can continue then the gas can remain in equilibrium. However, it is possible for gas pressure to be so suddenly reduced that almost all chemical reactions stop. For that situation the gas is considered frozen. The distinction between equilibrium and frozen is important because it is possible for a gas such as air to have significantly different properties (speed-of-sound, viscosity etc.) for the same thermodynamic state; e.g., pressure and temperature. Frozen gas can be a significant issue in the wake behind an entry vehicle. During reentry, free stream air is compressed to high temperature and pressure by the entry vehicle's shock wave. Non-equilibrium air in the shock layer is then transported past the entry vehicle's leading side into a region of rapidly expanding flow that causes freezing. The frozen air can then be entrained into a trailing vortex behind the entry vehicle. Correctly modelling the flow in the wake of an entry vehicle is very difficult. Thermal protection shield (TPS) heating in the vehicle's afterbody is usually not very high, but the geometry and unsteadiness of the vehicle's wake can significantly influence aerodynamics (pitching moment) and particularly dynamic stability. ==Thermal protection systems==

A thermal protection system, or TPS, is the barrier that protects a spacecraft during the searing heat of atmospheric reentry. Multiple approaches for the thermal protection of spacecraft are in use, among them ablative heat shields, passive cooling, and active cooling of spacecraft surfaces. In general they can be divided into two categories: ablative TPS and reusable TPS. Ablative TPS are required when space craft reach a relatively low altitude before slowing down. Spacecraft like the space shuttle are designed to slow down at high altitude so that they can use reuseable TPS. (see: Space Shuttle thermal protection system). Thermal protection systems are tested in high enthalpy ground testing or plasma wind tunnels that reproduce the combination of high enthalpy and high stagnation pressure using Induction plasma or DC plasma. Ablative capsule The ablative heat shield functions by lifting the hot shock layer gas away from the heat shield's outer wall (creating a cooler boundary layer). The boundary layer comes from blowing of gaseous reaction products from the heat shield material and provides protection against all forms of heat flux. The overall process of reducing the heat flux experienced by the heat shield's outer wall by way of a boundary layer is called blockage. Ablation occurs at two levels in an ablative TPS: the outer surface of the TPS material chars, melts, and sublimes, while the bulk of the TPS material undergoes pyrolysis and expels product gases. The gas produced by pyrolysis is what drives blowing and causes blockage of convective and catalytic heat flux. Pyrolysis can be measured in real time using thermogravimetric analysis, so that the ablative performance can be evaluated. Ablation can also provide blockage against radiative heat flux by introducing carbon into the shock layer thus making it optically opaque. Radiative heat flux blockage was the primary thermal protection mechanism of the Galileo Probe TPS material (carbon phenolic). Early research on ablation technology in the United States was centered at NASA's Ames Research Center located at Moffett Field, California. Ames Research Center was ideal, since it had numerous wind tunnels capable of generating varying wind velocities. Initial experiments typically mounted a mock-up of the ablative material to be analyzed within a hypersonic wind tunnel. Testing of ablative materials occurs at the Ames Arc Jet Complex. Many spacecraft thermal protection systems have been tested in this facility, including the Apollo, Space Shuttle, and Orion heat shield materials. '' during final assembly showing the aeroshell, cruise ring and solid rocket motor Carbon phenolic Carbon phenolic was originally developed as a rocket nozzle throat material (used in the Space Shuttle Solid Rocket Booster) and for reentry-vehicle nose tips. The thermal conductivity of a particular TPS material is usually proportional to the material's density. Carbon phenolic is a very effective ablative material, but also has high density which is undesirable. The NASA Galileo Probe used carbon phenolic for its TPS material. If the heat flux experienced by an entry vehicle is insufficient to cause pyrolysis then the TPS