As mandated by PDD-63, the DoD must protect its portion of the federal government's critical infrastructure. For DoD, this is the Defense Infrastructure or DI. Protecting the Defense Infrastructure is a complex task involving ten defense sectors. It was deemed that it was nearly impossible to protect every critical asset at every location, therefore the focus was directed on protecting the critical Defense Infrastructure. The critical Defense Infrastructure is the critical assets essential to providing mission assurance.
Six phases The six phases of the DoD CIP life cycle build on one another to create a framework for a comprehensive solution for infrastructure assurance. The life cycle phases occur before, during, and after an event that may compromise or degrade the infrastructure. A synopsis of the six phases are: •
Analysis and Assessment (occurs before an event) - The Analysis and Assessment phase is the foundation and most important phase of the CIP life cycle. This phase identifies the assets absolutely critical to mission success and determines the assets’ vulnerabilities, as well as their interdependencies, configurations, and characteristics. An assessment is then made of the operational impact of infrastructure loss or degradation. In addition,
Proactive Cyber Defence may anticipate an attack against computers and networks. It applies equally well to all critical infrastructure sectors, as it involves interdicting and disrupting an attack or a threat's preparation to attack, either preemptively or in self-defense. •
Remediation (occurs before an event) - The Remediation phase involves precautionary measures and actions taken before an event occurs to fix the known cyber and physical vulnerabilities that could cause an outage or compromise a National Defense Infrastructure, or NDI, or critical asset. For example, remediation actions may include education and awareness, operational process or procedural changes or system configuration and component changes. •
Indications and Warnings (occurs before and/or during an event) - The Indications and Warnings phase involves daily sector monitoring to assess the mission assurance capabilities of critical infrastructure assets and to determine if there are event indications to report. Indications are preparatory actions that indicate whether an infrastructure event is likely to occur or is planned. Indications are based on input at the tactical, operational, theater, and strategic level. At the tactical level, input comes from asset owners. At the operational level, input comes from the NDI sectors. At the theater level, input comes from regional assets such as allied intelligence, NATO, command intelligence, allied governments, and coalition forces. At the strategic level, input comes from intelligence, law-enforcement, and the private sector. Warning is the process of notifying asset owners of a possible threat or hazard. •
Mitigation (occurs both before and during an event) - The Mitigation phase comprises actions taken before or during an event in response to warnings or incidents. DoD Critical Asset owners, NDI sectors, DoD installations, and military operators take these actions to minimize the operational impact of a critical asset's loss or debilitation. •
Incident Response (occurs after an event) - Incident Response comprises the plans and activities taken to eliminate the cause or source of an infrastructure event. •
Reconstitution (occurs after an event) - The last phase of the CIP life cycle, involves actions taken to rebuild or restore a critical asset capability after it has been damaged or destroyed. This phase is the most challenging and least developed process. Effective management of the CIP life cycle ensures that protection activities can be coordinated and reconciled among all DoD sectors. In many ways, DoD CIP, is risk management at its most imperative. Achieving success means obtaining mission assurance. Missing the mark can mean mission failure as well as human and material losses. For critical infrastructure protection, risk management requires leveraging resources to address the most critical infrastructure assets that are also the most vulnerable and that have the greatest threat exposure. The most important part of the CIP lifecycle is Phase 1. Because it is crucial to target the right assets for infrastructure protection, determining these assets is the first phase in the CIP life cycle. This phase, Analysis and Assessment, is the key and foundation of the seven lifecycle activities. Without a solid foundation, the remaining CIP life cycle phases may be flawed, resulting in a CIP plan that fails to protect the critical infrastructure and, therefore, mission assurance.
