The Scandinavian influence The
Norsemen were skilled seamen and boat builders and their boat designs depended on their needs. Trading vessels were wide, to allow large cargo storage, while raiding boats were long and narrow and very fast. They all used the
clinker fashion of planking, i.e. the planks overlapped one another. The boats used for fishing were scaled-down versions of their cargo boats. The
Scandinavian influence affected boat building long after the Viking period came to an end.
Yoles from the Orkney
Island of Stroma were built in the same way as the Norse boats. Early Scottish boat builders copied the Scandinavian designs with their clinker planking and characteristic sharp stems and sterns.
The Skaffie From the beginning of the 19th century a class of boat called the Skaffie appeared. These were favoured mainly in the
Moray Firth region. The early skaffie boats were small with rounded stems and raked sterns. They were two-masted with a tall dipping lugsail and a mizzen sail. Their short keel gave them good manoeuvrability in good weather, but they tended to be unstable in bad weather. They were usually crewed by around six people. Above all, though, they were light enough to be hauled up on to the beaches. The boats were un-decked and provided no shelter for the crew. Because of the vulnerability of the boats, they stayed only a few miles out to sea in full view of the land. These boats were gradually built bigger and could be around long, and partially decked. This came about because the harbours that were constructed from the mid to late 19th century meant that the boats no longer needed to be beached. Skaffies were not built in any great numbers after 1900.
The Fifie The "Fifie" then became the predominant fishing boat on the Scottish east coast. They were used from the 1850s until well into the 20th century. Fifies had a vertical stem and stern with a broad beam, which made them very stable. Their long keel was a disadvantage, especially manoeuvring in confined spaces. These boats were two masted with a main dipping lugsail and a mizzen sail. The masts were set quite far forward and aft to release a good working space. Fifies built from 1860 onwards were all decked, and from the 1870s onwards the bigger boats were built with
carvel planking, i.e. the planks were laid edge-to-edge instead of the overlapping clinker style of previous boats. Some boats were now being built up to about in length and were very fast.
The Zulu . In 1879,
Lossiemouth fisherman, William "Dad" Campbell came up with a radical design for his new boat. It had the vertical stem of the Fifie and the steeply raked stern of the Skaffie, and he called this boat
Nonesuch, registration number INS 2118. She was relatively small, overall with a . The
Nonesuch had her registration closed on 12 January 1901 after having been broken up. The
Zulu War raging in
South Africa at the time gave the name to this new class of boat. The Zulu boats were built to the
carvel method of planking. The shape of the Zulus gave the boats a long deck but a shorter keel, which greatly improved their manoeuvrability. Zulus were two-masted boats and carried three sails – a dipping
lug fore, a standing lug mizzen and a jib. The sails were very heavy and difficult to haul, and the masts had to be very long and strong. Masts could be tall on boats of in length. Their design produced very fast boats that became invaluable to herring fishing fleets. They got to the fishing grounds quickly and returned swiftly with the catch. Because of these qualities, the Zulus rapidly became very popular along the entire east coast. As the 20th century approached, steam capstans were introduced, and this made the hauling of the sails and nets much easier for the crews. One of the best of those was the capstans patented and built by MacDonald Brothers of
Portsoy, in 1908.