material's conductivity could allow heat flux conduction into the TPS bondline material thus leading to TPS failure. Consequently, for entry trajectories causing lower heat flux, carbon phenolic is sometimes inappropriate and lower-density TPS materials such as the following examples can be better design choices: Super light-weight ablator SLA in SLA-561V stands for super light-weight ablator. SLA-561V is a proprietary ablative made by Lockheed Martin that has been used as the primary TPS material on all of the 70° sphere-cone entry vehicles sent by NASA to Mars other than the Mars Science Laboratory (MSL). SLA-561V begins significant ablation at a heat flux of approximately 110 W/cm2, but will fail for heat fluxes greater than 300 W/cm2. The MSL aeroshell TPS is currently designed to withstand a peak heat flux of 234 W/cm2. The peak heat flux experienced by the Viking 1 aeroshell which landed on Mars was 21 W/cm2. For Viking 1, the TPS acted as a charred thermal insulator and never experienced significant ablation. Viking 1 was the first Mars lander and based upon a very conservative design. The Viking aeroshell had a base diameter of 3.54 meters (the largest used on Mars until Mars Science Laboratory). SLA-561V is applied by packing the ablative material into a honeycomb core that is pre-bonded to the aeroshell's structure thus enabling construction of a large heat shield. Phenolic-impregnated carbon ablator Sample return capsule at USAF Utah Range.|left Phenolic-impregnated carbon ablator (PICA) is a carbon fiber preform impregnated in phenolic resin. It has the advantages of low density (much lighter than carbon phenolic) coupled with efficient ablative ability at high heat flux. It is a good choice for ablative applications such as high-peak-heating conditions found on sample-return missions or lunar-return missions. PICA's thermal conductivity is lower than other high-heat-flux-ablative materials, such as conventional carbon phenolics. PICA was patented by NASA Ames Research Center in the 1990s and was the primary TPS material for the Stardust aeroshell. The Stardust sample-return capsule was the fastest man-made object ever to reenter Earth's atmosphere, at 28,000 mph (ca. 12.5 km/s) at 135 km altitude. This was faster than the Apollo mission capsules and 70% faster than the Shuttle. PICA was critical for the viability of the Stardust mission, which returned to Earth in 2006. Stardust's heat shield (0.81 m base diameter) was made of one monolithic piece sized to withstand a nominal peak heating rate of 1.2 kW/cm2. A PICA heat shield was also used for the Mars Science Laboratory entry into the Martian atmosphere. The first reentry test of a PICA-X heat shield was on the Dragon C1 mission on 8 December 2010. The PICA-X heat shield was designed, developed and fully qualified by a small team of a dozen engineers and technicians in less than four years. PICA-X is ten times less expensive to manufacture than the NASA PICA heat shield material. PICA-3 A second enhanced version of PICA—called PICA-3—was developed by SpaceX during the mid-2010s. It was first flight tested on the Crew Dragon spacecraft in 2019 during the flight demonstration mission, in April 2019, and put into regular service on that spacecraft in 2020. HARLEM PICA and most other ablative TPS materials are either proprietary or classified, with formulations and manufacturing processes not disclosed in the open literature. This limits the ability of researchers to study these materials and hinders the development of thermal protection systems. Thus, the High Enthalpy Flow Diagnostics Group (HEFDiG) at the University of Stuttgart has developed an open carbon-phenolic ablative material, called the HEFDiG Ablation-Research Laboratory Experiment Material (HARLEM), from commercially available materials. HARLEM is prepared by impregnating a preform of a carbon fiber porous monolith (such as Calcarb rigid carbon insulation) with a solution of resole phenolic resin and polyvinylpyrrolidone in ethylene glycol, heating to polymerize the resin and then removing the solvent under vacuum. The resulting material is cured and machined to the desired shape. SIRCA impactor aeroshell, a classic 45° sphere-cone with spherical section afterbody, enabling aerodynamic stability from atmospheric entry to surface impact Silicone-impregnated reusable ceramic ablator (SIRCA) was also developed at NASA Ames Research Center and was used on