Phase 1: Analysis and Assessment Phase 1 determines what assets are important, and identifies their vulnerabilities, and dependencies so that decision makers have the information they need to make effective risk management choices. The Defense Infrastructure, or DI, is organized into ten sectors. Each sector is composed of assets, such as systems, programs, people, equipment, or facilities. Assets may be simple, such as one facility within one geographic location, or complex, involving geographically dispersed links and nodes. The Analysis and Assessment is made up of five steps that include activities that span and encompass the ten DI sectors and their assets. • I. The first step in the Analysis and Assessment phase is to identify critical assets. An asset's criticality is a function of both time and situation based on the asset's operational or business value. For the DI, value depends on several factors: First, what military operations or services rely on an asset and how those dependencies change across time Next, how sensitive the operation is to the loss or compromise of the asset, in other words what is the maximum allowable down time if the asset is compromised. Finally, what the asset's assurance profile is, in particular whether asset restoration or a switch to a backup can occur within the allowable down time. Through domain expertise and inspection, critical assets are identified and then reported to the CIP Program. • II. The second step of the Analysis and Assessment phase is Defense Infrastructure characterization. This step maps and associates critical asset functions and relationships within a DI sector. • III. The third step in the Analysis and Assessment phase is the Operational Impact Analysis. This step is accomplished through the development of operational dependency matrices and the application of operations research methods. Potential operational impacts and service-level requirements are then reflected in the asset's criticality attributes and criticality index in the CIP program. • IV. The fourth step is the Vulnerability Assessment. This step is accomplished through multiple channels. Through the CIP program, all critical assets have a baseline vulnerability index, which is calculated from inputs associated with the class of asset and geographic region such as the probability of natural disasters, criminal or national security events, and technological failures. Asset owners, host installations, the sector CIAO, or other DoD entities may provide asset operational readiness and emergency preparedness information. • V. The fifth and final step in the Analysis and Assessment phase is Interdependency Analysis. Interdependency analysis seeks to map functions and relationships among DI sectors. As a result of the Interdependency Analysis, the criticality attributes for previously identified assets may be updated and additional critical assets may be identified to the CIP program. Multiple groups within the DoD CIP structure perform analysis and assessment activities. Translating the analysis and assessment process into concrete data requires specific activities, tasks, and tools.
Phase 1 Example in the “Real World” On August 24, 2001, the Director of the Joint Staff requested USPACOM to serve as the lead support Combatant Command for creating a CIP first-ever theater CIP Plan – known as the “CIP Appendix 16 Plan”. The following is how USPACOM approached the task. USPACOM focused the Analysis and Assessment phase by organizing its activities to answer three major questions: • What is critical? • Is it vulnerable? • What can be done? To answer the question, “What is critical?”, USPACOM outlined a three-step procedure: • First, identify the project focus. • Second, complete an operational analysis. • Third, complete a Defense Infrastructure analysis. To accomplish these steps, USPACOM adopted a methodology that focuses its CIP efforts on Tier 1 assets. Tier 1 assets are assets that could cause mission failure if they are compromised or damaged. The methodology UAPACOM adopted and modified is Mission Area Analysis, or MAA. The MAA links combatant command missions to infrastructure assets that are critical to a given Operations Plan, or OPLAN, Contingency Plan, or CONPLAN, or Crisis Action Plan. Typically, the MAA process determines the assessment site priorities. USPACOM modified the process and selected the CIP assessment sites and installations prior to conducting the MAA. The following is an illustration of the USPACOM MAA process: • First, it identified the Mission Essential Requirements, or MERs, which are specific combatant commands or joint task force capabilities essential for execution of a warfighting plan. Then, they created an MER matrix for the specific command. For example, one MER may be to provide command, control, communications, and computers, or C4. • Second, it identified forces required for each MER. For example, the C4 MER is linked to a specific signal battalion. Third, it linked the forces to the necessary functions and tasks supporting the force. For example, the signal battalion is linked to the Communications and Civil Engineers functions and the task of managing the theater's C4 information systems requirements. • Third, it links assets to the functions supporting the tasks. The result is a mission area analysis of mission-critical assets. USPACOM uses the MAA data it gathers to scope and focus its efforts on truly mission-critical assets to answer the next question in its process, Is it vulnerable? The first step in answering this question is to complete an installation analysis. The next step is to complete a commercial infrastructure analysis. USPACOM relied upon two different DoD organizations for CIP assessments: Balanced Survivability Assessments, or BSAs, and Mission Assurance Assessments. The BSA is a two-week mission-focused assessment at a military installation or designated site. A Mission Assurance Assessment is unique because it uses an area assessment approach to focus on both commercial and military asset vulnerabilities and dependencies. The final step to determine vulnerabilities is to integrate the two analyses and assessments. With its critical assets and their vulnerabilities identified, USPACOM is ready to perform risk management activities to decide what can be done to protect the
mission-critical assets.
Booz Allen Hamilton developed this process at PACOM.
