Airbag

Airbags are considered "passive" restraints and act as a supplement to "active" restraints. Because no action by a vehicle occupant is required to activate or use the airbag, it is considered a "passive" device. This is in contrast to seat belts, which are considered "active" devices because the vehicle occupant must act to enable them. This terminology is not related to active and passive safety, which are, respectively, systems designed to prevent collisions in the first place, and systems designed to minimize the effects of collisions once they occur. In this use, a car Anti-lock braking system qualifies as an active-safety device, while both its seat belts and airbags qualify as passive-safety devices. Terminological confusion can arise from the fact that passive devices and systems—those requiring no input or action by the vehicle occupant—can operate independently in an active manner; an airbag is one such device. Vehicle safety professionals are generally careful in their use of language to avoid this sort of confusion. However, advertising principles sometimes prevent such semantic caution in the consumer marketing of safety features. Further confusing the terminology, the aviation safety community uses the terms "active" and "passive" in the opposite sense from the automotive industry. == History ==

commemorating Round and Parrott's patent, at Birmingham Dental Hospital with ACRS Origins The airbag "for the covering of aeroplane and other vehicle parts" traces its origins to a United States patent, submitted in 1919 by two dentists from Birmingham, Arthur Parrott and Harold Round. The patent was approved in 1920. Air-filled bladders were in use as early as 1951. The airbag specifically for automobile use is credited independently to the American John W. Hetrick, who filed for an airbag patent on 5 August 1952, that was granted #2,649,311 by the United States Patent Office on 18 August 1953. German patent #896,312 filed for by engineer Walter Linderer on 6 October 1951 was issued on 12 November 1953, approximately three months after American John Hetrick. The airbags proposed by Hetrick and Linderer were based on compressed air released by a spring, bumper contact, or by the driver. Later research during the 1960s showed that compressed air could not inflate the mechanical airbags fast enough to ensure maximum safety, leading to the current chemical and electrical airbags. In patent applications, manufacturers sometimes use the term "inflatable occupant restraint systems". Hetrick was an industrial engineer and member of the United States Navy. His airbag design, however, only came about when he combined his experiences working with navy torpedoes with his desire to protect his family on the road. Despite working with the major automobile manufacturers of his time, Hetrick was unable to attract investment. Although airbags are now required in every automobile sold in the United States, Hetrick's 1951 patent filing serves as an example of a "valuable" invention with little economic value to its inventor. Its first commercial use was not implemented until after the patent expired in 1971, at which point the airbag was installed in a few experimental Ford cars. In 1964, a Japanese automobile engineer, Yasuzaburou Kobori (小堀保三郎), started developing an airbag "safety net" system. His design harnessed an explosive to inflate an airbag, for which he was later awarded patents in 14 countries. He died in 1975, before seeing the widespread adoption of airbag systems. In 1967, a breakthrough in developing airbag crash sensors came when Allen K. Breed invented a ball-in-tube mechanism for crash detection. Under his system, an electromechanical sensor with a steel ball attached to a tube by a magnet would inflate an airbag in under 30 milliseconds. A small explosion of sodium azide was used instead of compressed air during inflation for the first time. while the Italian Eaton-Livia company offered a variant with localized air cushions. In the early 1970s, General Motors began offering cars equipped with airbags, initially in government fleet-purchased 1973 Chevrolet Impala sedans. These cars came with a 1974-style Oldsmobile instrument panel and a unique steering wheel that contained the driver-side airbag. Two of these cars were crash tested after 20 years and the airbags deployed perfectly. An early example of the airbag cars survives as of 2009. GM's Oldsmobile Toronado was the first domestic U.S. vehicle to include a passenger airbag in 1973. General Motors marketed its first airbag modules under the "Air Cushion Restraint System" name, or ACRS. The automaker discontinued the option for its 1977 model year, citing a lack of consumer interest. Ford and GM then spent years lobbying against air-bag requirements, claiming that the devices were unfeasible and inappropriate. Chrysler made driver-side airbags standard on 1988 and 1989 models, but airbags did not become widespread in American cars until the early 1990s. As a substitute for seat belts Airbags for passenger cars were introduced in the United States in the 1970s. When seat-belt usage rates in the country were quite low compared to modern-day, Ford built experimental cars with airbags in 1971. Allstate operated a fleet of 200 Mercury Montereys and showed the reliability of airbags as well as their operation in crash testing, which also was promoted by the insurance