Sulfur

Physical properties Sulfur forms several polyatomic molecules. The best-known allotrope is octasulfur, cyclo-S8. The point group of cyclo-S8 is D4d and its dipole moment is 0 D. Octasulfur is a soft, bright-yellow solid that is odorless. It melts at , and boils at . The structure of the S8 ring is virtually unchanged by this phase transition, which affects the intermolecular interactions. Cooling molten sulfur freezes at , as it predominantly consists of the β-S8 molecules. Between its melting and boiling temperatures, octasulfur changes its allotrope again, turning from β-octasulfur to γ-sulfur, again accompanied by a lower density but increased viscosity due to the formation of polymers. Sulfur is insoluble in water but soluble in carbon disulfide and, to a lesser extent, in other nonpolar organic solvents, such as benzene and toluene. Sulfur is also soluble in supercritical carbon dioxide. Chemical properties Under normal conditions, sulfur hydrolyzes very slowly to mainly form hydrogen sulfide and sulfuric acid: {{multiple image|left|perrow = 1|total_width=100|align = left The reaction involves adsorption of protons onto clusters, followed by disproportionation into the reaction products. The second, fourth and sixth ionization energies of sulfur are 2252 kJ/mol, 4556 kJ/mol and 8495.8 kJ/mol, respectively. The composition of reaction products of sulfur with oxidants (and its oxidation state) depends on whether releasing of reaction energy overcomes these thresholds. Applying catalysts and/or supply of external energy may vary sulfur's oxidation state and the composition of reaction products. While reaction between sulfur and oxygen under normal conditions gives sulfur dioxide (oxidation state +4), formation of sulfur trioxide (oxidation state +6) requires a temperature of and presence of a catalyst. In reactions with elements of lesser electronegativity, it reacts as an oxidant and forms sulfides, where it has oxidation state −2. Sulfur reacts with nearly all other elements except noble gases, even with the notoriously unreactive metal iridium (yielding iridium disulfide). Some of those reactions require elevated temperatures. Allotropes Sulfur forms over 30 solid allotropes, more than any other element. Besides S8, several other rings are known. Removing one atom from the crown gives S7, which is of a deeper yellow than S8. HPLC analysis of "elemental sulfur" reveals an equilibrium mixture of mainly S8, but with S7 and small amounts of S6. Larger rings have been prepared, including S12 and S18. Amorphous or "plastic" sulfur is produced by rapid cooling of molten sulfur—for example, by pouring it into cold water. X-ray crystallography studies show that the amorphous form may have a helical structure with eight atoms per turn. The long coiled polymeric molecules make the brownish substance elastic, and in bulk it has the feel of crude rubber. This form is metastable at room temperature and gradually reverts to the crystalline molecular allotrope, which is no longer elastic. This process happens over a matter of hours to days, but can be rapidly catalyzed. Isotopes Sulfur has 23 known isotopes, four of which are stable: 32S (), 33S (), 34S (), and 36S (). It has been found that the proportion of the two most abundant sulfur isotopes 32S and 34S varies in different samples by a surprising large amount. Determination of the isotope ratio (δ34S) in the samples indicates their chemical history, and with support of other methods, it allows to age-date the samples, estimate temperature of equilibrium between ore and water, determine pH and oxygen fugacity, identify the activity of sulfate-reducing bacteria in the time of formation of the sample, or suggest the main sources of sulfur in ecosystems. However, there are ongoing discussions over the real reason for the δ34S shifts, biological activity or postdeposit alteration. For example, when sulfide minerals are precipitated, isotopic equilibration between solid and liquid may cause small differences in the δ34S values of co-genetic minerals. The differences between minerals can be used to estimate the temperature of equilibration. The δ13C and δ34S of coexisting carbonate minerals and sulfides can be used to determine the pH and oxygen fugacity of the ore-bearing fluid during ore formation. Scientists measure the sulfur isotopes of minerals in rocks and sediments to study the redox conditions in past oceans. Sulfate-reducing bacteria in marine sediment