Phase 2: Remediation The first phase of the CIP life cycle, Analysis and Assessment, identified the critical assets of DoD sector infrastructures and the vulnerabilities or weaknesses of those critical assets. The second phase is the Remediation phase. In the Remediation phase, the known weaknesses and vulnerabilities are addressed. Remediation actions are deliberate, precautionary measures designed to fix known virtual and physical vulnerabilities before an event occurs. The purpose of remediation is to improve the reliability, availability, and survivability of critical assets and infrastructures. Remediation actions apply to any type of vulnerability, regardless of its cause. They apply to acts of nature, technology failures, or deliberate malicious actions. The cost of each remediation action depends on the nature of the vulnerability it addresses. The Defense Infrastructure Sector Assurance Plan that each infrastructure sector must develop, establishes the priorities and resources for remediation. Remediation requirements are determined by multiple factors. These are analysis and assessment, input from military planners and other DoD sectors, the National Infrastructure Assurance Plan and other plans, reports, and information on national infrastructure vulnerabilities and remediation, as well as intelligence estimates and assessments of threats. Remediation requirements are also gathered through lessons learned from Defense Infrastructure sector monitoring and reporting and infrastructure protection operations and exercises. The CIP program tracks the status of remediation activities for critical assets. Remediation activities to protect the critical Defense Infrastructure cross multiple Department components.
Phase 3: Indications and Warnings The need to monitor activities and warn of potential threats to the United States is not new. From conventional assaults to potential nuclear attacks, the military has been at the forefront of monitoring and warning of potential dangers since the founding of the country. Protecting the security and well-being of the United States, including the critical Defense Infrastructure, has now entered a new era. It has been deemed essential to have a coordinated ability to identify and warn of potential or actual incidents among critical infrastructure domains. The ability to detect and warn of infrastructure events is the third phase of the critical infrastructure protection life cycle, the Indications and Warnings phase. Indications and warnings are actions or infrastructure conditions that signal an event is either: • Likely, • Planned or • Underway. Historically, DoD event indications have focused and relied on intelligence information about foreign developments. These event indications have been expanded to include all potential infrastructure disruption or degradation, regardless of its cause. DoD CIP indications are based on four levels of input: • Tactical level input from DoD asset owners or installations • Operational-level input from sector Chief Information Assurance Officers (CIAOs) • Theater-level input from command and service intelligence and counter-intelligence activities. • Strategic-level intelligence from the intelligence community, law enforcement, and the private sector This fusion of traditional intelligence information with sector-specific information has been determined to be essential for meaningful CIP indications. If an indication is detected, a warning notifying the appropriate asset owners of a possible or occurring event or hazard can be issued. The sector's assurance plan determines what conditions and actions are monitored and reported for each Defense Infrastructure Sector. Each sector must develop a written Defense Sector Assurance Plan that includes a compendium of sector incidents for monitoring and reporting. The sector incident compendium is made up of three types of incidents: • Nationally defined reportable incidents • DoD defined reportable incidents, and • Sector-defined reportable incidents. DoD critical asset owners, installations, and sector CIAOs determine the DoD and sector-defined incidents. Each of the reportable incidents or classes of incidents must include the following components: • Who should monitor the incident • How soon the incident must be reported • Which information elements the incident should contain • How the incident reporting should be routed • What follow-up actions are required The
National Infrastructure Protection Center (NIPC) is the primary national warning center for significant infrastructure attacks. Critical asset owners, DoD installations, and Sector CIAOs monitor the infrastructure daily. Indications of an infrastructure incident are reported to the
National Military Command Center, or NMCC. If indications are on a computer network, they are also reported to the Joint Task Force Computer Network Operations (JTF-CNO). The NMCC and JTF-CNO assess the indications and pass them to the NIPC and appropriate DoD organizations. When the NIPC determines that an infrastructure event is likely to occur, is planned, or is under way, it issues a national warning. For DoD, the NIPC passes its warnings and alerts to the NMCC and JTF-CNO. These warnings and alerts are then passed to the DoD components. The warning may include guidance regarding additional protection measures DoD should take.