company in popular magazine advertisements. General Motors followed in 1973 using full-sized Chevrolet vehicles. The early fleet of experimental GM vehicles equipped with airbags experienced seven fatalities, one of which was later suspected to have been caused by the airbag. In 1974, GM made its ACRS system (which consisted of a padded lower dashboard and a passenger-side air bag) available as a regular production option (RPO code AR3) in full-sized Cadillac, Buick and Oldsmobile models. The GM cars from the 1970s equipped with ACRS had a driver-side airbag, and a driver-side knee restraint. The passenger-side airbag protected both front passengers, The Porsche 944 and 944S had this as an available option. The same year also had the first airbag in a Japanese car, the Honda Legend. In 1988, Chrysler became the first United States automaker to fit a driver-side airbag as standard equipment, which was offered in six different models. The following year, Chrysler became the first US auto manufacturer to offer driver-side airbags in all its new passenger models. Chrysler also began featuring the airbags in advertisements showing how the devices had saved lives that helped the public know the value of them and safety became a selling advantage in the late 1980s. All versions of the Chrysler minivans came with airbags starting for the 1991 model year. The 1993 Jeep Grand Cherokee became the first SUV to offer a driver-side airbag when it was launched in 1992. Driver and passenger airbags became standard equipment in all Dodge Intrepid, Eagle Vision, and Chrysler Concorde sedans ahead of any safety regulations. Early 1993 saw the 4-millionth airbag-equipped Chrysler vehicle roll off the assembly line. In October 1993, the Dodge Ram became the first pickup truck with a standard driver-side airbag. The first known collision between two airbag-equipped automobiles took place on 12 March 1990 in Virginia, USA. A 1989 Chrysler LeBaron crossed the center line and hit another 1989 Chrysler LeBaron in a head-on collision, causing both driver airbags to deploy. The drivers suffered only minor injuries despite extensive damage to the vehicles. The United States Intermodal Surface Transportation Efficiency Act of 1991 required passenger cars and light trucks built after 1 September 1998 to have airbags for the driver and the front passenger. In the United States, NHTSA estimated that airbags had saved over 4,600 lives by 1 September 1999; however, the crash deployment experience of the early 1990s installations indicated that some fatalities and serious injuries were in fact caused by airbags. Shape of airbags The Citroën C4 provided the first "shaped" driver airbag, made possible by this car's unusual fixed-hub steering wheel. In 2019, Honda announced it would introduce a new front passenger airbag technology. Developed by Autoliv and Honda R&D in Ohio, United States, this new airbag design features three inflatable chambers connected across the front by a "noninflatable sail panel." The two outer chambers are larger than the middle chamber. When the airbag deploys, the sail panel cushions the occupant's head from the impact of hitting the airbag, and the three chambers hold the occupant's head in place, like a catcher's mitt. The goal of the tri-chamber airbag is to help "arrest high-speed movement" of the head, thereby reducing the likelihood of concussion injuries in a collision. The first vehicle to come with the tri-chamber airbag installed from the factory was in 2020 (for the 2021 model year) for the Acura TLX. Honda hopes that the new technology will soon make its way to all vehicles. Rear airbag Mercedes began offering rear passengers protection in frontal collisions in September 2020 (for the 2021 model year) for the Mercedes-Benz S-Class (W223). The W223 S-Class is the first car equipped with rear seat airbags that use gas to inflate supporting structures that unfold and extend a bag that fills with ambient air, instead of conventional fully gas-inflated airbags that are widely used in automotive airbag systems. Side airbag inflated permanently for display purposes Essentially, two types of side airbags are commonly used today - the side-torso airbag and the side-curtain airbag. More recently, center airbags are becoming more common in the European market. Most vehicles equipped with side-curtain airbags also include side-torso airbags. However, some, such as the Chevrolet Cobalt, 2007–09 model Chevrolet Silverado/GMC Sierra, and 2009–12 Dodge Ram do not feature the side-torso airbag. From around 2000, side-impact airbags became commonplace on even low- to mid-range vehicles, such as the smaller-engined versions of the Ford Fiesta and Peugeot 206, and curtain airbags were also becoming regular features on mass-market cars. The Toyota Avensis, launched in 2003, was the first mass-market car to be sold in Europe with nine airbags. Side torso airbag Side-impact airbags or side-torso airbags are a category of airbags usually located in the seat or door panel, and inflate between the seat occupant and the door. These airbags are designed to reduce the risk of injury to the pelvic and lower abdomen regions. Most vehicles are now being equipped with different types of designs, to help reduce injury and ejection from the vehicle in rollover crashes. More recent side-airbag designs include a two-chamber system; a firmer lower chamber for the