the Backshell Interface Plate (BIP) of the Mars Pathfinder and Mars Exploration Rover (MER) aeroshells. The BIP was at the attachment points between the aeroshell's backshell (also called the afterbody or aft cover) and the cruise ring (also called the cruise stage). SIRCA was also the primary TPS material for the unsuccessful Deep Space 2 (DS/2) Mars impactor probes with their aeroshells. SIRCA is a monolithic, insulating material that can provide thermal protection through ablation. It is the only TPS material that can be machined to custom shapes and then applied directly to the spacecraft. There is no post-processing, heat treating, or additional coatings required (unlike Space Shuttle tiles). Since SIRCA can be machined to precise shapes, it can be applied as tiles, leading edge sections, full nose caps, or in any number of custom shapes or sizes. , SIRCA had been demonstrated in backshell interface applications, but not yet as a forebody TPS material. AVCOAT AVCOAT is composed of silica fibers in an epoxy novolac resin. It is used in the design of several ablative heat shields. NASA originally used it for the Apollo command module in the 1960s, and then utilized the material for its next-generation beyond low Earth orbit Orion crew module, which first flew in a December 2014 test and then operationally in November 2022. The Avcoat to be used on Orion has been reformulated to meet environmental legislation that has been passed since the end of Apollo. Thermal soak Thermal soak is a part of almost all TPS schemes. For example, an ablative heat shield loses most of its thermal protection effectiveness when the outer wall temperature drops below the minimum necessary for pyrolysis. From that time to the end of the heat pulse, heat from the shock layer convects into the heat shield's outer wall and would eventually conduct to the payload. This outcome can be prevented by ejecting the heat shield (with its heat soak) prior to the heat conducting to the inner wall. Refractory insulation takes a close look at TPS tiles underneath Space Shuttle Atlantis. tiles were used on the Space Shuttle. Refractory insulation keeps the heat in the outermost layer of the spacecraft surface, where it is conducted away by the air. The temperature of the surface rises to incandescent levels, so the material must have a very high melting point, and the material must also exhibit very low thermal conductivity. Materials with these properties tend to be brittle, delicate, and difficult to fabricate in large sizes, so they are generally fabricated as relatively small tiles that are then attached to the structural skin of the spacecraft. There is a tradeoff between toughness and thermal conductivity: less conductive materials are generally more brittle. The space shuttle used multiple types of tiles. Tiles are also used on the Boeing X-37, Dream Chaser, and Starship's upper stage. Because insulation cannot be perfect, some heat energy is stored in the insulation and in the underlying material ("thermal soaking") and must be dissipated after the spacecraft exits the high-temperature flight regime. Some of this heat will re-radiate through the surface or will be carried off the surface by convection, but some will heat the spacecraft structure and interior, which may require active cooling after landing. Passively cooled ) originally used a radiatively cooled TPS, but was later converted to an ablative TPS. In some early ballistic missile RVs (e.g., the Mk-2 and the sub-orbital Mercury spacecraft), radiatively cooled TPS were used to initially absorb heat flux during the heat pulse, and, then, after the heat pulse, radiate and convect the stored heat back into the atmosphere. However, the earlier version of this technique required a considerable quantity of metal TPS (e.g., titanium, beryllium, copper, etc.). Modern designers prefer to avoid this added mass by using ablative and thermal-soak TPS instead. Thermal protection systems relying on emissivity use high emissivity coatings (HECs) to facilitate radiative cooling, while an underlying porous ceramic layer serves to protect the structure from high surface temperatures. High thermally stable emissivity values coupled with low thermal conductivity are key to the functionality of such systems. Radiatively cooled TPS can be found on modern entry vehicles, but reinforced carbon–carbon (RCC) (also called carbon–carbon) is normally used instead of metal. RCC