fractionate sulfur isotopes as they take in sulfate and produce sulfide. Prior to the 2010s, it was thought that sulfate reduction could fractionate sulfur isotopes up to 46 permil and fractionation larger than 46 permil recorded in sediments must be due to disproportionation of sulfur compounds in the sediment. This view has changed since the 2010s as experiments showed that sulfate-reducing bacteria can fractionate to 66 permil. As substrates for disproportionation are limited by the product of sulfate reduction, the isotopic effect of disproportionation should be less than 16 permil in most sedimentary settings. In forest ecosystems, sulfate is derived mostly from the atmosphere; weathering of ore minerals and evaporites contribute some sulfur. Sulfur with a distinctive isotopic composition has been used to identify pollution sources, and enriched sulfur has been added as a tracer in hydrologic studies. Differences in the natural abundances can be used in systems where there is sufficient variation in the 34S of ecosystem components. Rocky Mountain lakes thought to be dominated by atmospheric sources of sulfate have been found to have measurably different 34S values than lakes believed to be dominated by watershed sources of sulfate. The radioactive 35S is formed in cosmic ray spallation of the atmospheric 40Ar. This fact may be used to verify the presence of recent (less than a year old) atmospheric sediments in various materials. This isotope may be obtained artificially in different ways. In practice, the reaction 35Cl + n → 35S + p is used, irradiating potassium chloride with neutrons. The isotope 35S is used in various sulfur-containing compounds as a radioactive tracer for many biological studies, for example, the Hershey-Chase experiment. Because of the weak beta activity of 35S, its compounds are relatively safe as long as they are not ingested or absorbed by the body. Natural occurrence are due to elemental sulfur and sulfur compounds deposited by active volcanoes. , a volcano in East Java, Indonesia, 2009 32S is produced by stellar nucleosynthesis inside massive stars, at a depth where the temperature exceeds , by the fusion of one nucleus of silicon plus one nucleus of helium. Because this nuclear reaction is part of the alpha process, which produces highly abundant elements, sulfur is the 10th most common element in the universe. Sulfur, usually in the sulfide oxidation state, is present in many types of meteorites. Ordinary chondrites contain on average 2.1% sulfur, and carbonaceous chondrites may contain as much as 6.6%. It is normally present as troilite (FeS), but there are exceptions, with carbonaceous chondrites containing free sulfur, sulfates and other sulfur compounds. The distinctive colors of Jupiter's volcanic moon Io are attributed to various forms of molten, solid, and gaseous sulfur. In July 2024, elemental sulfur was accidentally discovered to exist on Mars after the Curiosity rover drove over and crushed a rock, revealing sulfur crystals inside it. Sulfur is the fifth most common element by mass in the Earth. Elemental sulfur can be found near hot springs and volcanic regions in many parts of the world, especially along the Pacific Ring of Fire; such volcanic deposits are mined in Indonesia, Chile, and Japan. These deposits are polycrystalline, with the largest documented single crystal measuring . Historically, Sicily was a major source of sulfur in the Industrial Revolution. Lakes of molten sulfur up to about in diameter have been found on the sea floor, associated with submarine volcanoes, at depths where the boiling point of water is higher than the melting point of sulfur. Native sulfur is synthesized by anaerobic bacteria acting on sulfate minerals such as gypsum in salt domes. Significant deposits in salt domes occur along the coast of the Gulf of Mexico, and in evaporites in eastern Europe and western Asia. Native sulfur may be produced by geological processes alone. Fossil-based sulfur deposits from salt domes were once the basis for commercial production in the United States, Russia, Turkmenistan, and Ukraine. Such sources have become of secondary commercial importance, and most are no longer worked but commercial production is still carried out in the Osiek mine in Poland. Common naturally occurring sulfur compounds include the sulfide minerals, such as pyrite (iron sulfide), cinnabar (mercury sulfide), galena (lead sulfide), sphalerite (zinc sulfide), and stibnite (antimony sulfide); and the sulfate minerals, such as gypsum (calcium sulfate), alunite (potassium aluminium sulfate), and barite (barium sulfate). On Earth, just as upon Jupiter's moon Io, elemental sulfur occurs naturally in volcanic emissions, including emissions from hydrothermal vents. Petroleum and natural gas are the main industrial sources of sulfur. ==Compounds==