pelvic region and softer upper chamber for the ribcage. Swedish company Autoliv AB was granted a patent on side-impact airbags, and they were first offered as an option in 1994 on the 1995 Volvo 850, and as standard equipment on all Volvo cars made after 1995. the "Head Protection System (HPS)" as standard equipment. This airbag was designed to offer head protection in side impact collisions and also maintained inflation for up to seven seconds for rollover protection. However, this tubular-shaped airbag design has been quickly replaced by an inflatable 'curtain' airbag. In May 1998, Toyota began offering a side-curtain airbag deploying from the roof on the Progrés. In 1998, the Volvo S80 was given roof-mounted curtain airbags to protect both front and rear passengers. Curtain airbags were then made standard equipment on all new Volvo cars from 2000 except for the first-generation C70, which received an enlarged side-torso airbag that also protects the head of front-seat occupants. Many recent SUVs and MPVs have a long inflatable curtain airbag that protects all rows of seats. In many vehicles, the curtain airbags are programmed to deploy during some/all frontal impacts to manage passenger kinetics (e.g. head hitting B-pillar on the rebound), especially in offset crashes such as the IIHS's small overlap crash test. Roll-sensing curtain airbag (RSCA) Roll-sensing curtain airbags are designed to stay inflated for a longer duration of time, cover a larger proportion of the window, and be deployed in a roll-over crash. They offer protection to occupants' heads and help to prevent ejection. SUVs and pickups are more likely to be equipped with RSCAs due to their higher probability of rolling over and often a switch can disable the feature in case the driver wants to take the vehicle off-road. Center airbag deployed in a static out-of-position test: The purpose of the test was to find out how this airbag affects a 3-year-old child who is out of his seat and in the direct reach of the airbag. seat belt airbag In 2009, Toyota developed the first production rear-seat center airbag designed to reduce the severity of secondary injuries to rear passengers in a side collision. This system deploys from the rear center seat first appearing in on the Crown Majesta. In late 2012, General Motors with supplier Takata introduced a front center airbag; it deploys from the driver's seat. Hyundai Motor Group announced its development of a center-side airbag on September 18, 2019, installed inside the driver's seat. Some Volkswagen vehicles in 2022 equipped with center airbags include the ID.3 and the Golf. The Polestar 2 also includes a center airbag. Škoda makes center airbags standard equipment in cars and Honda wants to add center airbags to their advanced airbag system in 2023. With EuroNCAP updating its testing guidelines in 2020, European and Australian market vehicles increasingly use front-center airbags, rear torso airbags, and rear seat belt pre-tensioners. Knee airbag The second driver-side and separate knee airbag was used in the Kia Sportage SUV and has been standard equipment since then. The airbag is located beneath the steering wheel. after a frontal collision test, the driver-side knee airbag was also deployed. Blue and yellow markings indicate the dummy's knees. The Toyota Caldina introduced the first driver-side SRS knee airbag on the Japanese market in 2002. Toyota Avensis became the first vehicle sold in Europe equipped with a driver's knee airbag. The EuroNCAP reported on the 2003 Avensis, "There has been much effort to protect the driver's knees and legs and a knee airbag worked well." Since then certain models have also included front-passenger knee airbags, which deploy near or over the glove compartment in a crash. Knee airbags are designed to reduce leg injury. The knee airbag has become increasingly common since 2000. Rear curtain airbag In 2008, the new Toyota iQ microcar featured the first production rear-curtain shield airbag to protect the rear occupants' heads in the event of a rear-end impact. Seat cushion airbag Another feature of the Toyota iQ was a seat-cushion airbag in the passenger seat to prevent the pelvis from diving below the lap belt during a frontal impact or submarining. Later Toyota models such as the Yaris added the feature to the driver's seat, as well. Seat-belt airbag The seat-belt airbag is designed to better distribute the forces experienced by a buckled person in a crash using an increased seat belt area. This is done to reduce possible injuries to the rib cage or chest of the belt wearer. • 2010: Ford Explorer and 2013 Ford Flex: optional rear seat belt airbags; standard on the 2013 Lincoln MKT • 2010: Lexus LFA had seat belt airbags for driver and passenger • 2013: Mercedes-Benz S-Class (W222) has rear seat belt bags • 2014: Ford Mondeo Mk IV has optional rear seat belt airbags for the two outer seats Cessna Aircraft also introduced seat belt airbags. standard on the 172, 182, and 206. Pedestrian airbag Airbag(s) mounted to the exterior of vehicles, so-called "pedestrian airbags", are designed to reduce injuries in the event of a vehicle to a pedestrian collision. When a collision is detected the airbag will deploy and cover hard areas, such as a-pillars and bonnet edges, before they can be struck by the pedestrian. When introduced in 2012 the Volvo V40 included the world's first pedestrian airbag as standard. As a result, the V40 ranked highest (88%) in the EuroNCAP's pedestrian tests. Manufacturers Suppliers of SRS airbags include Autoliv, Daicel, TRW, and JSS (which owns Breed, Key Safety Systems, and Takata). The majority of impact sensors of airbags are manufactured by the Lanka Harness Company in Sri Lanka. == Operation ==

