MarketMedway watermills (lower tributaries)
Company Profile

Medway watermills (lower tributaries)

The River Medway and its tributaries and sub-tributaries have been used for more than 1,150 years as a source of power. There are over two hundred sites where the use of water power is known. Many different processes were performed by the use of water power:- corn milling, fulling, paper making, iron smelting, pumping water, making gunpowder, vegetable-oil extraction, and electricity generation. Today, there is just one watermill working for trade. Those that remain have mostly been converted. Such conversions include a garage, dwellings, restaurants, museums and a wedding venue. Some watermills are mere derelict shells, lower walls or lesser remains. Of the majority, there is nothing to be seen. A large number of tributaries feed into the River Medway. The tributaries that powered watermills will be described in the order that they feed in. The mills are described in order from source to mouth. Left bank and right bank are referred to as though the reader is facing downstream. This article deals with the watermills on the tributaries that feed in below Yalding.

Wateringbury Stream.
The Wateringbury Stream enters the Medway from the left at Wateringbury. A site close to the source of the Wateringbury Stream shows some characteristic signs of previous use of waterpower. Swanton, Mereworth A large pond high in the Swanton valley may indicate the site of an old furnace mill. The head available being sufficient to power a large overshot waterwheel. Mereworth Mill. The Domesday Book records two mills, value 10/-, at Marovrde (Mereworth). The site of the last mill now lies in the grounds of Mereworth Castle. In 1460, the mill was held by Thomas Hunte. In 1521 it was a fulling mill, belonging to Sir Thomas Nevyle. In 1772 James Pound was the occupant, followed by his widow in March 1780 and John Pound in September 1780. He was at the mill until October 1791. Thomas Edmead was at the mill from 1792-1827. The mill was purchased by Viscount Falmouth c.1856. The mill was demolished by 1907 and the site is today marked by a waterfall at the eastern end of the lakes in the grounds of Mereworth Castle. The head would have been some or , suggesting a high breast shot or overshot waterwheel., Mill at Wateringbury The Domesday Book records three mills at Otringeberge (Wateringbury). Two mills were held by Ralf, son of Turald and valued at 3/-, a third was held by Hugh de Braibourne and worth 16d. This mill was marked on C & G Greenwood's map of Kent, 1822. It was not mentioned in a survey of the parish carried out in 1828. Brattle (Upper) Mill, Wateringbury Brattle Mill was a corn mill. It was named after a miller, Robert Brattle. It was first mentioned in 1783 and was owned by Robert Brattle. In 1838 the mill was owned by Harry Blaker and occupied by William Mills. Harry Blaker died c.1848 and the mill was run for a short time by his widow, Sarah. James Fremlin took over the lease of the mill by 1851, also running Warden Mill. He purchased the mill from Sarah Blaker c.1868. The miller at this time being Alfred Bloorman. The original overshot waterwheel was of wood. It was replaced by a turbine c.1910 and it was about this time the mill was last used for milling, then being used to generate electricity. Brattle Mill was sometimes known as Upper Mill. A diameter by wide cast iron overshot waterwheel from Lower Mill, Polegate, Sussex, was reconstructed at the mill in the early 1980s and the owner intended to reconstruct the machinery to return the building to a working mill. The mill originally worked three pairs of millstones. Warden Mill, Wateringbury. Warden Mill was a corn mill that took its name from the farm to which it belonged, Warden Farm. The first reference to this mill was in November 1822, when John Savage of Cobham leased the mill from John Selby of Marden and John Fellow of Eynsford. In October 1829 James Fremlin took over the lease. Selby and Fellow(s) held the freehold of the mill until October 1838. In 1839 the area of the mill pond was given as ¾ acre. Charles Whittaker was the owner of the mill in 1842 and by April 1845 Whittaker and Fremlin were joint owners, but by November 1847 the mill had passed back to John Selby. James Fremlin purchased a moiety of the property in October 1871. He purchased the other share in the property in December 1876. Richard Clemetson took over the mill between 1878 and 1887, followed by William James Hawes sometime between 1890 and 1895. The mill last worked in 1913 and was demolished c.1914. The head of water was some . It is thought that this mill had a breast shot waterwheel., ==West Farleigh stream==
West Farleigh stream
A stream rises at West Farleigh, and flows into the Medway from the right above Teston Lock. It powered a watermill. Tutsham Oil Mill, West Farleigh Possibly a Domesday site, latterly the mill was an oil mill, burnt down on 17 April 1885. it was powered by a turbine. Only the front wall of the mill remains. ==Loose Stream==
Loose Stream
