Gender Every matched pair of threads,
external and
internal, can be described as
male and
female. Generally speaking, the threads on an external surface are considered male, while the ones on an internal surface are considered female. For example, a
screw has male threads, while its matching hole (whether in nut or substrate) has female threads. This property is called
gender. Assembling a male-threaded fastener to a female-threaded one is called
mating.
Handedness The helix of a thread can twist in two possible directions, which is known as
handedness. Most threads are oriented so that the threaded item, when seen from a point of view on the axis through the center of the helix, moves away from the viewer when it is turned in a
clockwise direction, and moves towards the viewer when it is turned counterclockwise. This is known as a
right-handed (
RH) thread, because it follows the
right-hand grip rule. Threads oriented in the opposite direction are known as
left-handed (
LH). By common convention, right-handedness is the default handedness for screw threads. Therefore, most threaded parts and fasteners have right-handed threads. Left-handed thread applications include: • Where the rotation of a shaft would cause a conventional right-handed nut to loosen rather than to tighten due to applied torque or to
fretting induced precession. Examples include: • The
left foot pedal on a
bicycle • In some gas supply connections to prevent dangerous misconnections, for example: • In gas welding the flammable gas supply uses left-handed threads, while the oxygen supply if there is one has a conventional thread • The
POL valve for
LPG cylinders • In a situation where neither threaded pipe end can be rotated to tighten or loosen the joint (e.g. in traditional heating pipes running through several rooms in a building). In such a case, the
coupling will have one right-handed and one left-handed thread. • In some instances, for example early
ballpoint pens, to provide a "secret" method of disassembly • In artillery projectiles, anything that screws into the projectile must be given consideration as to what will happen when the projectile is fired, e.g., anything that screws into the base from the bottom of the projectile must be left hand threaded • In mechanisms to give a more intuitive action as: • The leadscrew of the cross slide of a
lathe to cause the cross slide to move away from the operator when the leadscrew is turned clockwise • The depth of cut screw of a "Bailey" (or "Stanley-Bailey") type metal
plane (tool) for the blade to move in the direction of a regulating right hand finger • Some
Edison base lamps and fittings (such as those formerly used on the
New York City Subway or the pre-
World War I Sprague-Thomson rolling stock of the
Paris Metro) have a left-hand thread to deter theft, because they cannot be used in other light fixtures
Form The cross-sectional shape of a thread is often called its
form or
threadform (also spelled
thread form). It may be
square,
triangular,
trapezoidal, or other shapes. The terms
form and
threadform sometimes refer to all design aspects taken together (cross-sectional shape, pitch, and diameters), but commonly refer to the standardized geometry used by the screw. Major categories of threads include machine threads, material threads, and power threads. Most triangular threadforms are based on an
isosceles triangle. These are usually called
V-threads or
vee-threads because of the shape of the
letter V. For 60° V-threads, the isosceles triangle is, more specifically,
equilateral. For
buttress threads, the triangle is
scalene. The theoretical triangle is usually
truncated to varying degrees (that is, the tip of the triangle is cut short). A V-thread in which there is no truncation (or a minuscule amount considered negligible) is called a
sharp V-thread. Truncation occurs (and is codified in standards) for practical reasons—the thread-cutting or thread-forming tool cannot practically have a perfectly sharp point, and truncation is desirable anyway, because otherwise: • The cutting or forming tool's edge will break too easily; • The part or fastener's thread crests will have
burrs upon cutting, and will be too susceptible to additional future burring resulting from dents (nicks); • The roots and crests of mating male and female threads need clearance to ensure that the sloped sides of the V meet properly despite error in pitch diameter and dirt and nick-induced burrs. • The point of the threadform adds little strength to the thread. In
ball screws, the male-female pairs have bearing balls in between.
Roller screws use conventional thread forms and threaded rollers instead of balls.
Angle The included angle characteristic of the cross-sectional shape is often called the
thread angle. For most V-threads, this is standardized as 60
degrees, but any angle can be used. The cross section to measure this angle lies on a plane which includes the axis of the cylinder or cone on which the thread is produced.