Common oxidation states of sulfur range from −2 to +6. Sulfur forms stable compounds with all elements except the noble gases. Electron transfer reactions owes its blue color to a trisulfur radical anion () Sulfur polycations, , and are produced when sulfur is reacted with oxidizing agents in a strongly acidic solution. The colored solutions produced by dissolving sulfur in oleum were first reported as early as 1804 by C. F. Bucholz, but the cause of the color and the structure of the polycations involved was only determined in the late 1960s. is deep blue, is yellow and is red. This reaction highlights a distinctive property of sulfur: its ability to catenate (bind to itself by formation of chains). Protonation of these polysulfide anions produces the polysulfanes, H2Sx, where x = 2, 3, and 4. Ultimately, reduction of sulfur produces sulfide salts: The interconversion of these species is exploited in the sodium–sulfur battery. Hydrogenation Treatment of sulfur with hydrogen gives hydrogen sulfide. When dissolved in water, hydrogen sulfide is mildly acidic: Hydrogen sulfide gas and the hydrosulfide anion are extremely toxic to mammals, due to their inhibition of the oxygen-carrying capacity of hemoglobin and certain cytochromes in a manner analogous to cyanide and azide (see below, under precautions). Combustion The two principal sulfur oxides are obtained by burning sulfur: Many other sulfur oxides are observed including the sulfur-rich oxides include sulfur monoxide, disulfur monoxide, disulfur dioxides, and higher oxides containing peroxo groups. Halogenation Sulfur reacts with fluorine to give the highly reactive sulfur tetrafluoride and the highly inert sulfur hexafluoride. Whereas fluorine gives S(IV) and S(VI) compounds, chlorine gives S(II) and S(I) derivatives. Thus, sulfur dichloride, disulfur dichloride, and higher chlorosulfanes arise from the chlorination of sulfur. Sulfuryl chloride and chlorosulfuric acid are derivatives of sulfuric acid; thionyl chloride (SOCl2) is a common reagent in organic synthesis. Bromine also oxidizes sulfur to form sulfur dibromide and disulfur dibromide. Geoscientists also study the isotopes of metal sulfides in rocks and sediment to study environmental conditions in the Earth's past. Organic compounds File:L-Cystein - L-Cysteine.svg |(L)-Cysteine, an amino acid containing a thiol group File:, a proteinogenic amino acid|(L)-Methionine, an amino acid containing a thioether File:Thiamin.svg|Thiamine or vitamin B1 File:Biotin_structure.svg|Biotin or vitamin B7 File:Penicillin core.svg|Penicillin, an antibiotic ("R" is the variable group) File:Allicin skeletal.svg|Allicin, a chemical compound in garlic File:Diphenyl disulfide.svg|Diphenyl disulfide, a representative disulfide File:Dibenzothiophen - Dibenzothiophene.svg|Dibenzothiophene, a component of crude oil File:Perfluorooctanesulfonic acid structure.svg|Perfluorooctanesulfonic acid (PFOS), a surfactant Some of the main classes of sulfur-containing organic compounds include the following: • Thiols or mercaptans (so called because they capture mercury as chelators) are the sulfur analogs of alcohols; treatment of thiols with base gives thiolate ions. • Thioethers are the sulfur analogs of ethers. • Sulfonium ions have three groups attached to a cationic sulfur center. Dimethylsulfoniopropionate (DMSP) is one such compound, important in the marine organic sulfur cycle. • Sulfoxides and sulfones are thioethers with one and two oxygen atoms attached to the sulfur atom, respectively. The simplest sulfoxide, dimethyl sulfoxide, is a common solvent; a common sulfone is sulfolane. • Sulfonic acids are used in many detergents. Compounds with carbon–sulfur multiple bonds are uncommon, an exception being carbon disulfide, a volatile colorless liquid that is structurally similar to carbon dioxide. It is used as a reagent to make the polymer rayon and many organosulfur compounds. Unlike carbon monoxide, carbon monosulfide is stable only as an extremely dilute gas, found between solar systems. Organosulfur compounds are responsible for some of the unpleasant