The Loose Stream or River Loose enters the Medway from the right at Tovil. Lambarde mentions thirteen fulling mills and one corn mill. Camden gives thirteen fulling mills. By c.1715 the Kentish cloth trade has declined, and Harris only mentions two fulling mills and one paper mill. Owing to the purity of the stream, paper making rose in importance in the nineteenth century. Brishing Court mill, Boughton Monchelsea TQ 779 515 The ancient manor of Brishing Court may have been the site of a mill. There is little evidence supporting the claim to a mill, which would have been demolished by the mid-Eighteenth century if it existed. Leg-o-Mutton (Wilson's) mill, Loose This mill took its name from the shape of the mill pond. It was in the ownership of the Wilson family in the 1870s. In its later life the mill was converted into three cottages, now demolished. The head of water being some to indicates an overshot waterwheel. Old (Gurney's) Mill Only the foundations of this paper mill remain, by Salts Lane. The mill was demolished after the First World War. It had an overshot waterwheel of diameter and wide., Loose village watermill This was a corn mill, probably the one mentioned by Lambarde. It had an overshot waterwheel driving three pairs of millstones, and was working until the First World War but subsequently demolished. Upper Crisbrook Mill. The seventeenth century structure latterly had a cast iron overshot waterwheel driving pumping machinery, working until the 1960s. The derelict waterwheel survived in the early 1970s and has now been restored, the mill buildings being house converted c.1975. Both the Crisbrook mills were the property of the dean and chapter of Canterbury. The ancient spelling of these mills was 'Christbrook/Chrisbrook'., Lower Crisbrook Mill. This late eighteenth century mill housed an internal water wheel; it was a corn mill c.1719. It had an overshot waterwheel driving four pairs of millstones. The mill last worked in 1905 and the machinery scrapped some thirty years later. An earlier mill on this site was probably the mill leased by the prior of Canterbury to Robert De Hucham. Only parts of the walls remain today. Bridge Mill. Originally a fulling mill, then a corn mill. A powder mill was established here in the eighteenth century and later an oil mill. Bridge mill was latterly a paper mill, ceasing work in the late twentieth century. The site has been cleared for a housing development. ==Loose Stream tributary==
Loose Stream tributary
Upper Mill, Loose. Originally a fulling mill, then a paper mill, latterly a corn mill with an overshot waterwheel driving three pairs of stones. This mill was in the ownership of the Wilson family in the 1870s. It closed in 1908 and has since been demolished. ==River Len==
River Len
The River Len enters the Medway from the Right at Maidstone. It powered a number of watermills, from source to mouth they were:- Polhill (Holme) Mill, Harrietsham. A Domesday site, Holme Mill is recorded as Holemiln in 1254 and Holemille in 1332. In 1542 the manor of Polhill was in the ownership of John Stede. The mill passed to his son Thomas and then to his son Matthew. The mill was owned by Francis Colepeper Esq at the time of his death in 1590. It was worth 40s per annum then. In 1668 the mill was held by John Ruffen. It was the a fulling mill. Peter Theobalds was the tenant at the time of his death in 1690. About this time the mill was converted to a corn mill. Stephen Weeks was the miller from 1700–1726, followed by his son John. He was followed by his son Thomas. Thomas Knight leased the mill for 21 years from 1779. He was followed by George Cronk and then John Brazier and Thomas Martin, who was the miller in 1824. In 1847 John Bunger was the miller, followed by William and Thomas Taylor in 1855. In 1895, the mill was in the occupation of Miller Bros, followed by Mrs Rhoda Vinson from 1907 - 1913. The mill had collapsed by the time Coles Finch visited it and was demolished in 1929, although the waterwheel and pentrough by Weeks of Maidstone survive. The Mille, Broomfield Possibly a Domesday site, the mill was marked on a map dated 1649. A 1748 map shows the watercourses but no mill. The head of water available was some , indicating a breast shot or overshot waterwheel. Keepers Cottage mill, Broomfield A possible mill site, a building was marked on a map of Leeds Castle dated 1748 on the island which lies above Keeper's Cottage. The site is probably not a Domesday site and if a mill existed here it disappeared in the late Middle Ages. Brandescombe (Buscombe, Fulling) Mill, Leeds This mill was presented to the Priory of Leeds by Robert de Crevecoeur the Younger. The mill was also mentioned in the will of Daniel de Crevequer, who died in 1177. At that time it was a corn mill. Leeds priory was dissolved in 1539 and the mill was still in the ownership of the priory then. In 1628, Thomas Fludd and Ralphe Buffkin sold the mill to William Cage of Lincoln's Inn, Middlesex. By this time it was a fulling mill. Cage was still the owner in 1689, when the mill was in the occupation of William