The airbags in the vehicle are controlled by a central airbag control unit (ACU), a specific type of ECU. The ACU monitors several related sensors within the vehicle, including accelerometers, impact sensors, side (door) pressure sensors, wheel speed sensors, gyroscopes, brake pressure sensors, and seat occupancy sensors. Oftentimes, ACUs log this—and other—sensor data in a circular buffer and record it to onboard non-volatile memory, to provide a snapshot of the crash event for investigators. As such, an ACU frequently functions as the vehicle's event data recorder (EDR); not all EDRs are ACUs, and not all ACUs include EDR features. An ACU typically includes capacitors within its circuitry, so that the module remains powered and able to deploy the airbags if the vehicle's battery connection to the ACU is severed during a crash. The bag itself and its inflation mechanism are concealed within the steering wheel boss (for the driver), or the dashboard (for the front passenger), behind plastic flaps or doors that are designed to tear open under the force of the bag inflating. Once the requisite threshold has been reached or exceeded, the airbag control unit will trigger the ignition of a gas generator propellant to rapidly inflate a fabric bag. As the vehicle occupant collides with and squeezes the bag, the gas escapes in a controlled manner through small vent holes. The airbag's volume and the size of the vents in the bag are tailored to each vehicle type, to spread out the deceleration of (and thus force experienced by) the occupant over time and over the occupant's body, compared to a seat belt alone. The signals from the various sensors are fed into the airbag control unit, which determines from them the angle of impact, the severity, or the force of the crash, along with other variables. Depending on the result of these calculations, the ACU may also deploy various additional restraint devices, such as seat belt pre-tensioners, and/or airbags (including frontal bags for driver and front passenger, along with seat-mounted side bags, and "curtain" airbags which cover the side glass). Each restraint device is typically activated with one or more pyrotechnic devices, commonly called an initiator or electric match. The electric match, which consists of an electrical conductor wrapped in a combustible material, activates with a current pulse between in less than 2 milliseconds. When the conductor becomes hot enough, it ignites the combustible material, which initiates the gas generator. In a seat belt pre-tensioner, this hot gas is used to drive a piston that pulls the slack out of the seat belt. In an airbag, the initiator is used to ignite solid propellant inside the airbag inflator. The burning propellant generates inert gas which rapidly inflates the airbag in approximately . An airbag must inflate quickly to be fully inflated by the time the forward-traveling occupant reaches its outer surface. Typically, the decision to deploy an airbag in a frontal crash is made within after the onset of the crash, and both the driver and passenger airbags are fully inflated within approximately after the first moment of vehicle contact. If an airbag deploys too late or too slowly, the risk of occupant injury from contact with the inflating airbag may increase. Since more distance typically exists between the passenger and the instrument panel, the passenger airbag is larger and requires more gas to fill it. Older airbag systems contained a mixture of sodium azide (), , and . A typical driver-side airbag contains approximately of , with the larger passenger-side airbag containing about . Within about 40 milliseconds of impact, all these components react in three separate reactions that produce nitrogen gas. The reactions, in order, are as follows. • • • The first two reactions create 4 molar equivalents of nitrogen gas, and the third converts the remaining reactants to relatively inert potassium silicate and sodium silicate. Modern airbags use guanidine nitrate to generate gas through the following reaction: : There are ongoing efforts to find alternative compounds so that airbags have less toxic reactants. The reaction of the Sr complex nitrate, () of carbohydrazide (SrCDH) with various oxidizing agents results in the evolution of and gases. The and gases evolved made up 99% of all gases evolved. Nearly all of the starting materials will not decompose until reaching temperatures of or higher, so this could be a viable option as an airbag gas generator. Since airbags deploy only once and deflate quickly after the initial impact, they will not be beneficial during a subsequent collision. In vehicles equipped with a rollover sensing system, accelerometers, and gyroscopes are used to sense the onset of a rollover event. If a rollover event is determined to be imminent, side-curtain airbags are deployed to help protect the occupant from contact with the side of the vehicle interior, and also to help prevent occupant ejection as the vehicle rolls over. Triggering conditions Airbags are designed to deploy in