Lead, pitch, and starts Lead () and
pitch are closely related concepts. They can be confused because they are the same for most screws.
Lead is the distance along the screw's axis that is covered by one complete rotation of the screw thread (360°).
Pitch is the distance from the crest of one thread to the next one at the same point. Because the vast majority of screw threadforms are
single-start threadforms, their lead and pitch are the same. Single-start means that there is only one "ridge" wrapped around the cylinder of the screw's body. Each time that the screw's body rotates one turn (360°), it has advanced axially by the width of one ridge. "Double-start" means that there are two "ridges" wrapped around the cylinder of the screw's body. Each time that the screw's body rotates one turn (360°), it has advanced axially by the width of two ridges. Another way to express this is that lead and pitch are parametrically related, and the
parameter that relates them, the number of starts, very often has a value of 1, in which case their relationship becomes equality. In general, lead is equal to pitch times the number of starts. Whereas metric threads are usually defined by their pitch, that is, how much distance per thread, inch-based standards usually use the reverse logic, that is, how many threads occur per a given distance. Thus, inch-based threads are defined in terms of
threads per inch (TPI). Pitch and TPI describe the same underlying physical property—merely in different terms. When the inch is used as the unit of measurement for pitch, TPI is the reciprocal of pitch and vice versa. For example, a -20 thread has 20 TPI, which means that its pitch is inch (). As the distance from the crest of one thread to the next, pitch can be compared to the
wavelength of a
wave. Another wave analogy is that pitch and TPI are inverses of each other in a similar way that
period and frequency are inverses of each other.
Coarse versus fine Coarse threads are those with larger pitch (fewer threads per axial distance), and fine threads are those with smaller pitch (more threads per axial distance). Coarse threads have a larger threadform relative to screw diameter, where fine threads have a smaller threadform relative to screw diameter. This distinction is analogous to that between coarse teeth and fine teeth on a
saw or
file, or between coarse grit and fine grit on
sandpaper. ) The common V-thread standards (
ISO 261 and
Unified Thread Standard) include a coarse pitch and a fine pitch for each major diameter. For example, -13 belongs to the UNC series (Unified National Coarse) and -20 belongs to the UNF series (Unified National Fine). Similarly, M10 (10 mm nominal outer diameter) as per ISO 261 has a coarse thread version at 1.5 mm pitch and a fine thread version at 1.25 mm pitch. The terms
coarse and
fine pertain only to thread pitch, not quality or tolerances. Coarse threads are more resistant to stripping and cross threading because they have greater flank engagement. Coarse threads install much faster as they require fewer turns per unit length. Finer threads are stronger as they have a larger stress area for the same diameter thread. Fine threads are less likely to vibrate loose as they have a smaller helix angle and allow finer adjustment. Finer threads develop greater preload with less tightening torque.
Diameters in a technical drawing There are three characteristic diameters (
⌀) of threads:
major diameter,
minor diameter, and
pitch diameter: Industry standards specify minimum (min.) and maximum (max.) limits for each of these, for all recognized thread sizes. The minimum limits for
external (or
bolt, in ISO terminology), and the maximum limits for
internal (
nut), thread sizes are there to ensure that threads do not strip at the tensile strength limits for the parent material. The minimum limits for internal, and maximum limits for external, threads are there to ensure that the threads fit together.
Major diameter The major diameter of threads is the larger of two extreme diameters delimiting the height of the thread profile, as a cross-sectional view is taken in a plane containing the axis of the threads. For a screw, this is its outside diameter (OD). The major diameter of a nut cannot be directly measured (as it is obstructed by the threads themselves) but it may be tested with go/no-go gauges. The major diameter of external threads is normally smaller than the major diameter of the internal threads, if the threads are designed to fit together. But this requirement alone does not guarantee that a bolt and a nut of the same pitch would fit together: the same requirement must separately be made for the minor and pitch diameters of the threads. Besides providing for a clearance between the
crest of the bolt threads and the
root of the nut threads, one must also ensure that the clearances are not so excessive as to cause the fasteners to fail.