was the TPS material on the Space Shuttle's nose cone and wing leading edges, and was also proposed as the leading-edge material for the X-33. Carbon is the most refractory material known, with a one-atmosphere sublimation temperature of for graphite. This high temperature made carbon an obvious choice as a radiatively cooled TPS material. Disadvantages of RCC are that it is currently expensive to manufacture, is heavy, and lacks robust impact resistance. Some high-velocity aircraft, such as the SR-71 Blackbird and Concorde, deal with heating similar to that experienced by spacecraft, but at much lower intensity, and for hours at a time. Studies of the SR-71's titanium skin revealed that the metal structure was restored to its original strength through annealing due to aerodynamic heating. In the case of the Concorde, the aluminium nose was permitted to reach a maximum operating temperature of (approximately warmer than the normally sub-zero, ambient air); the metallurgical implications (loss of temper) that would be associated with a higher peak temperature were the most significant factors determining the top speed of the aircraft. A radiatively cooled TPS for an entry vehicle is often called a hot-metal TPS. Early TPS designs for the Space Shuttle called for a hot-metal TPS based upon a nickel superalloy (dubbed René 41) and titanium shingles. This Shuttle TPS concept was rejected, because it was believed a silica tile-based TPS would involve lower development and manufacturing costs. A nickel superalloy-shingle TPS was again proposed for the unsuccessful X-33 single-stage-to-orbit (SSTO) prototype. Recently, newer radiatively cooled TPS materials have been developed that could be superior to RCC. Known as Ultra-High Temperature Ceramics, they were developed for the prototype vehicle Slender Hypervelocity Aerothermodynamic Research Probe (SHARP). These TPS materials are based on zirconium diboride and hafnium diboride. SHARP TPS have suggested performance improvements allowing for sustained Mach 7 flight at sea level, Mach 11 flight at altitudes, and significant improvements for vehicles designed for continuous hypersonic flight. SHARP TPS materials enable sharp leading edges and nose cones to greatly reduce drag for airbreathing combined-cycle-propelled spaceplanes and lifting bodies. SHARP materials have exhibited effective TPS characteristics from zero to more than , with melting points over . They are structurally stronger than RCC, and, thus, do not require structural reinforcement with materials such as Inconel. SHARP materials are extremely efficient at reradiating absorbed heat, thus eliminating the need for additional TPS behind and between the SHARP materials and conventional vehicle structure. NASA initially funded (and discontinued) a multi-phase R&D program through the University of Montana in 2001 to test SHARP materials on test vehicles. Actively cooled Various advanced reusable spacecraft and hypersonic aircraft designs have been proposed to employ heat shields made from temperature-resistant metal alloys that incorporate a refrigerant or cryogenic fuel circulating through them. Such a TPS concept was proposed for the X-30 National Aerospace Plane (NASP) in the mid-80s. The NASP was supposed to have been a scramjet powered hypersonic aircraft, but failed in development. In 2005 and 2012, two unmanned lifting body craft with actively cooled hulls were launched as a part of the German Sharp Edge Flight Experiment (SHEFEX). In early 2019, SpaceX was developing an actively cooled heat shield for its Starship spacecraft where a part of the thermal protection system will be a transpirationally cooled outer-skin design for the reentering spaceship. However, SpaceX abandoned this approach in favor of a modern version of heat shield tiles later in 2019. The Stoke Space Nova second stage, announced in October 2023 and not yet flying, uses a regeneratively cooled (by liquid hydrogen) heat shield. In the early 1960s various TPS systems were proposed to use water or other cooling liquid sprayed into the shock layer, or passed through channels in the heat shield. Advantages included the possibility of more all-metal designs which would be cheaper to develop, be more rugged, and eliminate the need for classified and unknown technology. The disadvantages are increased weight and complexity, and lower reliability. The concept has never been flown, but a similar technology (the plug nozzle) did undergo extensive ground testing. Propulsive entry Fuel permitting, nothing prevents a vehicle from entering the atmosphere with a retrograde engine burn, which has the double effect of slowing the vehicle down much faster than atmospheric drag alone would, and forcing the compressed hot air away from the vehicle's body. During reentry, the first stage of the SpaceX Falcon 9 performs an entry burn to rapidly decelerate from its initial hypersonic speed. ==High-drag suborbital entry==