frontal and near-frontal collisions more severe than a threshold defined by the regulations governing vehicle construction in whatever particular market the vehicle is intended for: United States regulations require deployment in crashes at least equivalent in deceleration to a barrier collision, or similarly, striking a parked car of similar size across the full front of each vehicle at about twice the speed. International regulations are performance-based, rather than technology-based, so airbag deployment threshold is a function of overall vehicle design. Unlike crash tests into barriers, real-world crashes typically occur at angles other than directly into the front of the vehicle, and the crash forces usually are not evenly distributed across the front of the vehicle. Consequently, the relative speed between a striking and struck vehicle required to deploy the airbag in a real-world crash can be much higher than an equivalent barrier crash. Because airbag sensors measure deceleration, the vehicle speed is not a good indicator of whether an airbag should be deployed. Airbags can deploy due to the vehicle's undercarriage striking a low object protruding above the roadway due to the resulting deceleration. The airbag sensor is a MEMS accelerometer, which is a small integrated circuit with integrated micromechanical elements. The microscopic mechanical element moves in response to rapid deceleration, and this motion causes a change in capacitance, which is detected by the electronics on the chip that then sends a signal to fire the airbag. The most common MEMS accelerometer in use is the ADXL-50 by Analog Devices, but there are other MEMS manufacturers as well. Initial attempts using mercury switches did not work well. Before MEMS, the primary system used to deploy airbags was called a "rolamite". A rolamite is a mechanical device, consisting of a roller suspended within a tensioned band. As a result of the particular geometry and material properties used, the roller is free to translate with little friction or hysteresis. This device was developed at Sandia National Laboratories. Rolamite and similar macro-mechanical devices were used in airbags until the mid-1990s after which they were universally replaced with MEMS. Nearly all airbags are designed to automatically deploy in the event of a vehicle fire when temperatures reach . This safety feature, often termed auto-ignition, helps to ensure that such temperatures do not cause an explosion of the entire airbag module. Today, airbag triggering algorithms are much more complex, being able to adapt the deployment speed to the crash conditions, and prevent unnecessary deployments. The algorithms are considered valuable intellectual property. Experimental algorithms may take into account such factors as the weight of the occupant, the seat location, and seat belt use, as well as even attempt to determine if a baby seat is present. Inflation When the frontal airbags are to deploy, a signal is sent to the gas generator/inflator unit within the airbag control unit. An igniter starts a rapid chemical reaction generating primarily nitrogen gas () to fill the airbag making it deploy through the module cover. Some airbag technologies use compressed nitrogen or argon gas with a pyrotechnic operated valve ("hybrid gas generator"), while other technologies use various energetic propellants. Although propellants containing the highly toxic sodium azide () were common in early inflator designs, little to no toxic sodium azide has been found on used airbags. The azide-containing pyrotechnic gas generators contain a substantial amount of the propellant. The driver-side airbag would contain a canister containing about of sodium azide. The passenger side container holds about of sodium azide. From the onset of the crash, the entire deployment and inflation process is about 0.04 seconds. Because vehicles change speed so quickly in a crash, airbags must inflate rapidly to reduce the risk of the occupant hitting the vehicle's interior. Variable-force deployment Advanced airbag technologies are being developed to tailor airbag deployment to the severity of the crash, the size, and posture of the vehicle occupant, belt usage, and how close that person is to the actual airbag. Many of these systems use multi-stage inflators that deploy less forcefully in stages in moderate crashes than in very severe crashes. Occupant sensing devices let the airbag control unit know if someone is occupying a seat adjacent to an airbag, the mass/weight of the person, whether a seat belt or child restraint is being used, and whether the person is forward in the seat and close to the airbag. Based on this information and crash severity information, the airbag is deployed at either a high force level, a less forceful level, or not at all. Adaptive airbag systems may utilize multi-stage airbags to adjust the pressure within the airbag. The greater the pressure within the airbag, the more force the airbag will exert on the occupants as they come in contact with it. These adjustments allow the system to deploy the airbag with a moderate force for most collisions; reserving the maximum force airbag only for the severest of collisions. Additional sensors to determine the location, weight or relative size of the occupants may also be used. Information regarding the occupants and the severity of the crash are used by the airbag