Tompkin and had previously been in the occupation of Bob Potter. Potter remained in occupation until at least 1707. Hasted noted the mill was still working in 1798 and Greenwood's map of 1822 marks the mill as Shilling Mill. The mill probably had a breast-shot waterwheel as the head was not sufficient for an overshot wheel. Fulling Mill had ceased to be used as a mill by 1843, there being no entry in Bagshaw's Directory of that year. The surviving building is of the fifteenth century. Thurnham Mill. This mill was built by the Cage family in the late 1820s on a piece of land called Byfrance, part of the Milgate estate. The tail race from Ballard's Mill was extended some to get sufficient height to drive an overshot waterwheel of diameter and wide. The waterwheel was carried on a cast iron axle and drove a diameter cast iron pit wheel with wooden cogs. That drove the wallower on the upright shaft, then a diameter cast iron great spur wheel drove four pairs of millstones. There were two pairs of French burr stones and two pairs of Peak stones. One pair of each type was diameter and the other pair of each type was diameter. At the top of the upright shaft was a diameter cast iron crown wheel. The Blinkhorn family had a long association as millers at the mill, John Blinkhorn being the miller in 1825. J Blinkhorn was the miller in 1852 and John Blinkhorn in 1874. A new waterwheel was fitted after World War I. Marshall Bros were the millers 1930 - 1934. The mill was working until World War II when the axle to the waterwheel broke. Most of the machinery was then scrapped. The mill was sold for house conversion in 1986, at that time only the frame of the waterwheel and pit wheel survived, all other machinery having been removed. Otham Mill. Also known as Bearsted Mill, this corn mill was built in 1837. It was still standing in 1939 and the overshot waterwheel had a width that exceeded its diameter. Otham Paper Mill Originally built as a fulling mill in 1527. The machinery was to be made by Cranbrook millwright George Jenkyn. The mill was to have two overshot waterwheels diameter. The contract was signed on 8 January 1527, with the mill to be completed by May Day. Total cost of the mill was £88 5s 3d. The mill had been converted to a paper mill by 1700. By the 1830s Otham Paper Mill was occupied by the papermakers at Turkey Mill. A paper making machine was installed, but removed to Turkey Mill in 1859, when the mill was converted to house a two engine washer for cleaning and beating rags for use in the papermaking process. The mill was marked on the first 6" Ordnance Survey map. Church Mill, Maidstone. Church mill was one of the two mills in Maidstone owned by Christ Church, Canterbury. It may be one of the five Domesday mills recorded in Maidstone. Church mill was standing in 1572. William Purtis/Purlis was the miller in 1752, renewing his lease on the mill in that year. An inventory at the time showed that Church mill had two pairs of French Burr millstones and one pair of Peak millstones. It was marked on Brown & Son's survey of Maidstone, 1821. The mill was demolished in 1903 as part of a road widening scheme. The millpond survives., Little Church Mill, Maidstone. This mill stood on the watercourse that was the bypass from Church Mill. William Purtis/Purlis was the miller in 1752, renewing his lease on the mill in that year. An inventory at the time showed that Little Church mill had one pair of French Burr millstones and four bolting mills. It was marked on Brown & Son's survey of Maidstone, 1821. The mill demolished in the early nineteenth century., ==Selesbourne (Len tributary).==
Selesbourne (Len tributary).
Mill at Harrietsham This was a grinding (corn) mill. ==The Fair Bourne (Len tributary).==
The Fair Bourne (Len tributary).
Fairbourne Mill, Harrietsham This mill was probably a Domesday mill. The first definite reference to this mill was in 1580, when the rent was assessed at 9 hens, commuted to 2d. The mill was called Fulborne Mill in 1608. It was owned at that time by James I but sold by him shortly afterwards. Edward Hickmut was the occupier of the mill in 1694. In 1768, the mill was described as "two water corn mills under one roof". It was then in the occupation of Thomas Stiles. Alexander Bottle was the miller from 1782–1797. He rebuilt the mill in 1796, which date was to be seen on the mill. This was a corn mill with an overshot waterwheel driving two pairs of millstones, one pair of French Burrs and one pair of Peaks. William Hudson was the miller from 1847–1855. Thomas Clark (1838–1929) was the miller through the second half of the nineteenth century, taking the mill c. 1861. He was the miller until the mill stopped working. The waterwheel was later replaced by a turbine. Milling at Fairbourne ceased in 1908. Although the waterwheel was never at a loss for water to supply it, it could only work one of the two pairs of millstones at any one time. The mill building remains, empty of machinery. ==Hollingbourne Stream or Snagbrook (Len tributary).==
Hollingbourne Stream or Snagbrook (Len tributary).