In 2004, aircraft designer Burt Rutan demonstrated the feasibility of a shape-changing airfoil for reentry with the sub-orbital SpaceShipOne. The wings on this craft rotate upward into the feathered configuration that provides a shuttlecock effect. Thus SpaceShipOne achieves much more aerodynamic drag on reentry while not experiencing significant thermal loads. The configuration increases drag, as the craft is now less streamlined and results in more atmospheric gas particles hitting the spacecraft at higher altitudes than otherwise. The aircraft thus slows down more in higher atmospheric layers which is the key to efficient reentry. Secondly, the aircraft will automatically orient itself in this state to a high drag attitude. However, the velocity attained by SpaceShipOne prior to reentry is much lower than that of an orbital spacecraft, and engineers, including Rutan, recognize that a feathered reentry technique is not suitable for return from orbit. On 4 May 2011, the first test on the SpaceShipTwo of the feathering mechanism was made during a glideflight after release from the White Knight Two. Premature deployment of the feathering system was responsible for the 2014 VSS Enterprise crash, in which the aircraft disintegrated, killing the co-pilot. The feathered reentry was first described by Dean Chapman of NACA in 1958. In the section of his report on Composite Entry, Chapman described a solution to the problem using a high-drag device: == Inflatable heat shield entry==

Deceleration for atmospheric reentry, especially for higher-speed Mars-return missions, benefits from maximizing "the drag area of the entry system. The larger the diameter of the aeroshell, the bigger the payload can be." The subsequent missions flown on the Volna rocket failed due to launcher failure. NASA IRVE NASA launched an inflatable heat shield experimental spacecraft on 17 August 2009 with the successful first test flight of the Inflatable Re-entry Vehicle Experiment (IRVE). The heat shield had been vacuum-packed into a payload shroud and launched on a Black Brant 9 sounding rocket from NASA's Wallops Flight Facility on Wallops Island, Virginia. "Nitrogen inflated the heat shield, made of several layers of silicone-coated [Kevlar] fabric, to a mushroom shape in space several minutes after liftoff." NASA HIAD Following the success of the initial IRVE experiments, NASA developed the concept into the more ambitious Hypersonic Inflatable Aerodynamic Decelerator (HIAD). The current design is shaped like a shallow cone, with the structure built up as a stack of circular inflated tubes of gradually increasing major diameter. The forward (convex) face of the cone is covered with a flexible thermal protection system robust enough to withstand the stresses of atmospheric entry (or reentry). In 2012, a HIAD was tested as Inflatable Reentry Vehicle Experiment 3 (IRVE-3) using a sub-orbital sounding rocket, and worked. See also Low-Density Supersonic Decelerator, a NASA project with tests in 2014 and 2015 of a 6 m diameter SIAD-R. LOFTID A inflatable reentry vehicle, Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID), was launched in November 2022, inflated in orbit, reentered faster than Mach 25, and was successfully recovered on November 10. ==Entry vehicle design considerations==