control unit, to determine whether airbags should be suppressed or deployed, and if so, at various output levels. airbag Post-deployment A chemical reaction produces a burst of nitrogen to inflate the bag. Once an airbag deploys, deflation begins immediately as the gas escapes through vent(s) in the fabric (or, as it is sometimes called, the cushion) and cools. Deployment is frequently accompanied by the release of dust-like particles, and gases in the vehicle's interior (called effluent). Most of this dust consists of cornstarch, french chalk, or talcum powder, which are used to lubricate the airbag during deployment. Newer designs produce effluent primarily consisting of harmless talcum powder/cornstarch and nitrogen gas. In older designs using an azide-based propellant (usually ), varying amounts of sodium hydroxide nearly always are initially present. In small amounts this chemical can cause minor irritation to the eyes and/or open wounds; however, with exposure to air, it quickly turns into sodium bicarbonate (baking soda). However, this transformation is not 100% complete, and invariably leaves residual amounts of hydroxide ions from NaOH. Depending on the type of airbag system, potassium chloride may also be present. For most people, the only effect the dust may produce is some minor irritation of the throat and eyes. Generally, minor irritations only occur when the occupant remains in the vehicle for many minutes with the windows closed and no ventilation. However, some people with asthma may develop a potentially lethal asthmatic attack from inhaling the dust. Because of the airbag exit flap design of the steering wheel boss and dashboard panel, these items are not designed to be recoverable if an airbag deploys, meaning that they have to be replaced if the vehicle has not been written off in a collision. Moreover, the dust-like particles and gases can cause irreparable cosmetic damage to the dashboard and upholstery, meaning that minor collisions that result in the deployment of airbags can be costly, even if there are no injuries and there is only minor damage to the vehicle structure. == Regulatory specifications ==

United States On 11 July 1984, the United States government amended Federal Motor Vehicle Safety Standard 208 (FMVSS 208) to require cars produced after 1 April 1989 to be equipped with a passive restraint for the driver. An airbag or an automatic seat belt would meet the requirements of the standard. Airbag introduction was stimulated by the National Highway Traffic Safety Administration. However, airbags were not mandatory on light trucks until 1997. In 1998, FMVSS 208 was amended to require dual front airbags, and reduced-power, second-generation airbags were also mandated. This was due to the injuries caused by first-generation airbags, though FMVSS 208 continues to require that bags be engineered and calibrated to be able to "save" the life of an unbelted 50th-percentile size and weight "male" crash test dummy. The technical performance and validation requirements for the inflator assembly used in airbag modules are specified in SAE USCAR 24–2. Europe Some countries outside North America adhere to internationalized European ECE vehicle and equipment regulations rather than the United States Federal Motor Vehicle Safety Standards. ECE airbags are generally smaller and inflate less forcefully than United States airbags because the ECE specifications are based on belted crash test dummies. The Euro NCAP vehicle safety rating encourages manufacturers to take a comprehensive approach to occupant safety; a good rating can only be achieved by combining airbags with other safety features. Almost every new car sold in Europe is equipped with front and side airbags, but in the European Union in 2020 and in the United Kingdom, and most other developed countries there is no direct legal requirement for new cars to feature airbags. Central and South America Ecuador requires dual front airbags in new car models since 2013. Since January 2014, except for micro vehicles, all new cars made or imported in Argentina must have front airbags. Since 1 January 2014, all new cars sold in Brazil must have dual front airbags. Since July 2014, all new cars sold in Uruguay must have dual front airbags. Since December 2016, all new cars sold in Chile must have dual front airbags. Since 1 January 2017, all cars made or imported in Colombia must have dual front airbags. Since 1 January 2020, all new cars sold in Mexico must have dual front airbags. India On 5 March 2021, the Indian Ministry of Road Transport and Highways mandated that all new vehicle models introduced in India after 1 April 2021 have dual front airbags; the regulation also requires that all existing models be equipped with dual front airbags by 31 August 2021. India also mandated that all passenger vehicles sold after October 2023 must have a minimum of six airbags. ==Maintenance==