The Hollingbourne Stream rises at the foot of the North Downs, and flows for to the River Len. It powered four mills. Alternative names for the stream are the Snagbrook and the Snakebrook. Eyhorne Mill. This corn mill may have been owned by Edward Laws in 790. It was at work in 1839 when the owner was James Bunyard and the miller was John Symmonds. In 1855, the miller may have been John Adley. It last worked sometime between 1885 and 1898, when it was marked as disused on the Ordnance Survey map. The mill stood downstream of the bridge and on the east bank of the stream. The waterwheel was probably breastshot as the head was only some or . The mill was disused by 1898., ==Leeds Stream (Len tributary)==
Leeds Stream (Len tributary)
Le Nethertoune Mill, Leeds. This mill stood probably had a breastshot or undershot waterwheel as the head available would only have been some . It was a fulling mill recorded as being "in ruins" in 1466. Abbey Mill, Leeds. Probably a Domesday site and one of the five mills owned by the Townsmen of Leeds. Leeds Priory was surrendered in 1539 and in 1540 the King leased the site of Leeds Priory and all houses, mills etc. to Sir Anthony St Leger for 21 years. The St Leger family continued the lease until 1573 when it passed firstly to the Norden family and then to William Covert and later his son, William. In 1609, the estate was sold to Sir William Meredith, in whose family it remained until the eighteenth century. In 1789, and indenture between John Calcroft and Thomas William mentioned that the mill was formerly in the possession of Thomas Crisp. George Blinkhorn was the miller from 1843–1874 and Alfred Blinkhorn was the miller from 1895 - 1922. The mill was marked on the first 6" OS map of Kent in 1865. It had a cast iron overshot waterwheel diameter and wide by Weeks of Maidstone. The cast iron Pit Wheel was diameter with wooden cogs. The waterwheel drove three pairs of millstones via two lineshafts, each driven by a diameter cast iron gear. One shaft drove a single pair of diameter French Burr millstones by a diameter cast iron face gear with wooden cogs and the other shaft drove two pairs of French Burr millstones by diameter cast iron face gears with wooden cogs. One pair of stones was diameter and the second pair diameter. Both lineshafts were of oak, square. The mill was derelict but intact in 1936 but partly demolished later, with only the ground floor remaining. Some machinery still remains in the mill. Priory (North) Mill, Leeds The mill was first recorded as belonging to James I in 1608, known then as North Mill. The site of this mill was recorded on a map of 1821. In 1834, only a few fragments of the mill walls remained. The head would have been around , suggesting a breastshot waterwheel. ==Bearsted Stream (Len tributary)==
Bearsted Stream (Len tributary)
A stream rises above Bearsted. It powered two mills. Aldington Mill, Thurnham Aldington mill was a Domesday mill. In 1269 it was held by William de Cobeham. Lower Milgate Mill, Bearsted. This mill stood was part of a small estate known as The Comb. It was in existence during the first half of the eighteenth century, appearing on a map of 1707 which was partly resurveyed in 1746. ==Cossington Stream.==
Cossington Stream.
A stream rises at Cossington and enters the Medway from the right at Aylesford. It powered a watermill. Cossington Mill. This was a corn mill. ==East Malling Stream.==
East Malling Stream.