odors of decaying organic matter. They are widely known as the odorant in domestic natural gas, garlic odor, and skunk spray, as well as a component of bad breath odor. Not all organic sulfur compounds smell unpleasant at all concentrations: the sulfur-containing monoterpenoid grapefruit mercaptan in small concentrations is the characteristic scent of grapefruit, but has a generic thiol odor at larger concentrations. Sulfur mustard, a potent vesicant, was used in World War I as a disabling agent. Sulfur–sulfur bonds are a structural component used to stiffen rubber, similar to the disulfide bridges that rigidify proteins (see biological below). In the most common type of industrial "curing" or hardening and strengthening of natural rubber, elemental sulfur is heated with the rubber to the point that chemical reactions form disulfide bridges between isoprene units of the polymer. This process, patented in 1843, made rubber a major industrial product, especially in automobile tires. Because of the heat and sulfur, the process was named vulcanization, after the Roman god of the forge and volcanism. ==History==

Antiquity collection According to the Ebers Papyrus, a sulfur ointment was used in ancient Egypt to treat granular eyelids. Sulfur was used for fumigation in preclassical Greece; this is mentioned in the Odyssey. Pliny the Elder discusses sulfur in his Natural History, saying that its best-known source is the island of Melos. He mentions its use for fumigation, medicine, and bleaching cloth. A natural form of sulfur known as was known in China since the 6th century BC and found in Hanzhong. By the 3rd century, the Chinese had discovered that sulfur could be extracted from pyrite. }} English translations of the Christian Bible referred to sulfur as "brimstone". Indian alchemists, practitioners of the "science of chemicals" (), wrote extensively about the use of sulfur in alchemical operations with mercury, from the eighth century AD onwards. In the rasa shastra| tradition, sulfur is called "the smelly" (, ). Early European alchemists gave sulfur an alchemical symbol of a triangle atop a cross (🜍). Another type of sulfur used in alchemy, black sulfur (sulfur nigrum), also had its own symbol combining a two-barred cross atop a lemniscate (🜏). Black sulfur, also known as grey sulfur (sulfur griseum) or "horse brimstone" (sulfur caballinum), was a grey, impure form of sulfur, usually the dregs of sulfur purification, which was used for medicinal purposes despite often containing arsenic. In traditional skin treatment, elemental sulfur was used (mainly in creams) to alleviate such conditions as scabies, ringworm, psoriasis, eczema, and acne. The mechanism of action is unknown—though elemental sulfur does oxidize slowly to sulfurous acid, a mild reducing and antibacterial agent. Modern times activity; in the past it was used against acne vulgaris, rosacea, seborrheic dermatitis, dandruff, pityriasis versicolor, scabies, and warts. This 1881 advertisement baselessly claims efficacy against rheumatism, gout, baldness, and graying of hair. Sulfur appears in a column of fixed (non-acidic) alkali in a chemical table of 1718. Antoine Lavoisier used sulfur in combustion experiments, writing of some of these in 1777. Sulfur deposits in Sicily were the dominant source for more than a century. By the late 18th century, about 2,000 tonnes per year of sulfur were imported into Marseille, France, for the production of sulfuric acid for use in the Leblanc process. In industrializing Britain, with the repeal of tariffs on salt in 1824, demand for sulfur from Sicily surged. The increasing British control and exploitation of the mining, refining, and transportation of sulfur, coupled with the failure of this lucrative export to transform Sicily's backward and impoverished economy, led to the Sulfur Crisis of 1840, when King Ferdinand II gave a monopoly of the sulfur industry to a French firm, violating an earlier 1816 trade agreement with Britain. A peaceful solution was eventually negotiated by France. In 1867, elemental sulfur was discovered in underground deposits in Louisiana and Texas. The highly successful Frasch process was developed to extract this resource. In the late 18th century, furniture makers used molten sulfur to produce decorative inlays. Molten sulfur is sometimes still used for setting steel bolts into drilled concrete holes where high shock resistance is desired for floor-mounted equipment attachment