There are four critical parameters considered when designing a vehicle for atmospheric entry: • Peak heat flux • Heat load • Peak deceleration • Peak dynamic pressure Peak heat flux and dynamic pressure selects the TPS material. Heat load selects the thickness of the TPS material stack. Peak deceleration is of major importance for crewed missions. The upper limit for crewed return to Earth from low Earth orbit (LEO) or lunar return is 10g. For Martian atmospheric entry after long exposure to zero gravity, the upper limit is 4g. Starting from the principle of conservative design, the engineer typically considers two worst-case trajectories, the undershoot and overshoot trajectories. The overshoot trajectory is typically defined as the shallowest-allowable entry velocity angle prior to atmospheric skip-off. The overshoot trajectory has the highest heat load and sets the TPS thickness. The undershoot trajectory is defined by the steepest allowable trajectory. For crewed missions the steepest entry angle is limited by the peak deceleration. The undershoot trajectory also has the highest peak heat flux and dynamic pressure. Consequently, the undershoot trajectory is the basis for selecting the TPS material. There is no "one size fits all" TPS material. A TPS material that is ideal for high heat flux may be too conductive (too dense) for a long duration heat load. A low-density TPS material might lack the tensile strength to resist spallation if the dynamic pressure is too high. A TPS material can perform well for a specific peak heat flux, but fail catastrophically for the same peak heat flux if the wall pressure is significantly increased (this happened with NASA's R-4 test spacecraft). Older TPS materials tend to be more labor-intensive and expensive to manufacture compared to modern materials. However, modern TPS materials often lack the flight history of the older materials (an important consideration for a risk-averse designer). Based upon Allen and Eggers discovery, maximum aeroshell bluntness (maximum drag) yields minimum TPS mass. Maximum bluntness (minimum ballistic coefficient) also yields a minimal terminal velocity at maximum altitude (very important for Mars EDL, but detrimental for military RVs). However, there is an upper limit to bluntness imposed by aerodynamic stability considerations based upon shock wave detachment. A shock wave will remain attached to the tip of a sharp cone if the cone's half-angle is below a critical value. This critical half-angle can be estimated using perfect gas theory (this specific aerodynamic instability occurs below hypersonic speeds). For a nitrogen atmosphere (Earth or Titan), the maximum allowed half-angle is approximately 60°. For a carbon dioxide atmosphere (Mars or Venus), the maximum-allowed half-angle is approximately 70°. After shock wave detachment, an entry vehicle must carry significantly more shocklayer gas around the leading edge stagnation point (the subsonic cap). Consequently, the aerodynamic center moves upstream thus causing aerodynamic instability. It is incorrect to reapply an aeroshell design intended for Titan entry (Huygens probe in a nitrogen atmosphere) for Mars entry (Beagle 2 in a carbon dioxide atmosphere). Prior to being abandoned, the Soviet Mars lander program achieved one successful landing (Mars 3), on the second of three entry attempts (the others were Mars 2 and Mars 6). The Soviet Mars landers were based upon a 60° half-angle aeroshell design. A 45° half-angle sphere-cone is typically used for atmospheric probes (surface landing not intended) even though TPS mass is not minimized. The rationale for a 45° half-angle is to have either aerodynamic stability from entry-to-impact (the heat shield is not jettisoned) or a short-and-sharp heat pulse followed by prompt heat shield jettison. A 45° sphere-cone design was used with the DS/2 Mars impactor and Pioneer Venus probes. ==Atmospheric entry accidents==

Not all atmospheric reentries have been completely successful: • Voskhod 2 – The service module failed to detach for some time, but the crew survived. • Soyuz 5 – The service module failed to detach, but the crew survived. • Apollo 15 - One of the three ringsail parachutes failed during the ocean landing, likely damaged as the spacecraft vented excess control fuel. The spacecraft was designed to land safely with only two parachutes, and the crew were uninjured. • Mars Polar Lander – Failed during EDL. The failure was believed to be the consequence of a software error. The precise cause is unknown for lack of real-time telemetry. • Space Shuttle Columbia STS-1 – a combination of launch damage, protruding gap filler, and tile installation error resulted in serious damage to the orbiter, only some of which the crew was aware. Had the crew known the extent of the damage before attempting reentry, they would have flown the shuttle to a safe altitude and then bailed out. Nevertheless, reentry was successful, and the orbiter proceeded to a normal landing. • Space Shuttle Atlantis STS-27 – Insulation from the starboard solid rocket