The East Malling Stream enters the Medway from the left at Aylesford. The Domesday Book recorded two mills worth 10/- at Metlinge (East Malling). In 1363 there were two mills in the village. East Malling possessed a fulling mill from 1567 to 1719, most likely to have been Middle Mill. Thomas Tomlyn was a miller in the seventeenth century, Thomas Pidgeon, corn miller of East Malling died in 1685, In 1706 there were three mills - Upper, Weir and Middle Mills. The history of the paper mills needs to be read together, as they were all linked through various owners. Upper Mill, East Malling. James Brooks was the at the mill in 1752, when the mill was rated at £61, increasing to £122 in 1757. By 1764 the mill was operating as a paper mill, James Brooks insuring the mill for £150 in that year. One of his apprentices wa Nicholas Tapsfield, who was later to work at the paper mill at Sundridge. In 1801 he insured the mill for £350 and died in 1805 aged 69. John Larking took the mill 1n 1806, it being then rated at £131. Larking went into partnership with John Morrice by 1816 and Morrice was recorded as at the mill from 1817-21. He was succeeded by William Blunden, who was working at Upper Mill in 1819, followed by Robert Tassell c.1823. The mill underwent considerable development between 1840 and 1860. It was demolished in the years between the First and Second World Wars. An illustration of Upper Mill can be seen here. The mill pond was some long, and covered an area of just over ½ acre in 1840. The mill had an overshot waterwheel of some diameter and wide, the remains of which were on site in 1972. The tail race discharged into the mill pond of Weir Mill. Weir Mill, East Malling. Probably one of the two Domesday mills. The mill was marked on a map of 1706. The next known mention of Wier Mill was in 1810 when the mill was marked on the map accompanying the enclosure award. In 1840 James Phillips was the owner-occupier of the mill, which was a water corn mill with waterwheel driving two pairs of stones. The pond of Weir Mill is roughly square in shape and covers an area of just over ¼ acre. The mill passed from James to Thomas Phillips c.1855 and to Mr. T J Dewe c,1893. G E Hide was working the mill in 1905 and S R Anscombe bought the mill in 1913. The mill last ground corn in 1930 and was bought by Whitbread Ltd., the Maidstone brewers, who used part of the mill to store hops. The mill subsequently passed into the ownership of Wm. Lillico & Son and was then used as a general store. During this time the timber part of the mill buildings were becoming derelict. ;The surviving mill building The timber clad original mill building dates from the reign of Queen Anne. A brick extension was added in two stages, the last part being built in 1889. Roller mills of 4½ sack capacity were installed c.1893 as was a boiler and steam engine, principally to drive the roller mills whilst the waterwheel drove the stones. The steam engine was a beam engine, it was eventually sold to a buyer in the USA. ;The wooden mill This is four storeys in height, the base being of brick and the upper storeys timber. The diameter waterwheel was overshot with eighty buckets and carried on a diameter cast iron axle. The wooden upright shaft was only diameter, reducing to at first floor level. It carried a Great Spur Wheel and an iron Crown Wheel of diameter. This received a drive from the steam engine so that the mill could be driven that way if necessary. The mill drove three pairs of millstones. ;The brick mill This was built in two parts, latterly known as the "middle room" and the "end room", this last part being built in 1889. The mill was some six storeys in height, dwarfing the original mill. The middle room contained the roller mills, six in total. Middle Mill, East Malling. Probably one of the two Domesday mills. Middle Mill was in existence in 1684 when the pond was shown on a map drawn by Abraham Walter. In 1755 Richard Gowlett was the papermaker here, and in that year he took John Evernden and Elizabeth Sands as apprentices. He insured the mill for £35 in 1770 and he died c.1778, his widow Mary paying the rates on the mill until 1798 when the mill was sold to George Blunden. William Blunden was at the mill in 1816, but George Blunden was again recorded at the mill in 1824. He was recorded at a manufacturer of brown and white paper in 1832 and Francis Collins joined him in partnership that year. Robert Tassell acquired the mill c.1833 and went into partnership with Henry Smith in 1838. In 1841 there was an increase in the rateable value of the property from £54 to £150. The partnership was dissolved in 1848, all three mills being in the sole ownership of Robert Tassell from 1834 to 1838. The mill stood empty from 1848 to 1850, when the Busbridge brothers took over the running of the mills. They were involved in a Court case in 1859 over the discharge of foul water used in the paper making process. The mill pond covered an area of just over ½ acre. An illustration of Middle Mill can be seen here., Lower Mill, East Malling. In 1792 Clement and George Taylor were granted a patent for the use of chlorine for bleaching rags for use in paper manufacture. James Whatman claimed that he was able to prove that several trials had already been made, including by Mr. Larking, who owned