The steam boat The earliest steam powered fishing boats first appeared in the 1890s and used the
trawl system of fishing as well as lines and drift nets. These were large boats, usually in length with a beam of around . They weighed 40–50 tons and travelled at . The first steam boats were made of wood, but steel hulls were soon introduced and were divided into watertight compartments. They were well designed for the crew with a large building that contained the wheelhouse and the deckhouse. The boats built in the 20th century only had a mizzen sail, which was used to help steady the boat when its nets were out. The main function of the mast was now as a crane for lifting the catch ashore. They also had a steam capstan on the foredeck near the mast for hauling nets. The boats had narrow, high funnels so that the steam and thick coal smoke was released high above the deck and away from the fishermen. These funnels were nicknamed
woodbines because they looked like the popular brand of cigarette. These boats had a crew of twelve made up of a skipper, driver, fireman (to look after the boiler) and nine deck hands. The earliest purpose built fishing vessels were designed and made by David Allan (Born 1840 Orkney)In Leith in March 1875, he converted a drifter to steam power.In 1877 it is said that he built the first screw propelled steam trawler in the world. This vessel was
Pioneer LH854.She was of wooden construction with two masts and carried a gaff rigged main and mizen using booms, and a single foresail. Pioneer is mentioned in the Shetland Times of 4 May 1877. In 1878 he completed three steam-powered trawlers:
Forward for Methven of Leith and
Onward for Sharp and Murray of Cellardyke. In an interview with the Scotsman Mr. Allan stated that his motivation for auxiliary power was to increase the safety of fishermen. However local fishermen saw power trawling as a threat, remember that local boats of this period were or so, Mr. Allan's largest were . Some landowners questioned the sustainability of fish stocks to power trawlers. The Lammas Drive of 1878 states" It was reported that D. Allan of Granton had built two steam drifters the Forward and the Onward. The latter was unable to get a Celardyke crew so she fished from Aberdeen." During this time Mr. Allan was also skippering the boats to ensure that they were successful in their catches. In total he built ten boats at Leith between 1877 and 1881. Twenty-one boats were completed at Granton, his last vessel being
Degrave in 1886. Because of the prejudices mentioned, most of these were sold to foreign owners, France, Belgium, Spain and the West Indies amongst them. A full, complete account of his ventures can be found on Grantontrawlers.com. David Allan was buried on Christmas Day in South Shields in 1911. On page 14 of the
Daily Mirror of 27 December 1911 there is a photograph and a line drawing of
Onward. It reads "The death was announced in South Shields of Mr David Allan, the founder of the steam fishing industry. In 1877 he designed and built the steam Drifter Onward especially for fishing purposes. He afterwards commanded and worked the vessel himself." Steam fishing boats had many advantages. They were usually about than the sailing vessels so they could carry more nets and catch more fish. This was important, as the market was growing quickly at the beginning of the 20th century. They could travel faster and further and with greater freedom from weather, wind and tide. Because less time was spent travelling to and from the fishing grounds, more time could be spent fishing. The steam boats also gained the highest prices for their fish, as they could return quickly to harbour with their fresh catch. The main disadvantage of the steam boats, though, was their high operating costs. Their engines were mechanically inefficient and took up much space, while fuel and fitting out costs were very high. Before the
First World War, building costs were between £3,000 and £4,000, at least three times the cost of the sail boats. To cover these high costs, they needed to fish for longer seasons. The higher expenses meant that more steam drifters were company-owned or jointly owned. As the herring fishing industry declined, steam boats became too expensive.
The seine netter Petrol and paraffin engines began to be used in 1906. At first, they were mainly fitted to smaller boats of between in length, and they provided auxiliary power to assist the sails. However, as diesel engines became more powerful, the sails were replaced altogether, and the engines were fitted in larger and larger boats. Motor engines were relatively cheap, making them affordable to individual Fishermen. Early engines cost less than £100, and fuel costs were low. These boats also needed less maintenance than steam vessels. The two most popular engine brands were the Gardiner and Kelvin engines. The compact engines meant they could be fitted to existing sailing drifters such as Fifies and Zulus. The traditional Fifie style was better suited to the installation of a motor, which led to the custom building of a number of modified Fifie design boats with motors. In 1920, though, the government changed the rules by removing the guaranteed price for the herring and prices dropped dramatically. In 1921, some Lossiemouth skippers noticed that the
Danish seine net boats were landing huge quantities of plaice and other white fish at the English east coast ports. Their interest resulted in a few buying some seine nets and winches and trying this form of fishing. As they perfected seine net fishing, more of the Lossiemouth fleet converted to seine net. But boat design for this type of fishing was still proving to be an obstacle. That, and the cost of the majority steam boats prompted a new style of fishing boat. John Campbell, nephew of William Campbell who designed the first Zulu boat built a wooden boat that resembled, to some extent, the "Fifie" but had a broad beam. His boat, the
Marigold, did very well and over a relatively short period the entire Lossiemouth fleet (the first in Scotland) converted to the seine net. Other east coast ports followed on very quickly.