booster nose cap struck the orbiter during launch, causing significant tile damage. This dislodged one tile completely, over an aluminum mounting plate for a TACAN antenna. The antenna sustained extreme heat damage, but prevented the hot gas from penetrating the vehicle body. • Genesis – The parachute failed to deploy due to a G-switch having been installed backwards (a similar error delayed parachute deployment for the Galileo Probe). Consequently, the Genesis entry vehicle crashed into the desert floor. The payload was damaged, but most scientific data were recoverable. • Soyuz TMA-11 – The Soyuz propulsion module failed to separate properly; fallback ballistic reentry was executed that subjected the crew to accelerations of about . The crew survived. • Starship IFT-3: The SpaceX Starship's third integrated test flight was supposed to end with a hard splashdown in the Indian Ocean. However, approximately 48.5 minutes after launch, at an altitude of 65km, contact with the spacecraft was lost, indicating that it burned up on reentry. This was caused by excessive vehicle rolling due to clogged vents on the vehicle. • Starship IFT-9- IFT 9 was going to end with a soft splashdown off the west coast of Australia but a detonation of a part in the payload area after second engine cutoff led to high pressure and excessive venting Within the nose leading to the payload deployment test and an in space burn being aborted and Starship entering at an off nominal attitude leading to a breakup during entry at approximately T+46:48 after launch. Some reentries have resulted in significant disasters: • Soyuz 1 – The attitude control system failed while still in orbit and later parachutes got entangled during the emergency landing sequence (entry, descent, and landing (EDL) failure). Lone cosmonaut Vladimir Mikhailovich Komarov died. • Soyuz 11 – During tri-module separation, a valve seal was opened by the shock, depressurizing the descent module; the crew of three asphyxiated in space minutes before reentry. • Space Shuttle Columbia STS-107 – The failure of a reinforced carbon–carbon panel on a wing leading edge caused by debris impact at launch led to breakup of the orbiter on reentry resulting in the deaths of all seven crew members. ==Uncontrolled and unprotected entries==

Of satellites that reenter, approximately 10–40% of the mass of the object may reach the surface of the Earth. On average, about one catalogued object reentered per day . Because the Earth's surface is predominantly water, most objects that survive reentry land in one of the world's oceans. The estimated chance that a given person would get hit and injured during their lifetime is around 1 in a trillion. On January 24, 1978, the Soviet Kosmos 954 () reentered and crashed near Great Slave Lake in the Northwest Territories of Canada. The satellite was nuclear-powered and left radioactive debris near its impact site. On July 11, 1979, the US Skylab space station () reentered and spread debris across the Australian Outback. The reentry was a major media event largely due to the Cosmos 954 incident, but not viewed as much as a potential disaster since it did not carry toxic nuclear or hydrazine fuel. NASA had originally hoped to use a Space Shuttle mission to either extend its life or enable a controlled reentry, but delays in the Shuttle program, plus unexpectedly high solar activity, made this impossible. On February 7, 1991, the Soviet Salyut 7 space station (), with the Kosmos 1686 module () attached, reentered and scattered debris over the town of Capitán Bermúdez, Argentina. The station had been boosted to a higher orbit in August 1986 in an attempt to keep it up until 1994, but in a scenario similar to Skylab, the planned Buran shuttle was cancelled and high solar activity caused it to come down sooner than expected. On September 7, 2011, NASA announced the impending uncontrolled reentry of the Upper Atmosphere Research Satellite () and noted that there was a small risk to the public. The decommissioned satellite reentered the atmosphere on September 24, 2011, and some pieces are presumed to have crashed into the South Pacific Ocean over a debris field long. On April 1, 2018, the Chinese Tiangong-1 space station () reentered over the Pacific Ocean, halfway between Australia and South America. The China Manned Space Engineering Office had intended to control the reentry, but lost telemetry and control in March 2017. On