Minor diameter s is the same as that of all
ISO metric screw threads. Only the commonly used values for
Dmaj and
P differ between the two standards. The minor diameter is the lower extreme diameter of the thread. Major diameter minus minor diameter, divided by two, equals the height of the thread. The minor diameter of a nut is its inside diameter. The minor diameter of a bolt can be measured with go/no-go gauges or, directly, with an
optical comparator. As shown in the figure at right, threads of equal pitch and angle that have matching minor diameters, with differing major and pitch diameters, may appear to fit snugly, but only do so radially; threads that have only major diameters matching (not shown) could also be visualized as not allowing radial movement. The reduced
material condition, due to the unused spaces between the threads, must be minimized so as not to overly weaken the fasteners. In order to fit a male thread into the corresponding female thread, the female major and minor diameters must be slightly larger than the male major and minor diameters. However this excess does not usually appear in tables of sizes. Calipers measure the female minor diameter (inside diameter, ID), which is less than caliper measurement of the male major diameter (outside diameter, OD). For example, tables of caliper measurements show 0.69 female ID and 0.75 male OD for the standards of "3/4 SAE J512" threads and "3/4-14 UNF JIS SAE-J514 ISO 8434-2". Note the female threads are identified by the corresponding male major diameter (3/4 inch), not by the actual measurement of the female threads.
Pitch diameter The pitch diameter (PD, or
D2) of a particular thread, internal or external, is the diameter of a cylindrical surface, axially concentric to the thread, which intersects the thread flanks at equidistant points. When viewed in a cross-sectional plane containing the axis of the thread, the distance between these points being exactly one half the pitch distance. Equivalently, a line running parallel to the axis and a distance
D2 away from it, the "PD line," slices the
sharp-V form of the thread, having flanks coincident with the flanks of the thread under test, at exactly 50% of its height. We have assumed that the flanks have the proper shape, angle, and pitch for the specified thread standard. It is generally unrelated to the major (
D) and minor (
D1) diameters, especially if the crest and root truncations of the sharp-V form at these diameters are unknown. Everything else being ideal,
D2,
D, &
D1, together, would fully describe the thread form. Knowledge of PD determines the position of the sharp-V thread form, the sides of which coincide with the straight sides of the thread flanks: e.g., the crest of the external thread would truncate these sides a radial displacement
D −
D2 away from the position of the PD line. Provided that there are moderate non-negative clearances between the root and crest of the opposing threads, and everything else is ideal, if the pitch diameters of a screw and nut are exactly matched, there should be no play at all between the two as assembled, even in the presence of positive root-crest clearances. This is the case when the flanks of the threads come into intimate contact with one another, before the roots and crests do, if at all. However, this ideal condition would in practice only be approximated and would generally require wrench-assisted assembly, possibly causing the
galling of the threads. For this reason, some
allowance, or minimum difference, between the PDs of the internal and external threads has to generally be provided for, to eliminate the possibility of deviations from the ideal thread form causing
interference and to expedite hand assembly up to the length of engagement. Such allowances, or
fundamental deviations, as ISO standards call them, are provided for in various degrees in corresponding
classes of fit for ranges of thread sizes. At one extreme, no allowance is provided by a class, but the maximum PD of the external thread is specified to be the same as the minimum PD of the internal thread, within specified tolerances, ensuring that the two can be assembled, with some looseness of fit still possible due to the margin of tolerance. A class called
interference fit may even provide for negative allowances, where the PD of the screw is greater than the PD of the nut by at least the amount of the allowance. The pitch diameter of external threads is measured by various methods: • A dedicated type of
micrometer, called a thread mic or pitch mic, which has a V-anvil and a conical spindle tip, contacts the thread flanks for a direct reading. • A general-purpose micrometer (flat anvil and spindle) is used over a set of three wires that rest on the thread flanks, and a known constant is subtracted from the reading. (The wires are truly gauge pins, being ground to precise size, although "wires" is their common name.) This method is called the 3-wire method. Sometimes grease is used to hold the wires in place, helping the user to juggle the part, mic, and wires into position. • An
optical comparator may also be used to determine PD graphically.