The trawler Today,
trawl fishing is the main industrial method of catching white fish. These
trawlers can catch and store massive amounts of fish. They possess highly sensitive electronic equipment and remove the chance element from fishing. They operate by trawling the nets along the sea bed where the kind of fish they want to catch are located.
Modern fishing methods Fishing for demersal species (fish occurring near the seabed) Bottom trawling – single boat This the commonest of the towed fishing gear; it is also known as "otter
trawling".
Trawl nets are shaped like a funnel with the sides extended ahead to guide the fish into the net. Otter boards (sometimes called "
doors") spread the towing wires and keep the net open horizontally. The mouth of the net is held open vertically by the use of floats attached to the headline, while weight distributed along the ground rope allows the net to make good contact with the sea floor. The otter boards would scrape along the seabed making noises that attract fish. The fish would congregate between the boards keeping up with them until they tired and the net would then overtake them. This method is used mainly to catch the demersal species such as cod, haddock, whiting and flatfish. The boats themselves can be less than 10 metres in length for inshore fishing to 60 metres or more for deep sea fishing. With the decline in the volumes of roundfish, the growth in fishing for high-priced species such as monkfish and
flatfish is being seen. In this case, scraper trawls are used. The nets are shaped differently with a lower headline, longer wings allowing a greater area to be swept.
Bottom trawling – two boats In pair trawling, each boat has a wire fastened to the net. Because of this, otterboards are not required to hold the mouth of the net open, as the boats maintain at their maximum a distance apart of around . The boats, because they share the load, can be smaller and less powerful yet can tow relatively large gear. These boats can be anything from 15 to 30 metres in length and have a typical combined power of . Again, this form of fishing is mainly for demersal species.
Seine netting Scottish seining, sometimes called fly dragging, has the net attached to two long ropes usually made of leaded polypropylene and around 3 km in length. The net is deployed in a triangular fashion with the first rope attached to a marker buoy, the dhan, to which the boat returns to complete the set. Both ropes are then winched in as the boat steams ahead slowly. Winch speed is gradually increased as the net gets closer to keep the net moving forward and also to herd the fish into the net. Like the trawl, floats and weighted footrope keep the mouth of the net open and in contact with the seabed. This method of fishing takes place on grounds on the continental shelf and not in deep sea. Seine netting is for all forms of whitefish.
Twin beam trawling The beam trawl is one where a beam, up to 12 metres in length, is attached to a skid at each end. The beam is situated on top of the skids effectively keeping the top of the net open and the fish are channelled between the skids. Two beam trawls are deployed alongside each other from outrigger booms on each side of the boat. This method is primarily for taking flatfish but these vessels can be used also for scallop dredging.
Twin rig trawl This method is to use two trawls side by side. Three wires attach to this combination. Instead of having individual wires connected to each of the nets sides, a common wire attaches to the two inner sides and the outer sides of each net are wired individually. Again otter boards allow the net mouths to spread apart horizontally while floats and ground ropes provide the vertical forces. This gear is usually used for catching target fish such as monkfish, flatfish and nephrops.
Line fishing Line fishing used no nets. Line fishing boats harnessed a single line, up to a kilometre long, that was trailed behind the vessel. At intervals along that line drop lines were suspended at the end of which was tied a large hook onto which bait was hung. Halibut, cod, haddock,
lemon sole, ling and skate were the predominant prey. The line would be released and reeled in using winches. The largest line fishing boat in the Scottish fleet was the Radiation which sailed out of Aberdeen and which predominantly fished Icelandic and
Faroe Isles' waters.
Fishing for pelagic species (fish occurring in mid and upper water) Pelagic gears are designed to catch species such as herring, mackerel, scad, blue whiting and sprats. However pelagic fishing from boats from the Scottish east coast ports normally catch herring and an amount of blue whiting from the northern North Sea.
Methods • Single boat pelagic trawl – similar to the demersal trawl but the gear is generally lighter, as it does not have to cope with dragging across the seabed. • Pelagic pair trawling – operate in a similar method to the demersal pair trawl and again with lighter gear. ==Ancillary industries==