May 11, 2020, the core stage of Chinese Long March 5B (COSPAR ID 2020-027C) weighing roughly ) made an uncontrolled reentry over the Atlantic Ocean, near West African coast. Few pieces of rocket debris reportedly survived reentry and fell over at least two villages in Ivory Coast. On May 8, 2021, the core stage of Chinese Long March 5B (COSPAR ID 2021-0035B) weighing ) made an uncontrolled reentry, just west of the Maldives in the Indian Ocean (approximately 72.47°E longitude and 2.65°N latitude). Witnesses reported rocket debris as far away as the Arabian peninsula. Deorbit disposal Salyut 1, the world's first space station, was deliberately de-orbited into the Pacific Ocean in 1971 following the Soyuz 11 accident. Its successor, Salyut 6, was de-orbited in a controlled manner as well. On June 4, 2000, the Compton Gamma Ray Observatory was deliberately de-orbited after one of its gyroscopes failed. The debris that did not burn up fell harmlessly into the Pacific Ocean. The observatory was still operational, but the failure of another gyroscope would have made de-orbiting much more difficult and dangerous. With some controversy, NASA decided in the interest of public safety that a controlled crash was preferable to letting the craft come down at random. In 2001, the Russian Mir space station was deliberately de-orbited, and broke apart in the fashion expected by the command center during atmospheric reentry. Mir entered the Earth's atmosphere on March 23, 2001, near Nadi, Fiji, and fell into the South Pacific Ocean. On February 21, 2008, a disabled U.S. spy satellite, USA-193, was hit at an altitude of approximately with an SM-3 missile fired from the U.S. Navy cruiser off the coast of Hawaii. The satellite was inoperative, having failed to reach its intended orbit when it was launched in 2006. Due to its rapidly deteriorating orbit it was destined for uncontrolled reentry within a month. U.S. Department of Defense expressed concern that the fuel tank containing highly toxic hydrazine might survive reentry to reach the Earth's surface intact. Several governments including those of Russia, China, and Belarus protested the action as a thinly veiled demonstration of US anti-satellite capabilities. China had previously caused an international incident when it tested an anti-satellite missile in 2007. File:Closeup of Gemini 2 heatshield.jpg|Closeup of Gemini 2 heat shield File:Cross section of Gemini 2 heatshield.jpg|Cross section of Gemini 2 heat shield ==Environmental impact==

Atmospheric entry has a measurable impact on Earth's atmosphere, particularly the stratosphere. Atmospheric entry mass by spacecraft accounted for 3% compared to entries by meteoroids in 2019, but in a scenario in which large amounts of proposed satellite internet constellations are realized, artificial entries would make up 40% compared to meteoroid entries. The impact of spacecraft burning up in the atmosphere during artificial atmospheric entry is different to meteors due to the spacecraft's generally larger size and different composition. The atmospheric pollutants produced by artificial atmospheric burning-up have been traced in the atmosphere and identified as reacting and possibly negatively impacting the composition of the atmosphere and particularly the ozone layer. Considering space sustainability in regard to atmospheric impact of re-entry is by 2022 just developing and has been identified in 2024 as suffering from "atmosphere-blindness", causing global environmental injustice. This is identified as a result of the current end-of life spacecraft management, which favors the station keeping practice of controlled re-entry. This is mainly done to prevent the dangers from uncontrolled atmospheric entries and space debris. Suggested alternatives are the use of less polluting materials and by in-orbit servicing and potentially in-space recycling. ==Gallery==

CRS Orb-2 Cygnus 3 reentry.jpg|Cygnus reentering, as seen from the International Space Station Soyuz TMA-05M spacecraft reentry.jpg|Close up of reentry trail (Soyuz) Soyuz TMA-05M capsule reentry.jpg|Early reentry plasma trail (Soyuz) File:Re-entry of Progress Spacecraft 42P - NASA Earth Observatory.jpg|Progress during atmospheric entry over Earth Space Shuttle Atlantis in the sky on July 21, 2011, to its final landing.jpg|Space Shuttle reentry Space Shuttle reentry aboard flight deck.jpg|Space Shuttle cockpit view during reentry ==See also==