Classes of fit The way in which male and female fit together, including
play and friction, is classified (categorized) in thread standards. Achieving a certain
class of fit requires the ability to work within tolerance ranges for dimension (size) and
surface finish. Defining and achieving classes of fit are important for
interchangeability. Classes include 1, 2, 3 (loose to tight); A (external) and B (internal); and various systems such as H and D limits.
Tolerance classes Thread limit Thread limit or
pitch diameter limit is a standard used for classifying the tolerance of the thread pitch diameter for
taps. For imperial, H or L limits are used which designate how many units of 0.0005 inch over or undersized the pitch diameter is from its basic value, respectively. Thus a tap designated with an H limit of 3, denoted
H3, would have a pitch diameter 0.0005 × 3 = 0.0015 inch larger than base pitch diameter and would thus result in cutting an internal thread with a looser fit than say an H2 tap. Metric uses D or DU limits which is the same system as imperial, but uses D or DU designators for over and undersized respectively, and goes by units of . Generally taps come in the range of H1 to H5 and rarely L1. The pitch diameter of a thread is measured where the radial cross section of a single thread equals half the pitch, for example: 16 pitch thread = in = 0.0625in the pitch actual pitch diameter of the thread is measured at the radial cross section measures 0.03125in.
Interchangeability To achieve a predictably successful mating of male and female threads and assured interchangeability between males and between females, standards for form, size, and finish must exist and be followed.
Standardization of threads is discussed below.
Thread depth Screw threads are almost never made perfectly sharp (no truncation at the crest or root), but instead are truncated, yielding a final
thread depth that can be expressed as a fraction of the pitch value. The UTS and ISO standards codify the amount of truncation, including tolerance ranges. A perfectly sharp 60° V-thread will have a depth of thread ("height" from root to crest) equal to 0.866 of the pitch. This fact is intrinsic to the geometry of an equilateral triangle — a direct result of the basic
trigonometric functions. It is independent of measurement units (inch vs mm). However, UTS and ISO threads are not sharp threads. The major and minor diameters delimit truncations on either side of the sharp V. The nominal diameter of Metric (e.g. M8) and Unified (e.g. in) threads is the theoretical major diameter of the male thread, which is truncated (diametrically) by of the pitch from the dimension over the tips of the "fundamental" (sharp cornered) triangles. The resulting flats on the crests of the male thread are theoretically one eighth of the pitch wide (expressed with the notation
p or 0.125
p), although the actual geometry definition has more variables than that. A full (100%) UTS or ISO thread has a height of around 0.65
p. Threads can be (and often are) truncated a bit more, yielding thread depths of 60% to 75% of the 0.65
p value. For example, a 75% thread sacrifices only a small amount of strength in exchange for a significant reduction in the force required to cut the thread. The result is that
tap and die wear is reduced, the likelihood of breakage is lessened and higher cutting speeds can often be employed. This additional truncation is achieved by using a slightly larger
tap drill in the case of female threads, or by slightly reducing the diameter of the threaded area of workpiece in the case of male threads, the latter effectively reducing the thread's
major diameter. In the case of female threads, tap drill charts typically specify sizes that will produce an approximate 75% thread. A 60% thread may be appropriate in cases where high tensile loading will not be expected. In both cases, the
pitch diameter is not affected. The balancing of truncation versus thread strength is similar to many engineering decisions involving the strength, weight and cost of material, as well as the cost to machine it.
Taper Tapered threads are used on fasteners and pipe. A common example of a fastener with a tapered thread is a
wood screw. The
threaded pipes used in some plumbing installations for the delivery of fluids under pressure have a threaded section that is
slightly conical. Examples are the
NPT and
BSP series. The seal provided by a threaded pipe joint is created when a tapered externally threaded end is tightened into an end with internal threads. For most pipe joints, a good seal requires the application of a separate sealant into the joint, such as
thread seal tape, or a liquid or paste pipe sealant such as
pipe dope. == History ==