Inadvertent airbag deployment while a vehicle is being serviced can result in serious injury, and an improperly installed or defective airbag unit may fail to operate as intended. For this reason, individuals servicing vehicles, as well as first responders, are required to account for the fact that some airbag control systems may remain powered for up to 30 minutes after a vehicle's battery has been disconnected. In some countries, the sale, transport, handling, and servicing of airbags and related components are subject to legal restrictions. In Germany, for example, airbags are regulated as hazardous explosive devices, and only trained auto mechanics are permitted to service airbag systems. Automaker policies regarding the service life of undeployed airbags vary. Some manufacturers, such as Mercedes-Benz, have historically recommended replacement after a specified period to ensure reliability. Certain Škoda vehicles have indicated an airbag service life of approximately 14 years from the date of manufacture, after which replacement may be uneconomical relative to the vehicle’s value. By contrast, Volvo has stated that airbags are designed to last for the lifetime of the vehicle, although this is not presented as an absolute guarantee of performance. == Limitations ==

of an underride guard at —the truck platform at head height has been prevented from impacting the windshield. Although the millions of installed airbags in use have an excellent safety record, some limitations on their ability to protect car occupants exist. The original implementation of front airbags did little to protect against side collisions, which can be more dangerous than frontal collisions because the protective crumple zone in front of the passenger compartment is completely bypassed. Side airbags and protective airbag curtains are increasingly being required in modern vehicles to protect against this very common category of collisions. Airbags are designed to deploy once only, so are ineffective if any further collisions occur after an initial impact. Multiple impacts may occur during rollovers or other incidents involving multiple collisions, such as many multivehicle collisions. An extremely dangerous situation occurs during "underride collisions", in which a passenger vehicle collides with the rear of a tractor-trailer lacking a rear underride guard, or hits the side of such a trailer not equipped with a side underride guard. The platform bed of a typical trailer is roughly at the head height of a seated adult occupant of a typical passenger car. This means not much of a barrier exists between a head and the edge of the trailer platform, except a glass windshield. In an underride collision, the car's crush zones designed to absorb collision energy are completely bypassed, and the airbags may not deploy in time because the car does not decelerate appreciably until the windshield and roof pillars have already impacted the trailer bed. Typical airbag systems are completely disabled by turning off the ignition key. Unexpected turnoffs usually also disable the engine, power steering, and power brakes, and can be the direct cause of a collision. If a violent collision occurs, the disabled airbags will not deploy to protect vehicle occupants. In 2014, General Motors admitted to concealing information about fatal collisions caused by defective ignition switches that would abruptly shut down a car (including its airbags). Between 13 and 74 deaths have been directly attributed to this defect, depending on how the fatalities are classified. == Injuries and fatalities ==

s and airbags in the United States of America over 10 years Under some rare conditions, airbags can injure and in some very rare instances kill vehicle occupants. To provide crash protection for occupants not wearing seat belts, United States airbag designs trigger much more forcefully than airbags designed to the international ECE standards used in most other countries. Recent "smart" airbag controllers can recognize if a seat belt is used, and alter the airbag cushion deployment parameters accordingly. In 1990, the first automotive fatality attributed to an airbag was reported. TRW produced the first gas-inflated airbag in 1994, with sensors and low inflation-force bags becoming common soon afterward. Dual-depth (also known as dual-stage) airbags appeared on passenger cars in 1998. By 2005, deaths related to airbags had declined, with no adult deaths and two child deaths attributed to airbags that year. However, injuries remain fairly common in collisions with airbag deployment. Serious injuries are less common, but severe or fatal injuries can occur to vehicle occupants very near an airbag or in direct contact when it deploys. Such injuries may be sustained by unconscious drivers slumped over the steering wheel, unrestrained or improperly restrained occupants who slide forward in the seat during precrash braking, and properly belted drivers sitting very close to the steering wheel. A good reason for the driver not to cross hands over the steering wheel, a rule taught to most learner drivers, but quickly forgotten by most, is that an airbag deployment while negotiating a turn may result in the driver's hand(s) being driven forcefully into their face, exacerbating any injuries from the airbag alone. A US study showed that the risk for a serious head injury occurring is 5.495% while travelling . The risk is reduced for passengers to 4.435%. This risk is lowered by 80.5% to 1.073% when using an airbag. The risk for passengers is lowered by 82% to 0.797%. The tests with the airbags were done at , faster than the tests without air bags. There is a 15.45% risk of serious injury to unprotected occupants at , this drops to 4.68% with protected occupants. This is a 69.7% decrease in change of serious injury, with the airbags deploying 96.1% of the time. Improvements in sensing