Lower Mill at that time. In 1816, John Larking and John Morrice were in partnership at both Upper and Lower Mills, the partnership being dissolved on 8 October of that year, John Morrice taking both mills. Robert Tassell took both mills by 1821, making both brown and white papers. He went into partnership with Henry Smith in 1838 and by 1844 they owned all three paper mills. This partnership was dissolved c.1844 and Henry Smith was the sole occupier of the three mills, worth together £420. In 1848 Lower Mill was recorded as empty and valued at £120. All three mills were managed by Thomas Harris Busbridge and George Frederick Busbridge from c.1849. It is likely that Lower Mill ceased regular production of paper in 1848, being used spasmodically until 1851, and closing completely by 1852. The mill seems to have been demolished by 1860, not appearing on the first 25-inch Ordnance Survey map. The mill pond is some long and wide, covering an area of just under 1½ acres (6,100 m2)., Church Mills, Ditton. A Domesday site, one mill was recorded at Dictvne (Ditton) with a value of 10/-. Tenants of this corn mill include Edward Smith in 1724, J Whiteing from 1725–43, Thomas Shepard 1744-54, his widow in 1755-6, William Luck in 1757. Thomas Allchin was at the mill in 1840 and was still there in 1852. Joseph Jellis was the miller in 1887-90 and Robert Foster was the last known miller in 1905. The mill closed down c.1912. The mill is located close to the ford in Bradbourne Lane. In its later years the waterwheel was replaced by a turbine. Mill Hall Mill, Aylesford. This mill was marked on a map of 1684, it was a paper mill at that time. In 1695 Edward Middleton was working the mill, which then had a rateable value of £20. He was at the mill until 1724 when William Harris took it over. William Harris died in 1741 and his widow ran the mill until 1744 when Thomas Harris took it over. He was still at the mill in 1763 when he insured the mill for £100. in 1776 Thomas Golding insured the mill. He was still at the mill in 1803 but by 1812 his son Stephen Golding was recorded as a master paper maker of Ditton when he married. There was a partnership between Thomas Golding and his sons Stephen and Thomas jr which was dissolved in 1816. The artist Jean Claude Natteas (1785–1822) sketched the mill in 1816. In 1832, Robert Tassell took over the mill and it ceased to make paper by 1841. In 1841, Stephen Spratt was recorded as the occupier of the mill, by then a corn mill. he was at the mill until at least 1862, the next change of ownership being recorded as Charles Stonham & Sons in 1878. A steam engine was recorded at the mill in 1887, but had gone by 1890, when Walter Skinner was the miller, still there in 1895. Henry Packham was the last miller, there at least 1905-13, but the mill had stopped working by 1922. The machinery was removed and the building converted into stables by A E Reed & Co. Ltd. the mill was demolished c.1950 but the waterwheel survived until 1969. The mill was of three storeys, the base being of ragstone and the upper storeys of timber, clad in tarred weatherboarding. The overshot waterwheel was diameter and wide, mounted on a square iron axle, driving an iron pit wheel. The iron pentrough was dated 1887. The final remains of Mill Hall Mill were demolished to make way for the foundations of a footbridge over the M20., ==Boxley Stream==
Boxley Stream
A stream rises at Boxley. It powered a watermill. Sandling Mill This mill was built as a papermill. William and Reuben Hunt were at the mill in 1839. It was later converted to a corn mill and was marked as such on nineteenth-century maps. In 1984, it was offered for sale with potential for conversion. Planning permission was granted in 1991 for house conversion, with a condition being made that the waterwheel was to be replaced. In 2005, the building burnt down, leaving the ragstone base standing. ==Addington Brook.==
Addington Brook.
A stream enters the Medway from the left at Snodland. It powered six watermills. Ford Place Mill, Wrotham. This was a corn mill, in the Le Clerke family's ownership for many years, until the last member died in the Battle of Cropredy Bridge. The mill was later in the Best family's ownership. The eighteenth-century building remained in 1932, empty of machinery. The waterwheel was overshot approximately diameter and wide. The mill building was demolished in 1970 to construct the M26., Addington Mill. This was a corn mill, demolished in the nineteenth century. The site now lies within the West Malling Golf Course. Leybourne Mill. A Domesday site Leybourne Mill was a corn mill. The waterwheel was oveshot. Mill site, Leybourne. Ham Mill, Snodland. This was a corn mill. ==Holborough Stream.==
Holborough Stream.
A stream rises above Snodland, and enters the river from the left downstream of the Addington Brook. It powered a watermill. Holborough Mill. A very ancient mill site, a mill was presented by King Egbert I of Kent to Bishop Beormond of Rochester in 836. In 1100 it was valued at £1. The mill had fallen into disrepair in the early fourteenth century, but was rebuilt by Bishop Hamo Hethe in 1322. The surviving mill building has a cast iron overshot waterwheel, diameter. It was a corn mill. • = • = • = • = ==References==
tickerdossier.comtickerdossier.substack.com