points. Pure powdered sulfur was used as a medicinal tonic and laxative. In recent times, the main source of sulfur has become petroleum and natural gas. This is due to the requirement to remove sulfur from fuels in order to prevent acid rain, and has resulted in a surplus of sulfur. On the other hand, sulfur was the form eventually chosen in the United States, though multiple place names (such as White Sulphur Springs) use -ph-. Canada uses both spellings. IUPAC adopted the spelling sulfur in 1990 as did the Nomenclature Committee of the Royal Society of Chemistry in 1992, restoring the spelling sulfur to Britain. Oxford Dictionaries note that "in chemistry and other technical uses ... the -f- spelling is now the standard form for this and related words in British as well as US contexts, and is increasingly used in general contexts as well." ==Production==

, East Java, Indonesia. This image shows the dangerous and rugged conditions the miners face, including toxic smoke and high drops, as well as their lack of protective equipment. The pipes over which they are standing are for condensing sulfur vapors. Sulfur may be found by itself and historically was usually obtained in this form; pyrite has also been a source of sulfur. In volcanic regions in Sicily, in ancient times, it was found on the surface of the Earth, and the "Sicilian process" was used: sulfur deposits were piled and stacked in brick kilns built on sloping hillsides, with airspaces between them. Then, some sulfur was pulverized, spread over the stacked ore and ignited, causing the free sulfur to melt down the hills. Eventually the surface-borne deposits played out, and miners excavated veins that ultimately dotted the Sicilian landscape with labyrinthine mines. Mining was unmechanized and labor-intensive, with pickmen freeing the ore from the rock, and mine-boys or carusi carrying baskets of ore to the surface, often through a mile or more of tunnels. Once the ore was at the surface, it was reduced and extracted in smelting ovens. The conditions in Sicilian sulfur mines were horrific, prompting Booker T. Washington to write "I am not prepared just now to say to what extent I believe in a physical hell in the next world, but a sulfur mine in Sicily is about the nearest thing to hell that I expect to see in this life." Sulfur is still mined from surface deposits in poorer nations with volcanoes, such as Indonesia, and problems with working conditions still exist. Elemental sulfur was extracted from salt domes (where it sometimes occurs in nearly pure form) until the late 20th century, when it became a side product of other industrial processes such as in oil refining, in which sulfur is undesirable. As a mineral, native sulfur under salt domes is thought to be a fossil mineral resource, produced by the action of anaerobic bacteria on sulfate deposits. It was removed from such salt-dome mines mainly by the Frasch process. , stockpiled for shipment in North Vancouver, British Columbia Since then, sulfur has typically been produced from petroleum, natural gas, and related fossil resources, from which it is obtained mainly as hydrogen sulfide. Another way of storing sulfur is as a binder for concrete, the resulting product having some desirable properties (see sulfur concrete). The world production of sulfur in 2011 amounted to 69 million tonnes (Mt), with more than 15 countries contributing more than 1 Mt each. Countries producing more than 5 Mt are China (9.6), the United States (8.8), Canada (7.1) and Russia (7.1). Production has been slowly increasing from 1900 to 2010; the price was unstable in the 1980s and around 2010. ==Applications==

Sulfuric acid Elemental sulfur is used mainly as a precursor to other chemicals. Approximately 85% (1989) is converted to sulfuric acid (H2SO4): : In 2010, the United States produced more sulfuric acid than any other inorganic industrial chemical. The principal use for the acid is the extraction of phosphate ores for the production of fertilizer manufacturing. Other applications of sulfuric acid include oil refining, wastewater processing, and mineral extraction. One of the uses of elemental sulfur is in vulcanization of rubber, where polysulfide chains crosslink organic polymers. Large quantities of sulfites are used to bleach paper and to preserve dried fruit. Many surfactants and detergents (e.g. sodium lauryl sulfate) are sulfate derivatives. Calcium sulfate, gypsum (CaSO4·2H2O) is mined on the scale