and gas-generator technology have allowed the development of third-generation airbag systems that can adjust their deployment parameters to the size, weight, position, and restraint status of the occupant. These improvements have demonstrated a reduced injury risk factor for small adults and children, who had an increased risk of injury with first-generation airbag systems. One model of airbags made by the Takata Corporation used ammonium nitrate–based gas-generating compositions in airbag inflators instead of the more stable, but more expensive compound tetrazole. The ammonium nitrate-based inflators have a flaw where old inflators with long-term exposure to hot and humid climate conditions could rupture during deployment, projecting metal shards through the airbag and into the driver. As of December 2022, the defect has caused 33 deaths worldwide, with up to 24 in the U.S. and the remaining in Australia and Malaysia. The National Highway Traffic Safety Administration (NHTSA) recalled over 33 million vehicles in May 2015, and fined Takata $70 million in November 2015. Toyota, Mazda, and Honda have said that they will not use ammonium-nitrate inflators. In June 2017, Takata filed for bankruptcy. Airbag fatality statistics From 1990 to 2000, the United States NHTSA identified 175 fatalities caused by airbags. Most of these (104) have been children. About 3.3 million airbag deployments have occurred during that interval, and the agency estimates more than 6,377 lives were saved and countless injuries were prevented. A rear-facing infant restraint put in the front seat of a vehicle places an infant's head close to the airbag, which can cause severe head injuries or death if the airbag deploys. Some modern cars include a switch to disable the front-passenger airbag, in case a child-supporting seat is used there (although not in Australia, where rear-facing child seats are prohibited in the front where an airbag is fitted). In vehicles with side airbags, it is dangerous for occupants to lean against the windows, doors, and pillars, or to place objects between themselves and the side of the vehicle. Articles hung from a vehicle's clothes hanger hooks can be hazardous if the vehicle's side-curtain airbags are deployed. A seat-mounted airbag may also cause internal injury if the occupant leans against the door. == Aerospace and military applications ==

The aerospace industry and the United States government have applied airbag technologies for many years. NASA and United States Department of Defense have incorporated airbag systems in various aircraft and spacecraft applications as early as the 1960s. Spacecraft airbag landing systems airbag landing system on simulated Martian terrain The first use of airbags for landing were Luna 9 and Luna 13. As with later missions, these would use the airbags to bounce along the surface, absorbing landing energy. The Mars Pathfinder lander employed an innovative airbag landing system, supplemented with aerobraking, parachute, and solid rocket landing thrusters. This prototype successfully tested the concept, and the two Mars Exploration Rover Mission landers employed similar landing systems. The Beagle 2 Mars lander also tried to use airbags for landing; the landing was successful, and the lander touched down safely, but several of the spacecraft's solar panels failed to deploy, thereby disabling the spacecraft. The Boeing Starliner uses six airbags to cushion the ground landing of the crewed capsule. Aircraft airbag landing systems Airbags have also been used on military fixed-wing aircraft, such as the escape crew capsule of the F-111 Aardvark. Occupant protection The United States Army has incorporated airbags in its UH-60A/L Black Hawk and OH-58D Kiowa Warrior helicopter fleets. The Cockpit Air Bag System (CABS) consists of forward and lateral airbags, and an inflatable tubular structure (on the OH-58D only) with an Electronic Crash Sensor Unit (ECSU). The CABS system was developed by the United States Army Aviation Applied Technology Directorate, through a contract with Simula Safety Systems (now BAE Systems). It is the first conventional airbag system for occupant injury prevention (worldwide) designed and developed and placed in service for an aircraft, and the first specifically for helicopter applications. == Other uses ==

In the mid-1970s, the UK Transport Research Laboratory tested several types of motorcycle airbags. In 2006 Honda introduced the first production motorcycle airbag safety system on its Gold Wing motorcycle. Honda claims that sensors in the front forks can detect a severe frontal collision and decide when to deploy the airbag, absorbing some of the forward energy of the rider and reducing the velocity at which the rider may be thrown from the motorcycle. More commonly, air bag vests – either integrated into the motorcyclist's jacket or worn over it – have started to become used by regular riders on the street. MotoGP has made it compulsory since 2018 for riders to wear suits with integrated airbags. Similarly, companies such as Helite and Hit-Air have commercialized equestrian airbags, which attach to the saddle and are worn by the rider. Other sports, particularly skiing and snowboarding, have started introducing airbag safety mechanisms. File:Airbag backpack, IAA 2021, Munich (IAA10362).webm|Airbag for cycling File:Motorradairbag.JPG|Airbag on a motorcycle == See also ==