Phase 4: Mitigation Phase 1 of the CIP life cycle provided a layer of protection by identifying and assessing critical assets and their vulnerabilities. Phase 2 provided another layer of protection by remediating or improving the identified deficiencies and weaknesses of an asset. Even with these protections and precautions, an infrastructure incident was still possible. When it does the Indications and Warnings phase goes into effect. The Mitigation phase (Phase 4), is made up of preplanned coordinated actions in response to infrastructure warnings or incidents. Mitigation actions are taken before or during an infrastructure event. These actions are designed to minimize the operational impact of the loss of a critical asset, facilitate incident response, and quickly restore the infrastructure service. A primary purpose of the Mitigation phase is to minimize the operational impact on other critical Defense Infrastructures and assets when a critical asset is lost or damaged. As an example, if there is a U.S. installation, Site A, located in a host nation. Site A is a tier 1 asset, meaning that if it fails, the Combatant Commands mission fails. Site A has mutual Global Information Grid Command Control (GIG/C2), information interdependencies with Sites B and C. In addition, other Defense Infrastructure sectors rely on Site A for mission capabilities. In this scenario, what could be the impact if the supply line to the commercial power plant that provides the installation's primary power is accidentally severed. Because of all the interdependencies, losing this asset is more than the loss of just one site. It means the loss of other sector capabilities. A possible mitigation action might be for Site A to go on backup power. An alternate action could be to pass complete control of Site A's functionality to another site, where redundancy has been previously arranged. These actions would limit the impact of this incident on the other sites and related sectors. In addition to lessening the operational impact of a critical infrastructure event, the Mitigation phase of the CIP life cycle supports and complements two other life cycle phases. Mitigation actions aid in the emergency, investigation, and management activities of Phase 5, Incident Response. They also facilitate the reconstitution activities of Phase 6. During the Mitigation phase, DoD critical asset owners, DoD installations, and Sector Chief Infrastructure Assurance Officers, or CIAOs, work with the National Military Command Center (NMCC) and the Joint Task Force-Computer Network Operations (JTF-CNO) to develop, train for, and exercise mitigation responses for various scenarios. When there is a warning, emergency, or infrastructure incident, the critical asset owners, installations, and Sector CIAOs initiate mitigation actions to sustain service to the DoD. They also provide mitigation status information to the NMCC and JTF-CNO. The NMCC monitors for consequences from an event within one Defense Infrastructure sector that are significant enough to affect other sectors. For events that cross two or more sectors, the NMCC advises on the prioritization and coordination of mitigation actions. When event threats or consequences continue to escalate, the NMCC directs mitigation actions by sector to ensure a coordinated response across the DoD. The NMCC and the JTF-CNO keep the National Infrastructure Protection Center, or NIPC, apprised of any significant mitigation activities.
Phase 5: Incident response When an event affects the Defense Infrastructure, the Incident Response phase begins. Incident Response is the fifth phase of the CIP life cycle. The purpose of the Incident Response phase is to eliminate the cause or source of an infrastructure event. For example, during the
9/11 attacks on the
World Trade Center and
Pentagon, all non-military airplanes were grounded over the United States to prevent further incidents. Response activities included emergency measures, not from the asset owners or operators, but from dedicated third parties such as law enforcement, medical rescue, fire rescue, hazardous material or explosives handling, and investigative agencies. Response to Defense Infrastructure incidents can take one of two paths depending on whether or not the event affects a DoD computer network. When incidents compromise a DoD computer network, the Joint Task Force-Computer Network Operations (JTF-CNO) directs the response activities. These activities are designed to stop the computer network attack, contain and mitigate damage to a DoD information network and then restore minimum required functionality. JTF-CNO also requests and coordinates any support or assistance from other Federal agencies and civilian organizations during incidents affecting a DoD network. When incidents impact any other DoD owned assets, installation commanders and critical asset owners follow traditional channels and procedures to coordinate responses. This includes notifying affected Sector Chief Infrastructure Assurance Officers, or CIAOs, in the initial notice and status reporting. Although third parties play a major role in the response to Defense Infrastructure events, DoD CIP personnel also have responsibilities to fulfill.
Phase 6: Reconstitution After the source or cause of an infrastructure event is eliminated or contained, the infrastructure and its capabilities must be restored. Reconstitution is the last phase of the critical infrastructure protection. Reconstitution is probably the most challenging and least developed process of the life cycle. DoD critical asset owners have the major responsibility for reconstitution. ==See also==