of 100 million tonnes each year for use in Portland cement and fertilizers. When silver-based photography was widespread, sodium and ammonium thiosulfate were widely used as "fixing agents". Sulfur is a component of gunpowder ("black powder"). Fertilizer Amino acids synthesized by living organisms such as methionine and cysteine contain organosulfur groups (thioester and thiol respectively). The antioxidant glutathione protecting many living organisms against free radicals and oxidative stress also contains organic sulfur. Some crops such as onion and garlic also produce different organosulfur compounds such as syn-propanethial-S-oxide responsible of lacrymal irritation (onions), or diallyl disulfide and allicin (garlic). Sulfates, commonly found in soils and groundwaters are often a sufficient natural source of sulfur for plants and bacteria. Atmospheric deposition of sulfur dioxide (SO2) is also a common artificial source (coal combustion) of sulfur for the soils. Under normal circumstances, in most agricultural soils, sulfur is not a limiting nutrient for plants and microorganisms (see Liebig's barrel). However, in some circumstances, soils can be depleted in sulfate, e.g. if this later is leached by meteoric water (rain) or if the requirements in sulfur for some types of crops are high. This explains that sulfur is increasingly recognized and used as a component of fertilizers. The most important form of sulfur for fertilizer is calcium sulfate, commonly found in nature as the mineral gypsum (CaSO4·2H2O). Elemental sulfur is hydrophobic (not soluble in water) and cannot be used directly by plants. Elemental sulfur (ES) is sometimes mixed with bentonite to amend depleted soils for crops with high requirement in organo-sulfur. Over time, abiotic processes involving atmospheric oxygen as well as biological processes involving soil bacteria can oxidize and convert elemental sulfur to soluble compounds, which can in turn be used by microorganisms and plants. Sulfur improves the efficiency of other essential plant nutrients, particularly nitrogen and phosphorus. Biologically produced sulfur particles are naturally hydrophilic due to a biopolymer coating and are easier to disperse over the land in a spray of diluted slurry, resulting in a faster uptake by plants. The plant requirement for sulfur equals or exceeds the requirement for phosphorus. It is an essential nutrient for plant growth, root nodule formation of legumes, and immunity and defense systems. Sulfur deficiency has become widespread in many countries in Europe. Because atmospheric inputs of sulfur continue to decrease, the deficit in the sulfur input/output is likely to increase unless sulfur fertilizers are used. Atmospheric inputs of sulfur decrease because of actions taken to limit acid rains. It has similar applications and is used as a fungicide against mildew and other mold-related problems with plants and soil. Elemental sulfur powder is used as an "organic" (i.e., "green") insecticide (actually an acaricide) against ticks and mites. A common method of application is dusting the clothing or limbs with sulfur powder. A diluted solution of lime sulfur (made by combining calcium hydroxide with elemental sulfur in water) is used as a dip for pets to destroy ringworm (fungus), mange, and other dermatoses and parasites. Sulfur candles of almost pure sulfur were burned to fumigate structures and wine barrels, but are now considered too toxic for residences. Pharmaceuticals Sulfur (specifically octasulfur, S8) is used in pharmaceutical skin preparations for the treatment of acne and other conditions. It acts as a keratolytic agent and also kills bacteria, fungi, scabies mites, and other parasites. Precipitated sulfur and colloidal sulfur are used, in form of lotions, creams, powders, soaps, and bath additives, for the treatment of acne vulgaris, acne rosacea, and seborrhoeic dermatitis. Many drugs contain sulfur. Early examples include antibacterial sulfonamides, known as sulfa drugs. A more recent example is mucolytic acetylcysteine. Sulfur is a part of many bacterial defense molecules. Most β-lactam antibiotics, including the penicillins, cephalosporins and monobactams contain sulfur. ==Biological role==

Sulfur is an essential component of all living cells. It is the eighth most abundant element in the human body by weight, about equal in abundance to potassium, and slightly greater than sodium and chlorine. A human body contains about of sulfur. The main dietary source of sulfur for humans is sulfur-containing amino acids, which can be found in plant and animal proteins. Transferring sulfur between inorganic and biomolecules In the 1880s, while studying Beggiatoa (a bacterium living in a sulfur rich environment), Sergei Winogradsky found that it oxidized hydrogen sulfide (H2S) as an energy source, forming intracellular sulfur droplets. Winogradsky referred to this form of metabolism as inorgoxidation (oxidation of inorganic compounds). Another contributor, who continued to study it was Selman Waksman. Primitive bacteria that live around deep ocean volcanic vents oxidize hydrogen sulfide for their nutrition, as discovered by Robert Ballard. They depend on enzymes such as sulfur oxygenase and sulfite oxidase to oxidize sulfur to sulfate. Some lithotrophs can even use the energy contained in sulfur compounds to produce sugars, a process known as chemosynthesis. Some bacteria and archaea use hydrogen sulfide in place of water as the electron donor in chemosynthesis, a process similar to photosynthesis that produces sugars and uses oxygen as the electron acceptor. Sulfur-based chemosynthesis may be simplifiedly compared with photosynthesis: There are bacteria combining these two ways of nutrition: green sulfur bacteria and purple sulfur bacteria. Also sulfur-oxidizing bacteria can go into symbiosis with larger organisms, enabling the later to use hydrogen sulfide as food to be oxidized. Example: the giant tube worm. There are sulfate-reducing bacteria, that, by contrast, "breathe sulfate" instead of oxygen. They use organic compounds or molecular hydrogen as the energy source. They use sulfur as the electron acceptor, and reduce various oxidized sulfur compounds back into sulfide, often into hydrogen sulfide. They can grow on other partially oxidized sulfur compounds (e.g. thiosulfates, thionates, polysulfides, sulfites). There are studies pointing that many deposits of native sulfur in places that were the bottom of the ancient oceans have biological origin. These studies indicate that this native sulfur have been obtained through biological activity, but what is responsible for that (sulfur-oxidizing bacteria or sulfate-reducing bacteria) is still unknown for sure. Sulfur is absorbed by plants roots from soil as sulfate and transported as a phosphate ester. Sulfate is reduced to sulfide via sulfite before it is incorporated into cysteine and other organosulfur compounds. While the plants' role in transferring sulfur to animals by food chains is more or less understood, the role of sulfur bacteria is just getting investigated. Protein and organic metabolites In all forms of life, most of the sulfur is contained in two proteinogenic amino acids (cysteine and methionine), thus the element is present in all proteins that contain these amino acids. Some of the sulfur is present in certain metabolites—many of which are cofactors—and sulfated polysaccharides of connective tissue (chondroitin sulfates, heparin). The functionality of a given protein is heavily dependent on its structure. Proteins reach this structure through the process of protein folding, which is facilitated by a variety of intra- and inter-molecular bonds. While much of the folding is driven by the formation of hydrogen bonds, covalent bonding of cysteine residues into disulfide bridges imposes constraints that stabilize particular conformations while preventing others from forming. As the bond energy of a covalent disulfide bridge is higher than the energy of a coordinate bond or hydrophobic interaction, greater numbers of disulfide bridges lead to higher energies required for protein denaturation. Disulfide bonds often serve to stabilize protein structures in the more oxidizing conditions of the extracellular environment. Within the cytoplasm, disulfide bonds may instead be reduced (i.e. in -SH form) to their constituent cysteine residues by thioredoxins. Many important cellular enzymes use prosthetic groups ending with sulfhydryl (-SH) moieties to handle reactions involving acyl-containing biochemicals: two common examples from basic metabolism are coenzyme A and alpha-lipoic acid. Cysteine-related metabolites homocysteine and taurine are other sulfur-containing amino acids that are similar in structure, but not coded by DNA, and are not part of the primary structure of proteins, take part in various locations of mammalian physiology. Two of the 13 classical vitamins, biotin and thiamine, contain sulfur, and serve as cofactors to several enzymes. In intracellular chemistry, sulfur operates as a carrier of reducing hydrogen and its electrons for cellular repair of oxidation. Reduced glutathione, a sulfur-containing tripeptide, is a reducing agent through its sulfhydryl (–SH) moiety derived from cysteine. Methanogenesis, the route to most of the world's methane, is a multistep biochemical transformation of carbon dioxide. This conversion requires several organosulfur cofactors. These include coenzyme M, , the immediate precursor to methane. Metalloproteins and inorganic cofactors Metalloproteins—in which the active site is a transition metal ion (or metal-sulfide cluster) often coordinated by sulfur atoms of cysteine residues—are essential components of enzymes involved in electron transfer processes. Examples include plastocyanin (Cu2+) and nitrous oxide reductase (Cu–S). The function of these enzymes is dependent on the fact that the transition metal ion can undergo redox reactions. Other examples include many zinc proteins, as well as iron–sulfur clusters. Most pervasive are the ferrodoxins, which serve as electron shuttles in cells. In bacteria, the important nitrogenase enzymes contain an Fe–Mo–S cluster and is a catalyst that performs the important function of nitrogen fixation, converting atmospheric nitrogen to ammonia that can be used by microorganisms and plants to make proteins, DNA, RNA, alkaloids, and the other organic nitrogen compounds necessary for life. Sulfur is also present in molybdenum cofactor. : Sulfate Deficiency In humans methionine is an essential amino acid; cysteine is conditionally essential and may be synthesized from non-essential serine via sulfur salvaged from methionine. Sulfur deficiency is uncommon due to the ubiquity of cysteine and methionine in food. Isolated sulfite oxidase deficiency is a rare, fatal genetic disease caused by mutations to sulfite oxidase, which is needed to metabolize sulfites to sulfates. ==Precautions==

}} Though elemental sulfur is only minimally absorbed through the skin and is of low toxicity to humans, inhalation of sulfur dust or contact with eyes or skin may cause irritation. Excessive ingestion of sulfur can cause a burning sensation or diarrhea, and cases of life-threatening metabolic acidosis have been reported after patients deliberately consumed sulfur as a folk remedy. Toxicity of sulfur compounds When sulfur burns in air, it produces sulfur dioxide. In water, this gas produces sulfurous acid and sulfites; sulfites are antioxidants that inhibit growth of aerobic bacteria and a useful food additive in small amounts. At high concentrations these acids harm the lungs, eyes, or other tissues. In organisms without lungs such as insects, sulfite in high concentration prevents respiration. Sulfur trioxide (made by catalysis from sulfur dioxide) and sulfuric acid are similarly highly acidic and corrosive in the presence of water. Concentrated sulfuric acid is a strong dehydrating agent that can strip available water molecules and water components from sugar and organic tissue. The burning of coal and/or petroleum by industry and power plants generates sulfur dioxide (SO2) that reacts with atmospheric water and oxygen to produce sulfurous acid (H2SO3). These acids are components of acid rain, lowering the pH of soil and freshwater bodies, sometimes resulting in substantial damage to the environment and chemical weathering of statues and structures. Fuel standards increasingly require that fuel producers extract sulfur from fossil fuels to prevent acid rain formation. This extracted and refined sulfur represents a large portion of sulfur production. In coal-fired power plants, flue gases are sometimes purified. More modern power plants that use synthesis gas extract the sulfur before they burn the gas. Hydrogen sulfide is about one-half as toxic as hydrogen cyanide, and intoxicates by the same mechanism (inhibition of the respiratory enzyme cytochrome oxidase), though hydrogen sulfide is less likely to cause sudden poisonings from small inhaled amounts (near its permissible exposure limit (PEL) of 20 ppm) because of its disagreeable odor. However, its presence in ambient air at concentration over 100–150 ppm quickly deadens the sense of smell, and a victim may breathe increasing quantities without noticing until severe symptoms cause death. Dissolved sulfide and hydrosulfide salts are toxic by the same mechanism. ==Notes==